1、 - MIL-J-83382C 84 H 777770b OLIO8770 I MIL- J-83382C -. -30 October 1981 SUPERSEDING 2 May 1978 MIL-J-83382B(USAF) MIL ITA RY SPECIFICATION beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: ASD/E
2、NESS, bright-Patterson AFB, OH 45433,by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. JACKET, FLYERS, ISiEN S, SuMM3R, PIRE RESISTANT, CWD-36/P This specification is approved for use by all Bepartments and Ag
3、encies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification coversonetype of flight jacket. The jacket is designated ClvU-36/P. 1.2 Sizes. specified (see 6.2) : . The jacket shall be furnished in one of the following sizes as Small 34 - 36 Medium 38 - 40 Large 42 - 44 Extra large 46
4、- 48 Extra extra large 50 - 52. 2. APPLICABLE BOCUPIENTS 2.1 Government documents * 2.1.1 Specifications, standards. and drawinm. Unless otherwise specified, the following specifications, standards, and drawings of the issue listed in that issue of the Department of Defense Index of Specifications a
5、nd Standards (DODISS) specified in the solicitation form a part of this specification to the extent specified herein. SPE C1 Pl CATIOIUS FED BR AL Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- -. _ _ MIL-J-83382C 84 W 777770b 0408773 3 MIL-J-83382
6、C PPP-T-45 MILITARY MlL- c- 37 3 5 MIL-k-56 6 4 NIL-F-2 184 O MIL-C-8 18 14 MIL-T-83 19 3 MIL- C-83242 MIL- C-83 450 STANDARDS FEDERAL FED-STD-4 FED-STD-191 PED-STD-75 1 MILITARY MIL-STD-105 MIL-STD-129 DRALINGS AIR FORCE 70238 70239 70240 7024 1 70242 70243 Tape, Gummed, Paper, Reinforced. and Plai
7、n, for Sealing and Securing Cuffs, Knit, Irist and Ankle; and Cloth, Knitted Webbing, Textile, Elastic, Cotton Fastener Tapes, hook and Pile, Synthetic Cloth, Twill, Aramid, High Temperature Resistant Thread, Aramid, Spun Staple Cord, Aromatic Polyamide, Nonmelting Cloth, Meta-Aramid harp, Meta-Aram
8、id/Para-Aramid Filling, Meta-Aramid/Novoloid Filling, Napped Glossary of Fabric Imperfections Textile Test Methods Stitches, Seams, and Stitchings Sampling Procedures and Tables for Inspection by Attributes Marking for Shipment and Storage Patterns, Jacket, Flying, Mens, Summer, Fire Resistant, CW-3
9、6/P, kiscellaneous, All Sizes Patterns, Jacket, Flying, Summer, Fire Resistant, CkU-36/P, Size Small Patterns, Jacket, Flying, Mens, Summer, Fire Resistant, CWU-36/P, Size Medium Patterns, Jacket, Flying, kens, Summer, Fire Resistant, CWU-36/P, Size Large Patterns, Jacket, Plying, Piens, Summer, Fir
10、e Resistant, CWU-36/P, Size Extra Large Patterns, Jacket, Flying, Mens, Summer, Fire Resistant, CWU-36/P, Size Extra Extra Large (Copies of specifications, standards, and drawings required by manufacturers in connection with specific acquisition functions should be obtained from the contracting acti
11、vity or as directed by the contracting officer.) * 2.1.2 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. Provided by IHSNot for ResaleNo reproduction or networking permitted
12、without license from IHS-,-,-MIL- J-83382C 3. REQUIREMENTS 3.1 Materials . 3.1.1 1120 Avenue of the Americas; New York, New York 100361, or equal. a 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-VIL-J-83382C 89 777770b OLIO8773 7 I MI L-J- 83382C
13、 TABLE r. Slide fasteners. Application for Slide Fastener Size small jacket Front op en in g Cigarette and pencil pocket Size medium j acket Front opening Cigarette and pencil pocket Size large jacket Front opening Cigarette and pencil pocket Size extra large jacket Front opening Cigarette and penci
14、l pocket Size extra extra large jacket Front opening Cigarette and pencil pocket IV I IV I IV I IV I IV I cation V-F- 106 Style size- - 8 iM 3 IM 8 IM 3 #M I 8 jM 3, !M Length (Inches) .-_-_- 21 4-3/4 21-1/2 4-3/4 22 4-3/4 22- 1/2 4-3/4 23 4- 3/4 TABLE 1.1. Width of waistband material. -,-._-._I_ _I
15、_-.-_-_ -_ - Width (Inches) in Direction of- Courses of Material - 1/ 1 - - _. Size of Jacket Small Medium Large Extra large Extra extra ,arge 24 25 26 27 28 - - i/ A tolerance of plus or minus 1/2 inch will be permitted. . The jacket shall be lined, shall be single breasted, shall have a * bias-cut
16、 3:2 -$ ack, and shall have a straight center front opening with a slide fastener closure, left sleeve and two front (patch) pockets that have envelope storm flaps. cigarette and pencil pocket shall have a bellows-style cigarette compartment with a covered vertical slide fastener closure, on the for
17、ward side, the full length of the pocket and four pencil compartment openings, two upper and two lower. Closure of the flaps of the front pockets shall be effected with hook and pile fastener tape. sleeve and shall have a knitted waistband. The jacket shall have a cigarette and pencil pocket on the
