1、ASD STANDARD NORME ASD ASD NORM prEN 3264 Edition P 3 October 2009 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONAvenue de Tervuren, 270 - B-1150 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8131 - www.asd-stan.orgICS: 49.030.30 Supersedes edition P 2
2、of March 1995 and will supersede EN 3264:2001 Descriptors: ENGLISH VERSION Aerospace series Pipe coupling 830 in titanium alloy Thrust wire nuts Srie arospatiale Systme de raccordement 830 en alliage de titane crous jonc Luft- und Raumfahrt Rohrverschraubung 830 aus Titanlegierung Muttern mit Schubd
3、raht This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the con
4、cerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and fo
5、rmal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status
6、 of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 October 2009 Comments should be sent within six months after the date of publication to ASD-STAN Mechanical Domain Copyright 2009 by ASD-STAN Copyright ASD-STAN Provided by
7、IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3264:2009 (E) 2 Contents Page Foreword2 1 Scope 3 2 Normative references 3 3 Required characteristics.3 4 Designation 5 5 Marking .6 6 Technical specification .6 Foreword This standar
8、d was reviewed by the Domain Technical Coordinator of ASD-STANs Mechanical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. Copyright ASD-STAN Provided by IHS under
9、 license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3264:2009 (E) 3 1 Scope This standard specifies the characteristics of thrust wire nuts for pipe couplings 830, in titanium alloy, for aerospace applications. Nominal pressure: up to 28 000 kP
10、a Temperature range: 55 C to 135 C 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)
11、applies. EN 2424, Aerospace series Marking of aerospace products EN 2491, Aerospace series Molybdenum disulphide dry lubricants Coating methods EN 3275, Aerospace series Pipe coupling 830 up to 28 000 kPa Dynamic beam seal - Metric series Technical specification EN 3311, Aerospace series Titanium al
12、loy TI-P64001 Annealed Bar for machining D 150 mm 1)EN 3314, Aerospace series Titanium alloy TI-P64001 Solution treated and aged Bar for machining D 75 mm 1)EN 4032, Aerospace series Pipe coupling 830 in titanium alloy Thrust wire ISO 5855-3, Aerospace MJ threads Part 3: Limit dimensions for fitting
13、s for fluid systems ISO 8788, Aerospace Nuts, metric Tolerances of form and position 3 Required characteristics 3.1 Configuration Dimensions Mass According to Figure 1 and Table 1. The values apply before lubricating. 3.2 Surface roughness According to Figure 1. 1) Published as ASD-STAN Prestandard
14、at the date of publication of this standard. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3264:2009 (E) 4 3.3 Material According to EN 3311 or EN 3314 3.4 Surface treatment Lubrication: according t
15、o EN 2491, on the bottom of the groove only. Prior to application of the lubricant the surface shall be abrasive blasted using non-metallic grit. Film thickness: 0,005 mm to 0,013 mm Dimensions in millimetres aArea for marking bThread c0,3 to 0,5 applicable to both faces Figure 1 Copyright ASD-STAN
16、Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3264:2009 (E) 5 Table 1 Dimensions in millimetres Threadb d1 d2 d3 d4c e l1l2l3d l4l5m r s Te Mass g/piece Codea 4H5H 0,1 0 0,2 + 0,1 0 + 0,10 min. 0,4 0,1 max. 0,1 h11 +
17、0,1 0 h13 max. 05 MJ10 1 9,1 11,0 15,51 4,2 7,2 8,4 10,0 13,0 14 0,36 5,52 06 MJ12 1,25 10,8 12,6 17,77 5,2 8,0 9,2 11,0 14,0 16 7,36 08 MJ14 1,5 12,6 17,0 14,6 20,03 11,0 6,2 9,5 11,0 13,0 16,0 18 7,59 10 MJ16 1,5 14,6 19,0 16,6 2,2 23,36 7,2 16,5 1,3 21 9,00 12 MJ18 1,5 16,6 21,0 19,2 24,49 8,2 17
18、,5 22 0,4310,64 14 MJ20 1,5 18,6 23,0 21,2 26,7510,59,214,0 18,0 24 11,56 16 MJ22 1,5 20,6 26,0 23,2 2,7 30,14 10,21,6 27 17,50 18 MJ24 1,5 22,6 28,0 25,2 33,53 11,2 30 23,66 20 MJ27 1,5 25,6 31,0 28,2 35,72 12,5 32 23,23 22 MJ30 1,5 28,6 35,0 31,2 39,9810,013,719,0 36 0,5227,72 25 MJ33 1,5 31,6 38,
19、0 34,2 45,63 15,5 41 36,63 28 MJ36 1,5 34,6 41,0 37,2 51,28 17,219,5 46 42,00 32 MJ39 1,5 37,6 45,0 40,2 3,2 55,809,518,610,5 12,014,5 20,0 1,9 50 0,6251,45 aCorresponds to the pipe nominal outside diameter. bAccording to ISO 5855-3. cCorresponding wire diameter according to EN 4032. dMinimum usable
20、 thread length. eAccording to ISO 8788. 4 Designation EXAMPLE Description block THRUST WIRE NUT Identity block EN3264-05 Number of this standard Code (see Table 1) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. Copyright ASD-STAN Provided by I
21、HS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3264:2009 (E) 6 5 Marking According to EN 2424, style A and Figure 1. 6 Technical specification According to EN 3275, type II. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-
