1、A. E .C. M .A. STAN DAR D NORM E A. E.C. M.A. A.E.C.M.A. NORM Edition approved for publication Comments shouid be sent within six months after the date of publication decision Technopolis - 175, rue Jean-Jacques Rousseau 921 38 Issy-les-Moulineaux Cdex - FRANCE 1992-06-05 A.E.C.M.A. prEN 2591 Part D
2、8 Issue P I June 1992 C2 Chairman M. J. LE CUNFF DIT PAR LASSOCIATION EUROPENNE DES CONSTRUCTEURS DE MATRIEL AROSPATIAL Technopolis - 175, rue Jean-Jacques Rousseau - -92t 38 Issy-les-Moulineaux Cdex - Tl. (1) 47.36.98.76 UDC : Key words ENGLISH VERSION Aerospace series Elements of electrical and op
3、tical connection Test methods Part D8 - Mating and unmating forces Srie arospatiale Luft- und Raumfahrt Mthodes dessais Prufverfahren Organes de connexion lectrique et optique Partie D8 - Forces daccouplement et de dsaccouplement Elektrische und optische Verbindungselemente Teil D8 - Kupplungs- und
4、Trennkrfte This Aerospace Series pre-standard has been drawn up under the responsibility of AECMA (Association Europenne des Constructeurs de Matriel Arospatial). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Commissio
5、n following comment by the Member countries. Subsequent to the publication of this pre-standard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the
6、AECMA Standard Checking Centre (NPS) and formal agreement of the Official Services of the Member countries it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for final vote. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provi
7、ded by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-f -. CEN PREN*2591 (PART*DB) 92 3404589 O027056 1 I prEN 2591-D8 Page 3 1 Scope and field of application This standard specifies a method of measuring the axial forces or torque mome
8、nts required to fully mate or unmate elements of connection, including the effect of any device that assists the matinghnmating separating operations. It shall be used together with EN 2591. 2 References EN 2591 Aerospace series - Elements of electrical and optical connection - Test methods - Genera
9、l 3 Preparation of specimens 3.1 Specimens shall be fitted with their full complement of wired contacts and their normal accessories as specified by the technical specification. The receptacle shall be mounted to a support. 3.2 Unless indicated in the technical specification, the following details s
10、hall be specified : - type and length of cable, - type of accessory, - test method A or A and 6, - temperature for method 6, - rate of application of the load, if required, - method A or B : maximum value of mating force or torque, - method A or B : maximum and minimum values of unmating force or to
11、rque. 4 Method 4.1 Procedure The plug shall be fully mated and unmated by the normal method. If necessary, the rate of mating or unmating shall be as specified by the technical specification. . Previous page is blank Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided
12、by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,- CEN PREN*K2591 (PART*DB) 92 I 3404589 0027057 3 I prEN 2591-D8 Page 4 Method A : specimens shall be tested at room ambient temperature. Method B : specimens shall be tested for 2 h at a
13、 temperature between -25 OC and -55 OC as specified by the technical specification. The forces and/or torque moments required to fully mate or unmate specimens shall be measured. 4.2 Requirements The forces or torques measured shall be within the limits specified. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
