1、Performance Requirements for Temperature Actuated, Flow Reduction (TAFR) Valves for Individual Supply FittingsASSE InternationalASSE Standard #1062-2017ASSE Board Approved: October 2017ANSI Approved: September 2017 ICS Code: 23 060 99An American National StandardTemperature Actuated, Flow Reduction
2、(TAFR) Valves for Individual Supply Fittings iASSE Standard #1062-2017ASSE InternationalMokena, IllinoisCopyright 2017, 2006, 1997All rights reserved.Neither this standard, nor any portion thereof, may be reproduced without the written consent of ASSE International.No product may be said to be liste
3、d by ASSE unless the manufacturer has applied to ASSE International, has had its product tested by an official ASSE recognized independent laboratory according to the applicable standards, and had its documentation reviewed and approved by the consensus ASSE Seal Control Board. Having completed the
4、aforementioned, the manufacturer may display the ASSE seal on the product. Instructions for receiving the authorization to display the Seal are available from the ASSE International office. Organizations wishing to adopt or list any ASSE standard should print the ASSE standard number on the cover pa
5、ge first in equal or larger type to that of the adopting or listing organization.General Informationii Temperature Actuated, Flow Reduction (TAFR) Valves for Individual Supply Fittings ASSE Standard #1062-2017Temperature Actuated, Flow Reduction (TAFR) Valves for Individual Supply Fittings iiiASSE S
6、tandard #1062-2017This foreword shall not be considered a part of the standard; however, it is offered to provide background information.Exposure to high temperature water can result in serious injuries. This problem has been publicized by consumer safety organizations and is addressed in ASTM F444-
7、88, Standard Consumer Specification for Scald-Preventing Devices and Systems in Bathing Areas.This standard covers point of use temperature actuated, flow reduction (TAFR) valves that are installed in-line with, or integrated into, supply fittings. These valves automatically reduce discharge flow to
8、 a trickle if water temperature exceeds a preset limit. Other ASSE standards, such as ASSE 1016/ASME A112.1016/CSA B125.16, ASSE 1017, ASSE 1066, ASSE 1069, and ASSE 1070/ASME A112.1070/CSA B125.70, have been developed for hot and cold water mixing valves that limit discharge temperature, and in-lin
9、e pressure balancing valves that minimize pressure variations between the hot and cold water supplies. TAFR valves are not intended to be installed in place of devices complying with ASSE 1016/ASME A112.1016/CSA B125.16, ASSE 1017, ASSE 1066, ASSE 1069, or ASSE 1070/ASME A112.1070/CSA B125.70. ASSE
10、recommends that TAFR valves be installed in accordance with local code requirements by qualified individuals.Recognition is made of the time volunteered by the working group members who participated in the revision process, and of the support of manufacturers. This standard does not imply ASSEs endo
11、rsement of a product that conforms to these requirements.Compliance with this standard does not imply acceptance by any code body.Forewordiv Temperature Actuated, Flow Reduction (TAFR) Valves for Individual Supply Fittings ASSE Standard #1062-2017Edward J. Lyczko, ChairpersonCleveland Clinic Retiree
12、 Cleveland, OHWilliam Briggs, Jr.MGJ AssociatesNew York, NYTerry BurgerNSF InternationalYpsilanti, MIWilliam ChapinProfessional Code Consulting, LLCCullman, ALMark FishZurn Industries, LLCCary, NCRon GeorgePlumb-Tech Design b) Model number of the device; andc) Maximum actuation temperature for which
13、 the device is designed.4.3.2 The packaging or installation instructions for a device that is not integrated into a supply fixture shall include the following information.a) Maximum rated working pressure;b) Nominal device size; c) Direction of flow;d) Fitting classification (e.g. Bathtub, Bidet, et
14、c.) for acceptable applications, per section 1.2.3(b); ande) Minimum flow rate prior to actuation.4.3.3 Each device that is integrated into a supply fixture shall have the following information marked on the installation instructions for the supply fitting:a) Manufacturers name or trademark;b) Model
15、 number of the device; andc) Maximum actuation temperature for which the device is designed.4.3.4 Each device that is integrated into a supply fixture shall have the following information marked on the packaging of the supply fitting:a) Indication that the supply fitting contains a temperature actua
16、ted flow reduction valve; and b) Maximum actuation temperature for which the device is designed.4.3.5 The markings on the device shall be either etched, cast, molded, stamped, or engraved on the body of the device or on a corrosion resistant plate securely attached to the valve with a corrosion resi
17、stant means.10 Temperature Actuated, Flow Reduction (TAFR) Valves for Individual Supply Fittings ASSE Standard #1062-20174.4 Installation Instructions4.4.1 Complete instructions for installation shall be packaged with the device, except when integral to a fitting assembly. Drawings or schematic sket
18、ches that would be useful to the installer shall be part of these instructions. These instructions shall provide all information necessary for correct installation.4.4.2 The installation instructions shall indicate the tested and approved installation position of the device.4.5 MaintenanceComplete i
19、nstructions shall be furnished for field maintenance and field repair.4.6 Field TestingManufacturers recommendations for field testing shall be furnished.Temperature Actuated, Flow Reduction (TAFR) Valves for Individual Supply Fittings 11ASSE Standard #1062-2017Section V5.0 DefinitionsDefinitions in
20、 the standard shall take precedence over any other publication. Definitions not shown are found in the Plumbing Dictionary (Sixth Edition) published by ASSE International.ASSE International Chapter of IAPMO, LLC18927 Hickory Creek Drive, Suite 220 Mokena, Illinois 60448Phone: 708.995.3019 Fax: 708.479.6139 http:/www.asse-plumbing.org
