1、Ms52000A14 DeCamber 19S2F=lA-A-52481October 28, 1993SUPERSEDINGMMERCIFJ. ITEM DESCRIPTIONGABRET, RUBBER, SYNTHSTICThe General Services Administration hae authorized the use of thiscommercial item description (CID) as a replacement for Ms52000A, which iscanceled.ABSTRACTThis CIO covers a synthetic, r
2、ubber gasket used between electric receptacleconnectors. Gasket is intended to be used for wall and box mounting.SALIENT CRARACTERISTICSa. Deeign and construction. The design and construction of the gasket shallbe in accordance with figure 1.b. Materials. Gaskets shall be made of materials conformin
3、g to rubberM2SCS15 Grade SCS15C1E3 per ASTM D2000. The use of recovered materials rrmde incompliance with regulatory reguirenmnte is acceptable providing that allreguiraments of this CID are met (see note e).c. Identification nmrkings. Identification markings shall be permanent andlegible and ehall
4、include, as a minimum, the manufacturers identification code(CAGE) and part number, militsry part identification number (PIN), and the dateof manufacture/cure date (see note b).QUALITY ASSUAANCB PROVISIONSa. Respa risibility for inspection. The contractor is responsible for theP8rformsnce of all ins
5、pections (examinations and tests).Beneficial com!nenta, recommendation, additions, deletions clarifications, etc.and any other data which may improve this document should be sent by letter to:U.S. -y Tank-Automotive Command, ATTN: AMSTA-GDS, Warren, HI 48397-5000.AMSC N/A Fsc 5330DISTRIBUTION STATEM
6、BNT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52481rBT:F1PIN D?.mh DInNo. A52401 A-1 I .437-2 I .500-3 I .5,7DIHB DIM+.016 c-.000+=.875 .2971.000 .3591.094 .406DIADIM E Rm D1A DIMD +
7、.016 F G H-.000 +.010.594 .500 .141 .i72 .031-4 .594 1.188 .453 .906 .015 .141 .172 .031-5 .641 1.281 .483 .969 1.000 .156 .112 .031-6 .688 1.375 .531 1.063 1.125 .156 .203 .031-7 .750 1.500 .518 1.156 1.250 .172 .203 .031-8 .813 1.625 .625 1.250 1.375 .188 .203 .031-9 .075 1.750 .687 1.375 1.500 .1
8、88 .203 .031-10 1.000 2.000 .781 1.563 1.7S0 .219 .203 .031-11 1.344 2.688 1.094 2.188 1.750 .2s0 .203 .031-12 1.125 2.250 .075 1.750 2.000 .250 .219 .0211 t! 1 ! I 1 1-13 1.250 2.500 .969 1.938 2.188 .281 .219 .031-14 1.375 2.750 1.094 2.188 2.437 .281 .219 .031UIE: Dimensionsare in i.thee. unless
9、C.tberwime a75gecified, toleranceare : .010 on decimals. IFIGUAE 1. Gaeket, rubber, synthetic.2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52481b. Contractor certification. The contractor shall certify and maintainsubstantiating evidence that
10、 the Product offered meets the salientcharacteristic of this commercial item description and that the product conformsto the producers own drawings, specifications, workmanship standards, andguality assurance practicee. Items with known defects shall not be submitted forGOVernMOtIt acceptance. The G
11、overnment reserves the right to require prOOf ofeuch conformance prior to the first delivery and thereafter as may be otherwiseprovided for under the provisions of the contract.PRESERVATION, PACRAGING, PACXING, LASELING, AND WINGPreservation, packaging, packing, labeling, and marking for the desired
12、 levelshall be as specified in the contract (see note b).NOTSS(This section containe information of a general or explanatory nature thatmay be helpful, but is not mandatory. )a. Addresses for obtaining copies of referenced documents.1. Non-Government epecificatione and standards. A.52nD2000 “Standar
13、dClassification System for Rubber Producte in Automotive Applications” isavailable from the American Society for Testing and Mater iale, 1916 RaCe Street,Philadelphia, PA 19103.b. Ordering data. Acquisition documente must specify the following:1. Title, number, and date of this CID.2. Gasket eize an
14、d PIN number (see figure 1).3. Selection of applicable level and packaging requirements.4. If marking is other than specified.c. Croaa-reference data. Gaskets conforming to this CID areinterchangee/substitutable with gaskets conforming to 14S52000(AT), dated14 December, 1982.1. Former part numbers.
15、PIN dash numbers are the same as MS52000(AT)dash numbers which are cross referenced ae follows:Former shell sizeDash Ordnance (MS31OONumber Part Number distribution is unlimited.I 10f2IProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-11589/175
16、FWLOR PATTBRW SIZE : Miniature FINISH : MoireTOTAL WIDTH OF STRIPES FWNCTION OF COLOR & CABLE NUWBERWID7!S INCwFs & METRIC STRIPES STRIPES FILLING YARN1/32 (0.8 Uul) Edge & Binder White 5A 671011/32 (0.8 mm) Ground Black SAW 671381/32 (0.8 nun) Ground Paprica SSA 671511/32 (0.8 mm) Ground Black WAN
17、671381/32 (0.8 mm) Ground White EA 671013/32 (2.4 mm) Ground Paprica HBA 671s11/32 (0. s Unn) Ground White SA 671011/32 (0. s mm) Ground Paprica HBA 6715111/16 1/16 (1.5 mm) Ground Old Glory Blue ECC 67178 White WA 67101(17.5 mm) 1/32 (0. s IIKO) Ground Paprica HBA 671511/32 (0.8 mm) Ground White HA
18、 671013/32 (2.4 mm) Ground Paprica SEA 671511/32 (0.8 m) Ground White HA 671011/32 (0.8 mm) Ground Black HAN 671381/32 (0.8 mm) Ground Paprica 58A 671511/32 (0.8 mm) Ground Black HAN 671381/32 (0.8 mm) Edge & Binder White HA 67101CHANGES FROM PREVIOUS ISSUS : Marginal notations sre not used in this
19、revi.eion toidentify chsngea with respect to the previoue issue due to the extent of the changes.CLmtodisns : Preparing activity:A=UY-IM MMY - IHReview activities: (Project No. 8455-0815)DLA -CTcivil Agency Coordinating Activities:DoT2a71a71Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