18、The The jacket shall have a knitted wristlet on each 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-83382C Bq W 777790b 0408774 7 MIL- J - 8 3 3 8 2 C 3.3 Construction. The iacket shailbe constructed in accordance with table III; however, th
19、e manufacturer will not be required to follow the exact sequence of operations as listed therein. 3.3.1 Stitches, seams, and stitchings. Stitches, seams, and stitchings used in the construction of the jacket shall conform to FED-STD-751 Wherever two or more methods, seams, or stitchings are specifie
20、d for the same operation, any one of them may be used. allowances shall be maintained so that raw edges, run-Offs, twists, pleats, puckers, or open seams will not result. that there will be no tight or loose tension. The looper thread (under thread) of stitch type 401 shall be on the inside of the j
21、acket. All seams shall start and finish evenly. Seam Thread tension shall be maintained so * 3.3.1.1 Thread breaks and ends of seams. Thread breaks (all stitch types) shall be secured by stitching back of each end not less than 1/2 inch. stitches or thread breaks of stitch type 401 may be repaired u
22、sing stitch type 301. 301, if not caught in other seams or stitchings, shall be backstitched not less than 1/4 inch. labels) shall be overlapped not less than 1/2 inch. the labels shall be overlapped not less than three stitches. Skipped The ends of all seams or stitchings that are produced with sti
23、tch type The ends of a continuous line of stitching (except on the The ends of stitching on 3.3.1.2 Sewing tolerances. A tolerance of plus or minus 1/16 inch will be permitted for 1/4-inch-gage and 5/16-inch-gage stitching. O or minus 1/8 inch will be permitted for 3/8-inch-gage stitching. of plus o
24、r minus 1/16 inch will be permitted for raise seam 1/4-inch gage. tolerance of plus 1/32 or minus O inch will be permitted for stitching 1/16 inch from the edge. Unless otherwise specified herein, a tolerance of plus or minus 2 stitches per inch will be permitted for stitches per inch, 3.3.2 fastene
25、r covers shall have a cord beading. slide fastener closures shall be flush with the slide fastener scoops. scoops, when locked together, shall be completely concealed by the beaded covers. A tolerance of plus A tolerance A Corded beading in slide fastener covers, The edges of the slide The outer bea
26、ded cloth edges of the The * 3.3.3 Cutting. The jacket shall be cut from the materials specified herein in accordance with the pattern parts that are listed in table IV. 3.4 Patterns. and shape to the applicable patterns referenced on Drawings 70238 through 70243. allowance of 1/2 inch. The manufact
27、urers working patterns shall be identical in size Unless otherwise specified on the drawings, the patterns provide a seam 3.5 Finished measurements. The finished measurements of the jacket shall conform to table V. The finished measurements of the jacket shall be. taken as follows: Measure the back
28、length, at the center of the back, from the bottom of the undercollar seam to the bottom above the knit. the base of the armhole, with the slide fastener closed, from folded edge to folded edge. armhole to the seam above the knit. Measure the 1/2 chest at Measure the sleeve inseam, along the underar
29、m seam, from the 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-83382C H H H w Ll a 2 6i hh goo * * * 6 .A . . . - .- _*I -.JI Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c O *rl cr (d L
30、a, a O r, O Fi *rl cr a 4 L o v) a, R v) cr k (d g -I cr o a, r, a, a L O a a, 3 a a, o (d rl a, O z MIL-J-83382C 4 9999906 0408776 2 I v) v) O CI 4 a a I-I aa, cc (de rn * * * (u * MIL- 5-83 3 82 C 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-h
31、IL-J-83362C a a, 3 El *rl cr u 8 1 (u 7 Cu .- Q ao a aa, K! .ri * * * * * Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-83382C 84 777770b 0408778 b MIL- 5-83 382 C Cu T- a tus- ? T- M O O a, c, (d rl 8 (d c F O k a, m c, F a, C a, c, o KI 4-i
32、 c *rl c; 1 In o * * * I 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - _ - I_- MIL-J-83382C 84 - 9777906 0408779 - kIL- J-83 3 82 C .rl c, (d a, a O G-4 O c O *li cr a .rl k o VI a, CiI - O 2 (u r (u r (u r A Co v) A kl w A v3 03 O v) Iw i- r
33、.- r O O O O m M M rn “E: o .rl (d ha, c cru ?+, O0 c a *rl a, (dc rlc, rlw %I O0 * * * * * 10 i- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-3382C 4 m 7779906 0408780 4 m MIL- J-83382C (u F (u r (u r- O M r- - r O O O M M M ho rl e 0 c .ri
