1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: WR-ALC 542 CSW/CBSSS, 295 Byron Street, Robins AFB, GA 31098-1611. Since contact information can change, you may want to verify the currency of this address
2、 information using the ASSIST Online database at https:/assist.daps.dla.mil/online . FSC 4210 INCH-POUND A-A-58003E 19 OCT 2010 SUPERSEDING A-A-58003D 23 SEP 2010 COMMERCIAL ITEM DESCRIPTION TRUCK, FIRE FIGHTING (STRUCTURAL, 4x2 OR 4x4) The General Services Administration has authorized the use of t
3、his commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers a structural pumper truck. It has a 4x2 or 4x4 chassis; a diesel engine and automatic transmission; a cab to accommodate at least five seated persons with at least four doors; a 1,250 ga
4、llon per minute (gpm) fire pump; a 500 gallon minimum capacity water tank; utility equipment compartments; and fire hose. The structural pumper truck is intended to combat structural, wildland, urban interface, and similar type fires. 2. SALIENT CHARACTERISTICS. The structural pumper truck shall be
5、in accordance with the applicable requirements of the following chapters of NFPA 1901, Standard for Automotive Fire Apparatus (Current Edition). Chapter Title 1 Administration 2 Referenced Publications 4 General Requirements 5 Pumper Fire Apparatus 12 Chassis and Vehicle Components 13 Low-Voltage El
6、ectrical Systems and Warning Devices 14 Driving and Crew Area 15 Body, Compartments, and Equipment Mounting 16 Fire Pump and Associated Equipment 19 Water Tanks 21 Foam Proportioning Systems 22 Compressed Air Foam Systems 23 Line Voltage Electrical Systems 25 Air Systems Unless otherwise specified (
7、see 6.2), the vehicle shall have a 4x2 chassis. The 4x2 and 4x4 versions shall be identical except for the driveline differences and as otherwise specified herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58003E 2 2.1 Administration. 2.1.1
8、 Environmental conditions. 2.1.1.1 Altitude. Unless otherwise specified (see 6.2), the vehicle, including the pumping system, shall be designed for operation at 2,000 feet above sea level. 2.1.1.2 Temperature range. The tanker shall be capable of satisfactory storage and operation in temperatures ra
9、nging from 0 to 125 F. The tanker shall be equipped with a winterization system that extends the operational range of the tanker. The winterization system shall protect the agent pump, agent piping systems, firefighting systems, and water tank to 0 F. It shall also include the vehicle engine oil and
10、 coolant systems. While in operation, the appropriate systems requiring winterization shall be powered by the tanker. While in storage, the winterization system shall be powered through the electrical shoreline connection (see 2.10.2). 2.1.2 Foreign object damage. All loose metal parts, such as pins
11、 and valve caps, shall be securely attached to the vehicle with wire ropes or chains. “Dog tag“ style beaded chains shall not be provided. Removable panels, if provided, shall be attached with captive fasteners. 2.1.3 Roadability. 2.1.3.1 Operating terrain. The 4x2 vehicle shall operate on paved and
12、 graded gravel roads; the 4x4 version shall also operate on off-road (cross country) terrain. 2.1.3.2 Acceleration. The fully loaded vehicle shall accelerate from 0 to 35 miles per hour (mph) within 25 seconds on a level, paved road. 2.1.3.3 Minimum speed. The fully loaded vehicle shall attain a min
13、imum top speed of 50 mph on a level, paved road. 2.1.3.4 Gradeability. The fully loaded vehicle shall be able to maintain a speed of at least 20 mph while ascending any paved slope up to and including 6.0 percent. The fully loaded vehicle shall also be able to maintain a speed of at least 5 mph whil
14、e ascending any paved slope up to and including 30 percent. 2.1.4 Overall dimensions. Overall dimensions shall be the minimum consistent with the operational performance and the design constraints necessary to achieve the specified performance. Overall dimensions shall not exceed: Length 380 inches
15、Width 96 inches (excluding mirrors) Height 124 inches (4x2) 130 inches (44) 2.1.5 Turning diameter. The fully loaded tanker shall have a wall to wall turning diameter of less than three times the length of the vehicle. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
16、nse from IHS-,-,-A-A-58003E 3 2.1.6 Angles of approach and departure. The fully loaded vehicle shall have angles of approach and departure of not less than 8.0. 2.1.7 Vehicle Stability. Vehicle shall comply with roll over stability criteria as defined by NFPA 1901, paragraph 4.13. 2.1.8 Manuals. 2.1
17、.8.1 Technical manuals. The overall format for the manuals may be military specification, commercial, or a combination of both. Each technical manual shall have a title page. a. The contractor shall validate the technical manuals for accuracy prior to submission to the procuring activity for verific
