1、AN AMERICAN NATIONAL STANDARD ASME Y14.34-2013(Revision of ASME Y14.34-2008)Associated ListsEngineering Drawing and Related Documentation PracticesASME Y14.34ADOPTION NOTICEASME Y14.34, Associated Lists, was adopted on 1 August 2008 for use by the Department of Defense, (DoD).Proposed changes by DoD
2、 activities must be submitted to the DoD Adopting Activity: Commander, U.S. ArmyARDEC, ATTN: RDAR-QES-E, Picatinny Arsenal, NJ 07806-5000. Copies of this document may be purchased fromThe American Society of Mechanical Engineers (ASME), 22 Law Drive, P.O. Box 2900, Fairfield, NJ 07007-2900;http:/www
3、.asme.org.Custodians: Adopting Activity:Army AR Army ARNavy SA (Project DRPR-2014-001)Air Force 16Review Activities:Army AV, CR, PT, TE, TMNavy AS, CG, CH, EC, MC, SAAir Force 04, 11, 13, 16, 99DLADHOSDSENSANSOther MP, DC2NOTE: The activities listed above were interested in this document as of the d
4、ateof this document. Since organizations and responsibilities can change, youshould verify the currency of the information above using the ASSIST Onlinedatabase at https:/assist.dla.mil.ASMC N/A AREA DRPRDISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited.ASME Y14.34-201
5、3(Revision of ASME Y14.34-2008)Associated ListsEngineering Drawing and RelatedDocumentation PracticesAN AMERICAN NATIONAL STANDARDTwo Park Avenue New York, NY 10016 USADate of Issuance: May 16, 2014This Standard will be revised when the Society approves the issuance of a new edition.Periodically cer
6、tain actions of the ASME Y14 Committee may be published as Cases. Cases arepublished on the ASME Web site under the Y14 Committee Page at go.asme.org/Y14committee asthey are issued.Errata to codes and standards may be posted on the ASME Web site under the Committee Pages toprovide corrections to inc
7、orrectly published items, or to correct typographical or grammatical errorsin codes and standards. Such errata shall be used on the date posted.The Y14 Committee Page can be found at go.asme.org/Y14committee. There is an option availableto automatically receive an e-mail notification when errata are
8、 posted to a particular code or standard.This option can be found on the appropriate Committee Page after selecting “Errata” in the “PublicationInformation” section.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures a
9、ccredited as meeting the criteria for American NationalStandards. The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate. The proposed code or standard was madeavailable for publi
10、c review and comment that provides an opportunity for additional public input from industry, academia,regulatory agencies, and the public-at-large.ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity.ASME does not take any position with respect to the
11、 validity of any patent rights asserted in connection with anyitems mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent, nor assumes any such liability. Users of a code or standard are expresslyad
12、vised that determination of the validity of any such patent rights, and the risk of infringement of such rights, isentirely their own responsibility.Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted asgovernment or industry endorsement o
13、f this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies, which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an elect
14、ronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersTwo Park Avenue, New York, NY 10016-5990Copyright 2014 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.CONTENTSForeword ivCommittee
15、Roster . vCorrespondence With the Y14 Committee vi1 General 12 References . 23 Definitions . 34 Common Requirements for Associated Lists 55 Parts List Preparation. 66 Application List Preparation . 77 Data List Preparation . 78 Index List Preparation 89 Wire List Preparation . 8Figures3-1 Applicatio
16、n List Manually Generated Format 93-2 Application List Digitally Generated Format . 103-3 Data List Manually Generated Format . 113-4 Separate Data List Digitally Generated Format 123-5 Index List Manually Generated Format 133-6 Separate Index List Digitally Generated Format . 143-7 Separate Parts L
17、ist Manually Generated Format . 153-8 Separate Parts List Digitally Generated Format 163-9 Wire List Manually Generated Format . 173-10 Wire List Digitally Generated Format . 184-1 Separate List Heading . 195-1 Integral Parts List Graphic Sheet of Drawing 205-2 Integral Parts List Separate Sheet of
18、Drawing 215-3 Parts List Column Entries . 226-1 Application List Column Entries . 247-1 Data List Column Entries 248-1 Index List Column Entries . 259-1 Wire List Column Entries 26iiiFOREWORDThis Standard establishes the requirements for associated lists and ties them together with theengineering dr
