1、MIL-DTL-60585B (AR) W/AMENDMENT 1 0 INCH-POUND MIL-DTL-60585B (AR) W/AMENDMENT 1 20 September 2006 SUPERSEDING MIL-DTL-60585B (AR) 20 June 2006 DETAILED SPECIFICATION CASE, PROJECTILE BURSTER ASSEMBLY, M1E1 This specification is approved for use by the U.S. Army ARDEC, and is available for use by al
2、l Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements, examinations and tests for the metal parts of the Case, Projectile Burster Assembly, M1E1. 2. APPLICABLE DOCUMENTS. 2.1 General. The documents listed in this section are needed to
3、 meet the requirements specified in sections 3 and 4 of this specification. This section does not include documents in other sections of this specification or recommended for additional information or as examples. While every effort has been made to assure the completeness of this list, document use
4、rs are cautioned that they must meet all requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. AMSC N/A FSC:1320 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Comments, suggestions, or questions on this document sh
5、ould be addressed to the Commander, U.S. Army ARDEC, ATTN: AMSRD-AAR-AIS-SS, Picatinny, NJ 07806-5000 or emailed to ardec-stdznpica.army.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dl
6、a.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60585B (AR) W/AMENDMENT 1 2 2.2 Government documents. 2.2.1 Specification, standards and handbooks. The following specifications, standards, and handbooks form a part of this specificatio
7、n to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1916 - DOD Preferred Method of Acceptance of Product (Copies of these documents are available online at http:/assist.da
8、ps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Documents Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings and publications. The following other Government documents, drawings and publications below
9、 form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. U.S. ARMY ARMAMENT RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER (ARDEC) DRAWINGS 10542950 - Case, Projectile, Burster, M1E1 Assembly 10542949 - Case, Burster 105
10、35949 - Tube Reinforcing 9217031 - Projectile, 155MM: Smoke, WP, M110A2, Filling Assembly (Copies of these drawings may be requested online at Drawing-Requestpica.army.mil or from US Army ARDEC, ATTN: AMSRD-AAR-AIS-T, Picatinny, NJ 07806-5000.) 2.3 Non-Government publications. The following document
11、s form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents are those cited in the solicitation or contract. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60585B (AR) W/AMENDMENT 1
12、3 ASTM INTERNATIONAL ASTM E 8 - Standard Test Method for Tension Testing of Metallic Materials ASTM E 18 - Standard Test Method for Rockwell Hardness and Rockwell Superficial Hardness of Metallic Materials (Copies of ASTM standards are available online from http:/www.astm.org/ and from American Soci
13、ety for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) 2.4 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification takes precedence. Nothing in this document, however, sup
14、ersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2) a sample shall be subject to first article inspection in accordance with 4.2. 3.2 Materials, components and assemblies. 3.2.1 Tube reinforcing. The mater
15、ials, components and assemblies shall comply with all requirements specified on Drawing 10535949. 3.2.2 Sleeve (alternative two piece design). The materials, components and assemblies shall comply with all requirements specified on Drawing 10542949. 3.2.3 Casing (alternative two piece design). The m
16、aterials, components and assemblies shall comply with all requirements specified on Drawing 10542949. 3.2.4 Plug and casing (alternative design). The materials, components and assemblies shall comply with all requirements specified on Drawing 10542949 and paragraph 4.3.3.1. 3.2.5 Burster case. The m
17、aterials, components and assemblies shall comply with all requirements specified on Drawing 10542949. 3.2.6 Case, projectile, burster assembly (prior to coating). The materials, components and assemblies shall comply with all requirements specified on Drawing 10542950. 3.2.7 Case, projectile, burste
18、r assembly. The materials, components and assemblies shall comply with all requirements specified on Drawing 10542950. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60585B (AR) W/AMENDMENT 1 4 3.2.8 Ammunition lot numbering. Ammunition lot
19、numbering shall be assigned in accordance with drawing 10542950. 3.3 Brazed joint (alternative designs). The braze metal shall be visible for the full 360 degrees around the joint at the juncture of casing and rear of sleeve and also the juncture of the casing and base plug, outside, if applicable.
