1、ASD STANDARD NORME ASD ASD NORM prEN 4644-001 Edition P 1 December 2008 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Avenue de Tervuren, 270 - B-1150 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: 49.060 Descriptors: ENGLISH
2、 VERSION Aerospace series Connector, electrical and optical, rectangular, modular, rectangular inserts, operating temperature 175 C continuous Part 001: Technical specification Srie arospatiale Connecteur, lectrique et optique, rectangulaire, modulaire, inserts rectangulaires, temprature de fonction
3、nement 175 C continu Partie 001 : Spcification technique Luft- und Raumfahrt Elektrische und optische Rechtecksteckverbinder, modular, rechteckige Kontakteinstze, Dauerbetriebstemperatur 175 C konstant Teil 001: Technische Lieferbedingungen This “Aerospace Series“ Prestandard has been drawn up under
4、 the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publi
5、cation of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft Euro
6、pean Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standard
7、s conflicting with the EN. Edition approved for publication 31 december 2008 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2008 by ASD-STAN Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or n
8、etworking permitted without license from IHS-,-,-prEN 4644-001:20082 Contents Page Foreword2 Introduction .3 1 Scope 3 2 Normative references 3 3 Terms and definitions .4 4 Description .5 5 Design 16 6 Dimensions and masses 17 7 Tests. 64 8 Quality assurance. 78 9 Designation and marking. 85 10 Deli
9、very conditions. 86 11 Packaging 86 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval
10、for Publication. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4644-001:2008 3 Introduction The connectors defined by this standard are suitable for use on board of commercial and military aircraft
11、for both disconnect panel and rack and panel applications in severe environmental conditions. 1 Scope This standard specifies the required characteristics, the condition for qualification, acceptance and quality assurance for electrical and optical rectangular connectors with single or multiple remo
12、vable rectangular inserts for use in a temperature range from 65 C to 175 C continuous for electrical contact. This family of connectors is particularly suitable for aeronautic use in zones of severe environmental conditions on board aircraft, applying EN 2282. Inserts for fiber optic contacts or mi
13、xing fiber optic contacts and electrical contacts are described in EN 4639-002. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the re
14、ferenced document (including any amendments) applies. EN 2266-003, Aerospace series Cables, electrical, for general purpose Operating temperatures between 55 C and 200 C Part 003: Ink jet printable Product standard. EN 2267-003, Aerospace series Cables, electrical, for general purpose Operating temp
15、eratures between 55 C and 260 C Part 003: Ink jet printable Product standard. EN 2282, Aerospace series Characteristics of aircraft electrical supplies. EN 2591-100*, Aerospace series Elements of electrical and optical connection Test methods Part 100: General. EN 3155-002, Aerospace series Electric
16、al contacts used in elements of connection Part 002: List and utilization of contacts. EN 3909, Aerospace series Test fluids and test methods for electric components and sub-assemblies. EN 4530-002, Aerospace series Sealing sleeves used in elements of connection Part 002: List and utilization of sea
17、ling sleeves. *And all parts quoted in this standard. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4644-001:20084 EN 4639-002, Aerospace series Connectors, optical, rectangular, modular, multiconta
18、ct, 1,25 mm diameter ferrule, with removable alignment sleeve holder Part 002: List of product standards. EN 4639-101, Aerospace series Connectors, optical, rectangular, modular, multicontact, 1,25 mm diameter ferrule, with removable alignment sleeve holder Part 101: Optical contact for cable EN 464
19、1-100 Operating temperature between 65 C and 152 C Product standard. 1) EN 4639-102, Aerospace series Connectors, optical, rectangular, modular, multicontact, 1,25 mm diameter ferrule, with removable alignment sleeve holder Part 102: Optical contact for cable EN 4641-102 Operating temperature betwee
20、n 55 C and 100 C Product standard. 1)EN 4644-002, Aerospace series Connector, electrical and optical, rectangular, modular, rectangular inserts, operating temperature 175 C continuous Part 002: Specification of performance and contact arrangements. 1)EN 4644-003, Aerospace series Connector, electric
21、al and optical, rectangular, modular, rectangular inserts, operating temperature 175 C continuous Part 003: Rectangular insert Product standard. 1)EN 4644-103, Aerospace series Connector, electrical and optical, rectangular, modular, rectangular inserts, operating temperature 175 C continuous Part 1
22、03: dust caps Product standard. 2)EN 4644-201, Aerospace series Connector, electrical and optical, rectangular, modular, rectangular inserts, operating temperature 175 C continuous Part 201: rear accessories Product standard. 2)EN 9100, Aerospace series Quality management systems Requirements (based
23、 on ISO 9001:2000) and Quality systems Model for quality assurance in design, development, production, installation and servicing (based on ISO 9001:1994). EN 9133, Aerospace series Quality management systems Qualification Procedure for Aerospace Standard Parts. MIL-HDBK-454B, General guidelines for
24、 electronic equipment. 3)SAE AS31971, Connectors, high reliability, space use, general specification for.4)SAE AS39029/1, Installing and removal tools, connector electrical contact, general specification for.4)3 Terms and definitions For the purposes of this document, the terms and definitions given
25、 in EN 2591-100 and the following apply. The reference planes and axis used in this product standard are listed below: Ap : shell bottoming reference plane on male housing. Ar : shell bottoming reference plane on female housing. 1) Published as ASD Prestandard at the date of publication of this stan
26、dard. 2) In preparation at the date of publication of this standard. 3) Published by: Department of Defense (DoD), the Pentagon, Washington, DC 20301, USA. 4) Published by: Society of Automotive Engineers, Inc. (SAE), 400 Commonwealth Drive, Warrendale, PA 15096-0001, USA. Copyright ASD-STAN Provide