19、awing and related documentation practices in the Y14 series. It is not the intentofthis Standardtobe astand-alonedocument. Anaccurateperception ofassociatedlists practicesis derived by treating ASME Y14.34, ASME Y14.100, ASME Y14.24, and ASME Y14.35 as acomposite set.This Standard is a revision of A
20、SME Y14.34-2008, Associated Lists. Changes contained in thisrevision are intended to improve standardization and harmonize practices and methodologybetween industry and government.The successful revision of this Standard is attributed to the subcommittee members and theirrespective companies, and th
21、e department and agencies of the U.S. government.Suggestions for improvement of this Standard are welcome. They should be sent to TheAmerican Society of Mechanical Engineers, Secretary, Y14 Standards Committee,Two Park Avenue, New York, NY 10016-5990.The following is a summary of the significant cha
22、nges incorporated in this revision:Reformatted the Standard to add 1.2 ASME Y14 Series Conventions in its entirety, to renum-ber the figure numbers, and to renumber accordingly due to the reformatting.Section 2 Renamed and updated.Section 3 Definitions.(a) added definition for Deletion List(b) added
23、 definition for Field of Drawing(c) added definition for Product Data Management (PDM) System(d) added definition for Salvage List(e) updated definitions duplicated from other standards as applicableParas. 4.1.1 and 4.1.2 revised to include stipulations regarding the use of PDM systems.Para. 4.7 rev
24、ised to clarify list identifiers and to associate specific prefixes to respectivelists.Para. 5.3.2(b)(5) added NOTE that adds the requirement for entering a dash or the abbre-viation REF in QTY REQD columns when listing reference drawings or documents in aparts list.Para. 5.3.3 added to address the
25、use of deletion lists and salvage lists for modificationand kit drawings.Addressed DoD comments deferred from the last revision.Clarified Design Activity Identification (DAI) requirements/examples in Figs. 4-1, 5-3, 7-1,and 8-1.This revision was approved as an American National Standard on November
26、8, 2013.ivASME Y14 COMMITTEEEngineering Drawing and Related Documentation Practices(The following is the roster of the Committee at the time of approval of this Standard.)STANDARDS COMMITTEE OFFICERSF. Bakos, Jr., ChairW. A. Kaba, Vice ChairF. Constantino, SecretarySTANDARDS COMMITTEE PERSONNELA. R.
27、 Anderson, Dimensional Dynamics, LLCF. Bakos, Jr., ConsultantJ. V. Burleigh, UnaffiliatedF. Constantino, The American Society of Mechanical EngineersD. E. Day, TEC-EASE, Inc.K. Dobert, Siemens PLM SoftwareB. A. Harding, Purdue UniversityD. H. Honsinger, ConsultantW. A. Kaba, Spirit AeroSystems, Inc.
28、A. Krulikowski, Effective Training, Inc.SUBCOMMITTEE 34 ASSOCIATED LISTSR. D. Green, Chair, The Boeing Co.L. G. Davis, UnaffiliatedB. Germany, Raytheon Co.C. N. Markt, Lockheed Martin Aeronautics Co.G. M. Nelson, UnaffiliatedvE. F. McCarthy, Raytheon Missile SystemsP. J. McCuistion, Ohio UniversityJ
29、. D. Meadows, James D. Meadows Order Department: 22 Law Drive, P.O. Box 2900, Fairfield, NJ 07007-2900 (www.asme.org)3 DEFINITIONS3.1 Alphanumeric Arrangementalphanumeric arrangement: an ordered grouping of symbols, numbers, and letters used to form an identification.3.2 Application Dataapplication
30、data: the next assembly(ies), and the model number, nomenclature, or equivalent designator of theassembled unit(s), of which a part or assembly is a component.3.3 Application Listapplication list: application data presented in a separate list. See Figs. 3-1 and 3-2.3.4 Approvalapproval: an indicatio
31、n that the document meets requirements for preparation and content. See Fig. 4-1.3.4.1 Approval Indicatorapproval indicator: any symbol adopted by the design activity to indicate approval (ASME Y14.100).3.5 Associated Listassociated list: a tabulation of engineering information pertaining to an item
32、 depicted on an engineering drawingor by a set of drawings, e.g., application list, data list, index list, parts list, and wire list.3.6 Bulk Itemsbulk items: those constituents of an assembly or part, such as oil, wax, solder, cement, ink, damping fluid, grease,flux, welding rod, twine, or chain, t
33、hat satisfy one or more of the following criteria:(a) the quantity required cannot readily be predetermined(b) the physical nature of the material is such that it is not adaptable to pictorial representation(c) the finished size is obtainable through use of such tools as shears, pliers, or knives, w
34、ithout further machiningoperation(d) thefinalconfigurationissuchthatitcanbedescribedinwritingwithoutthenecessityofpictorialrepresentation(ASME Y14.100).3.7 Commercial and Government Entity (CAGE) Codecommercial and government entity (CAGE) code: a five-character code that provides a unique activity