18、ation. The contractor shall submit one complete set to the procuring activity for verification 30 days before the first production inspection. Any changes or corrections noted by the procuring activity shall be corrected and updated pages or manuals shall be submitted to the procuring activity. b. O
19、nce approved by the procuring activity, the contractor shall pack two complete sets of technical manuals with each vehicle. An additional two complete sets shall be submitted to the procuring activity for stock. c. Once approved by the procuring activity and a Technical Order number is assigned, the
20、 contractor shall pack two complete sets of both hard copy and CDs with each vehicle and one complete set of both hard copy and CDs shall be submitted to the procuring activity for stock. The procuring activitys address will be provided. d. The contractor shall grant the United States Air Force a no
21、n-exclusive, non-assignable, royalty free U.S. Government (Government) Purpose License, to scan into CENTRA (the USAF repository) and to reproduce and distribute (either electronically or via hard medium) copies or facsimiles of manuals produced and distributed by the contractor for this CID. These
22、rights extend to Government agencies only, and the data contained in the technical manuals is not to be sold, disclosed or otherwise provided to any other entity or entities outside the Government. The license shall remain in effect as long as the vehicles described in the required technical manuals
23、 remain under Government control and usage. In addition, the contractor shall grant permission for the Government to place an Air Force TO (Technical Order) number and publication date as well as distribution, warning, handling and destruction statements on the cover / title pages of the TO. 2.1.8.1
24、.1 Operators manuals. The operators manual shall include all information required for the safe and efficient operation of the vehicle, including the fire extinguishing equipment, and any special attachments or auxiliary equipment. The operators manual shall include at least the following: a. Locatio
25、n and function of all controls and instruments shall be illustrated and fully described. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58003E 4 b. Safety information that is consistent with the safety standards established by the Occupational S
26、afety and Health Administration (OSHA). c. Checks and adjustments in preparation for placing the vehicle for service upon receipt from the contractor. d. Preparation for shipment or storage. e. Warranty information and period of the warranty for the complete vehicle and for any component warranty th
27、at exceeds the warranty of the complete vehicle. Addresses and telephone numbers shall be provided for all warranty providers. f. General description of and step-by-step instructions for the operation of the vehicle and its fire extinguishing system(s) and auxiliary equipment. g. Description of the
28、post-operational procedures (draining, flushing, et cetera). h. Checklists for the daily maintenance inspection and mission readiness checks that the operator is expected to perform. i. Procedures for towing a disabled vehicle. j. Schedules for required preventative maintenance and required periodic
29、 maintenance. 2.1.8.1.2 Service manuals. The service manual shall identify any special tools and test equipment required and shall cover troubleshooting and maintenance as well as minor and major repair procedures. T he text shall contain performance specifications, tolerances, and fluid capacities;
30、 current, voltage, and resistance data; test procedures; and such illustrations and exploded views as may be required to permit proper maintenance by qualified mechanics. The manual shall contain an alphabetical subject index as well as a table of contents. The service manual shall contain at least
31、the following, where applicable: a. Fire fighting system schematic(s). b. Hydraulic schematic. c. Pneumatic schematic. d. Electrical schematic. e. Winterization schematic. f. Schedules for required preventative maintenance and required periodic maintenance. g. Location, procedure, and interval for p
32、arts of the truck and equipment which require lubrication. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58003E 5 2.1.8.1.3 Parts manual. The parts manual shall include illustrations and exploded views, as needed, to properly identify all parts
33、, assemblies, subassemblies, and special equipment. All components of assemblies shown in illustrations or exploded views shall be identified by reference numbers which correspond to the reference numbers in the parts lists. All purchased parts shall be cross-referenced with the original manufacture