34、 Cu 8 = O c, a M a, sl 4 rl (d 5 2 4: c, L (d a, c n H a, 4J O z * * Y 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL- 3-63 382 C Cu 7 Cu r 7 I (d v) v) n id Cu v) 4 U (s F s. ro a a *a, (64: ho kC a, (d .rl cari LI O a, id o c, *ri 3 12 Prov
35、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.- MIL-J-83382C 4 m 797770b 0408782 8 m MIL-J-83382C E: O -rl c, a, a O % O c O *rl s a .rl k o m 0 FI 21 O 2l - n o N I cr v) CI W n n P W N N (u N I I I I o o cr cr cn cg cn cn CI CI ILI J (d W n W (d Cu
36、I o .rl c, c O u I ?i H H H w LI 4 E-l a c O .rl c, (d a O (H O O *I+ c, a *rl k o ro Q) Gl % c - O 2 - (u r- (u (u T T (u T (u F- 2 In cn cn P n n P (d (u (u cn cn J J v W (s (s n (d (u I a cn cn v cv I a cri w n (d cv I 6 CA J v k e. O O e k O O Y O M 7- O0 M=? a, e c, a, hoc cc, k Q) ho e 3 a, k
37、5 ex 1; Ln r- 3 7 * * 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L - MIL-J-83382C AL( m 77777Ob 040878b 5 m MIL- J-83 382 C 2 N le size. Lot Size (Units) Isampie I Size 800 or less I 2 1 f I 801 to 22,000 inclusive i 3 22,001 or more 4.2.2 En
38、d item. The end item shall be examined as specified in 4.2.2.1 and 4.2.2.2. The sample unit for these examinations shall be one jacket. 4.2.2.1 Visual examination. The end item shall be visually examined for defects. The inspection level for this visual exam nation shall be II of MIL-STD-105. The ac
39、ceptable quality level for this visual examination shall be 2.5 defects per 100 units (dhu) for major defects, 5.0 dhu for major and minor A defects, and 40.0 dhu for major and minor A and B defects. The defects found during this visual examination shall be classified as specified in table VII. * 4.
40、2.2.2 Examination of finished measurements. The end item shall be measured as specified in 3.5. The inspection level for the examination of the finished measurements shall be S-3 of MIL-STD-105. The acceptable quality level for the examination of the finished measurements shall be 4.0 dhu for defect
41、s (one class). finished measurement specified in table V shall be classified as a finished measurement defect. as a finished measurement defect. Each finished measurement of the end item that deviates from the Sleeve lengths uneven 1/2.inch or more shall be classified * 4.3 Examination of preparatio
42、n for delivery. Shipping containers fully prepared for delivery shall be examined, for the defects listed in table VIII, to determine compliance with the packaging, packing, and marking requirements that are specified herein. The sample unit for this examination shall be one shipping container fully
43、 prepared for delivery. The lot size shall be the number of shipping containers in the end item inspection lot. The inspection level shall be S-2 of MIL-STD-105. The acceptable quality level shall be 2.5 dhu for defects (one class). 5. PACKAGING 5.1 Preservation and packaging. Preservation and packa
44、ging shall be level A or C as specified (see 6.2). 5.1.1 Level A. Each jacket shall be folded to approximately 20 inches by 16 inches. Four folded jackets shall be placed in a box that conforms to type CF, class domestic, style RSC, minimum bursting strength of 200 pounds per square inch of PPP-6-63
45、6. The outside dimensions of the box shall be approximately 20 inches by 16 inches by 6 inches. The box shall be closed by applying tape that conforms to PPP-T-45. 5.1.2 Level C. The jacket shall be packaged one per unit container in accordance with the manufacturers commercial practice. 26 Provided
46、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL- J-83 382 C TABLE VII. Classification of defects. i Defect 3artacks )ne bartack missing, insecure, or misplaced not serving mtended purpose Cwo bartacks missing, insecure, or misplace not serving intended p
47、urpose rhree or more bartacks missing, insecure, or misplaced lot serving intended purpose 4ny bartack less than specified length or width 31 eannes s indelible ink shade stamping exposed on outside or spots or stains of permanent nature Removable spot or stain clearly noticeable rhread ends not tri
48、mmed or one or more shade ticket not remo ved ComDonent and assembly Any component defective Any component missing Any required operation omitted or improperly performed Cutting Any component not cut in accordance with directional lines on patterns or specified requirements Material defects and workmanshiD damanes Any weakening material defect such as hole, cut, tear, smash, burn, multiple float, large drill hole, or needle chew that might.develop into hole Outside of jacket containing fuzz balls; slubs or knots (exceeding limits shown