35、identifier usedby the government for activity identification (ASME Y14.100).3.8 Data Listdata list: a tabulation of all engineering drawings, associated lists, specifications, standards, subordinate data listsand nonbracketed in-house documents necessary to meet the technical design disclosure requi
36、rements. See Figs.3-3 and 3-4.3.9 Deletion Listdeletion list: a tabulation of items to be removed and not reinstalled.3.10 Design Activitydesign activity: an organization that has, or has had, responsibility for the design of an item (ASME Y14.100).3.10.1 Current Design Activitycurrent design activi
37、ty: the design activity currently responsible for the design of an item. This may be the originaldesign activity or a design activity to which the design responsibility has been transferred (ASME Y14.100).3ASME Y14.34-20133.10.2 Original Design Activityoriginal design activity: the design activity o
38、riginally responsible for the design and identification of an item, whosedrawing number and activity identification is shown in the title block of the drawings and associated documents(ASME Y14.100).3.11 Design Activity Identification (DAI)design activity identification (DAI): the application of a u
39、nique identifier that distinguishes an activity or organizationfrom another activity or organization. Examples of activity identification include activity name, activity name andaddress, or CAGE code (ASME Y14.100).3.12 Digital Datadigital data: data stored on a computer system that employs a displa
40、y on which the user and the computer interactto create or alter entities for the production of layouts, drawings, numerical control tapes, or other engineeringdata (ASME Y14.100).3.13 Documentdocument: a term applicable to the specifications, drawings, lists, standards, pamphlets, reports, and print
41、ed,typewritten, or otherwise created information relating to the design, procurement, manufacture, testing, or accept-ance inspection of items or services (ASME Y14.100).3.14 Drawingdrawing: an engineering document or digital data file(s) that discloses, directly or by reference, by means ofgraphic
42、or textual presentations, or by combinations of both, the physical or functional requirements of an item(ASME Y14.100).3.15 Engineering Dataengineering data: engineeringdocumentssuchasdrawings,associatedlists,accompanyingdocuments,specifications,standards, or other information prepared or used by a
43、design activity and relating to the design, manufacture,procurement, testing, or inspection of items (ASME Y14.100).3.16 Field of Drawingfield of drawing: the area of a drawing that contains the product definition of an item (ASME Y14.100).3.17 Find Number or Item Numberfind number or item number: a
44、 reference number assigned to designate an item on the field of the drawing, in lieuof using the items part or identifying number. It is entered as a cross-reference to the line of the parts list wherethe items actual part or identifying number and description are given.NOTE: Reference designations
45、for electrical and electronic parts and equipment, in accordance with ASME Y14.44, may be used asfind numbers or item numbers.3.18 Flag Noteflag note: a note whose text is prefixed by a note identification enclosed within a symbol (flag). The note is cross-referenced to a specific area on a drawing
46、or associated list by entering the flag at the point of application.3.19 Identification Cross-Reference Drawingidentification cross-reference drawing: an administrative-type drawing that assigns a compatible identifier(s) to providea cross-reference to the original incompatible identifier(s) (ASME Y
47、14.24).3.20 Index Listindex list: a tabulation of data lists and subordinate index lists pertaining to the item(s) to which the index listapplies. See Figs. 3-5 and 3-6.3.21 Itemitem: a nonspecific term used to denote any unit or product, including materials, parts, assemblies, equipment,accessories
48、, and computer software (ASME Y14.100).4ASME Y14.34-20133.22 Parts Listparts list: a tabulation of all parts and bulk materials used in the item(s), except those materials that support aprocess and are not retained, such as cleaning solvents and masking materials.3.22.1 Integral Parts Listintegral p
49、arts list: a parts list prepared and revised as part of an engineering drawing.3.22.2 Separate Parts Listseparate parts list: a parts list prepared as a document separate from the engineering drawing to which it isassociated, and one that may be revised independently of the drawing. See Figs. 3-7 and 3-8.NOTE: Other terms previously used to describe a parts list are list of materials, bill of materials, stock list, and item list.3.23 Product Data Management (PDM) Systemproduct data management (PDM) system: an automated database s