27、d by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4644-001:2008 5 AC : aligning housing cavity Bp : vertical axis of male housing Br : vertical axis of female housing Cp : horizontal axis of male housing Cr : horizontal axis of
28、female housing N : extremity of insert retention clip reference plane NC : non aligning housing cavity P : front face of hard insert R : vertical axis of housing backshell interface S : horizontal axis of housing backshell interface T : backshell bottoming reference plane on housing X : horizontal a
29、xis of insert Y : vertical axis of insert 4 Description 4.1 General This family of connectors is divided into two types of connectors which are the following: disconnect panel connectors; rack and panel connectors. The current revision of this standard is describing 2 disconnect panel housing sizes
30、and 1 rack and panel housing size. However, it is also providing a design rule to extend the current range described. The design rule is based on the description of housing aligning cavities, housing non aligning cavities and a clinging dimension line; see 4.2 and 4.3 for details. These connectors h
31、ave rectangular housings, removable rectangular inserts and contacts and can be fitted with rear accessories. Male and female inserts can be fitted either in the male or female housing. Depending on the housing size, the disconnect panel connectors are mated and unmated either by using a centre coup
32、ling screw or 2 quarter turn fasteners. The centre coupling screw and coupling nut can be installed either on the male or female housing. The centre coupling mechanism shall provide a total of 12 polarization positions. Housings having the quarter turn fasteners are polarised by using 2 polarizing p
33、osts and keys offering a total of 16 polarizing positions. A size 1 housing has 1 insert cavity with 1 keyway, a quarter turn fastener and 2 polarizing posts or keys. A size 2 housing has 2 insert cavities with one cavity having one keyway and the other having two keyways; a central coupling mechani
34、sm provides housing polarization. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4644-001:2008 6 There is only one rack and panel (blind mate) connector housing size; it is a size 3 housing which has
35、 3 insert cavities all with one keyway, three polarizing posts or keys offering 64 polarizing positions and no locking mechanism. These connectors use different types of contacts (signal, power, coaxial, triaxial, quadrax, etc.) defined in EN 3155-002 and optical contacts defined in EN 4639-101 and
36、EN 4639-102. 4.2 Female housing 4.2.1 General Size 1 and 3 female housings shall be attached by rectangular flange with two mounting holes, size 3 housing has floating eyelet mounting holes or through holes. The size 3 housing has 4 pins, each of which can take 2 positions, to polarise the shell wit
37、h the panel on which it is mounted. Size 2 female housing are either panel mount connector or cable connector. Panel mount receptacle connector shall be attached by rectangular flange with two mounting holes. The insert cavities are identified on the female housing by letters A, B, C for size 3 lett
38、ers A, B for size 2 and no letter for size 1. The insert cavities are polarizsed by either one (A polarizing position) or two keyways (B polarizing position) location. Housing size 1 and 3 insert cavities have one keyway. Housing size 2 insert cavity identified with letter A has one keyway and inser
39、t cavity identified with letter B has two keyways. Each insert cavity has 2 insert retaining devices allowing rear insertion and rear release of the insert. Each female housing has a grounding device ensuring electrical continuity between housings before contact mating. In addition, size 1 and 2 fem
40、ale housings are available with (classes B and F) or without a grounding block (classes A, C and E) allowing grounding of a cable braid with a pigtail. 4.2.2 Disconnect panel female housing All disconnect panel female housing have a minimum of 1 (for single cavity connectors) and a maximum of 2 alig
41、ning housing cavities (see Figure 1); the remaining housing cavities are non aligning cavities (see Figure 2). Non aligning female housing cavities have a circular location tolerance. In order to define how alignment of the female and male housing is achieved a dimension line between the 2 housing a
42、ligning cavities is defined. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4644-001:20087 Key 1 Dimensions for housing size 1 2 Dimension for housing size n (n 1) 3 Dimension of grounding device (op
43、tional) Figure 1 Disconnect panel female aligning cavity (AC) Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4644-001:20088 Key 1 Dimension of grounding device (optional) Figure 2 Disconnect panel fe
44、male non aligning cavity (NC) 4.2.3 Rack and panel female housing Rack and panel female housing have a minimum of 1 (for single cavity connectors) and a maximum of 2 aligning housing cavities (see Figure 3); the remaining housing cavities are non aligning cavities (see Figure 4). Non aligning female
45、 housing cavities have a circular location tolerance. In order to define how alignment of the female and male housing is achieved a dimension line between the 2 housing aligning cavities is defined. 1Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or network
46、ing permitted without license from IHS-,-,-prEN 4644-001:2008 9 Key 1 Dimension for grounding device Figure 3 Rack and panel female aligning cavity (AC) Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN
47、 4644-001:2008 10 Key 1 Dimension for grounding device (optional) Figure 4 Rack and panel female non aligning cavity (NC) 4.3 Male housing 4.3.1 General Size 1 and 3 male housings shall be attached by rectangular flange with two mounting holes; Size 2 male housing are either panel mount connector or
48、 cable connector. Panel mount connector shall be attached by rectangular flange with two mounting holes. The insert cavities are identified on the male housing by letters A, B, C for size 3 letters A, B for size 2 and no letter for size 1. The insert cavities are polarized by either one or two keyways location. Housing size 1 and 3 insert cavities have one keyway. Housing size 2 insert cavity identified with letter A has one keyway and insert cavity identified with letter B has two keyways. Copyrig