34、rs name and part number. The parts identification manual shall provide the description, length, dimensions, and quantity of each item used per vehicle. The manual shall contain a numerical index. The parts manual shall contain a list of all of the component vendor names, addresses, and telephone num
35、bers referenced in the parts list. 2.1.9 Painting, plating, and corrosion control. 2.1.9.1 Dissimilar metals. Dissimilar metals, as defined in MIL-STD-889, shall not be used in intimate contact with each other. 2.1.9.2 Finish. Exterior surfaces shall be prepared, primed, and painted with polyurethan
36、e paint in accordance with all of the paint manufacturers instructions and recommendations. Unless otherwise specified (see 6.2), the exterior finish color shall be Candy Apple Red, Sikkens Color Number FLNA3021, DuPont Color Number 97902U or 4737U, PPG Color Number 71528 (the PPG name for this colo
37、r is Cardinal Red), or equal. When specified, the exterior finish color shall be Desert Sand, Color Number 30313 of FED-STD-595. a. For vehicles painted Candy Apple Red, the cab upper body (from the bottom of the windshield) and roof shall be painted White, Color Number 17875 of FED-STD-595. Compart
38、ment interiors shall have a standard commercial finish. All bright metal and anodized parts, such as mirrors, horns, light bezels, and treadplate, shall not be painted. Roll-up compartment doors may be painted or unpainted. b. For vehicles painted Desert Sand, all exterior surfaces, excluding all no
39、rmally bright metal and anodized parts and any interior surfaces visible with any compartment door open (but not the interior of the cab), shall be painted body color. This includes compartment shelves and mounting hardware, but does not include items mounted in the compartments. Non-metallic materi
40、als may be black or gray. 2.1.9.3 Horizontal Reflective striping. Horizontal reflective striping in accordance with NFPA 1901 shall be applied around the vehicle in an approximate plane with the headlights. Bright metal trim or anodized parts may interrupt the reflective stripes. The pattern shall b
41、e 10 inches wide with three reflective stripes (one inch reflective, one inch body color, six inches reflective, one inch body color, and one inch reflective). The reflective stripes shall be white for vehicles painted Candy Apple Red and Desert Sand. 2.1.9.4 Chevron Striping. In accordance with 15.
42、9.3.2 of NFPA 1901 at least 50 percent of the rear-facing vertical surfaces, visible from the rear of the apparatus, excluding any pump panel areas no-t covered by a door, shall be equipped with retroreflective striping in a chevron pattern sloping downward and away from the centerline of the vehicl
43、e at an angle of 45 degrees. 3M part number 983-17 (red) and 983 -23 (florescent yellow/green) reflective diamond grade or equivalent shall be utilized. Each stripe in the chevron shall be a single color alternating between red and fluorescent yellow in accordance with 15.9.3.2.1. Each stripe shall
44、be 6-inches (150 mm) in width in accordance with 15.9.3.2.2 of NFPA 1901 and the example provided below. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58003E 6 2.1.9.5 Lettering. Vehicles painted Candy Apple Red shall have the letters UNITED ST
45、ATES and AIR FORCE applied in synthetic or encapsulated gold leaf, with outline and black shadow, on the front door on both sides in long radius elliptical arches above and below the lettering center line. The size of the lettering shall be a minimum of 2-inches to a maximum of 6-inches. Vehicles pa
46、inted Desert Sand shall have no lettering. 2.1.10 Identification plate. A permanently marked identification plate shall be securely mounted at the drivers compartment. The identification plate shall contain the following information: a. NOMENCLATURE b. MANUFACTURERS MAKE AND MODEL c. MANUFACTURERS S
47、ERIAL NUMBER d. USAF VEHICLE REGISTRATION NUMBER e. NATIONAL STOCK NUMBER (NSN) f. VEHICLE CURB WEIGHT: kg (pounds) g. PAYLOAD, MAXIMUM: kg (pounds) h. GROSS VEHICLE WEIGHT (GVW): kg (pounds) i. FUEL CAPACITY AND TYPE: gal (gallons) / L (liters) j. DATE OF DELIVERY (month and year) k. WARRANTY (mont
48、hs and km (miles) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58003E 7 l. CONTRACT NUMBER m. PAINT COLOR AND NUMBER n. LENGTH, WIDTH, AND HEIGHT OF VEHICLE IN INCHES AND CENTIMETERS. 2.2 General requirements. 2.2.1 Hose storage. 2.2.1.1 Hose
49、storage area. The vehicle shall have a hose bed, with a removable and secured hose bed cover and two adjustable dividers, capable of carrying 1,000 feet of 5-inch hose and 800 feet of 3-inch hose. 2.2.1.2 Speed lay hose beds. The vehicle shall have two speed lay hose beds with one or more removable and secured hose bed covers. Hose bed covers will be red for vehicles painted Candy Apple