20、3.3.1 Joint sections (alternative designs). When sectionalized, the braze metal joint shall be free of voids, cracks, entrapped slag, cleaning or other fluid for an aggregate of 85 percent of the exposed joint section. 3.4 Protective coating. The components and assemblies shall comply with all requi
21、rements specified on Drawing 10542950. 3.4.1 Cleaning prior to protective coating. Prior to application of the protective coating all surfaces of the burster case shall be thoroughly cleaned to remove all traces of grit, oil, wax, grease, rust or other foreign matter. 3.4.2 Cleaning prior to testing
22、. The burster casing, prior to hydrostatic and air testing, shall be free from rust and other foreign matter in order no to clog passages and possibly result in false non-leakers. 3.5 Metal defects. The burster case and burster case assembly shall be free from cracks, splits, cold shuts, inclusions,
23、 porosity, laps, seams or other similar defects. 3.6 Burr. The burster case and burster case assembly shall contain no burr which might interfere with assembly or function of the item or which might be injurious to personnel handling the item. 3.7 Workmanship. All parts and assemblies shall be lubri
24、cated, loaded and assembled in a thorough, skillful manner. Components shall be free of burrs, sharp edges, cracks, dirt, grease, corrosion, and other foreign matter. Cleaning methods shall not be injurious to any parts, nor shall the cleaning agents contaminate the parts. All required marking and s
25、tamping shall be neat and sharply defined. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60585B (AR) W/AMENDMENT 1 5 4. VERIFICATION Table I Requirement/verification cross-reference METHOD OF VERIFICATION CLASSES OF VERIFICATION N/A NOT APP
26、LICABLE 1 ANALYSIS A FIRST ARTICLE 2 DEMONSTRATION 3 EXAMINATION B ACCEPTANCE 4 TEST VERIFICATION METHOD VERIFICATION CLASS SECTION 3 REQUIREMENTS DESCRIPTION N/A 1 2 3 4 A B SECTION 4 VERIFICATION 3.1 First article XXX 4.2 4.2.1 3.2 Components and assemblies XXX X 4.3.2.1 4.3.2.7 3.2.1 Tube reinfor
27、cing X X X X 4.3.2.1 3.2.2 Sleeve (alternative two piece design) X X X X 4.3.2.2 3.2.3 Casing (alternative two piece design) X X X X 4.3.2.3 3.2.4 Plug and casing X X X X 4.3.2.4 4.3.3.1 3.2.5 Burster case X X X X 4.3.2.5 3.2.6 Case, projectile, burster assembly (prior to coating) X X X X 4.3.2.6 3.
28、2.7 Case, projectile, burster assembly X X X X 4.3.2.7 3.2.8 Ammunition lot numbering X X X 4.3.2.6 3.3 Brazed joint X X X 4.3.3.3 3.3.1 Joint sections (alternative design) X X X 4.3.3.3 3.4 Protective coating X X X 4.3.2.7 3.4.1 Cleaning prior to protective coating X X X 4.3.2.6 3.4.2 Cleaning prio
29、r to testing X X X 4.3.2.6 3.5 Metal defects X X X 4.3.2.1 - 4.3.2.6 3.6 Burr X X X 4.3.2.1 4.3.2.63.7 Workmanship X X X 4.3.2.1 - 4.3.2.6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60585B (AR) W/AMENDMENT 1 6 4.1 Classification of verif
30、ication. a. First article inspection (see 4.3). b. Conformance inspection (see 4.3). 4.2 First article verification. When specified, a sample of the cartridge and its components shall be subjected to First Article Verification in accordance with Table II. 4.2.1 First article quantity. First article
31、verification shall be performed on the quantity of item indicated. Part description Drawing Quantity Tube, reinforcing 10535949 10 Sleeve 10542949 10* Casing 10542949 10* Plug 10542949 10* Case, Projectile, 10542950 10 Burster Assembly (prior to coating) Case, Projectile, 10542950 10 Burster Assembl
32、y * These items shall be submitted if alternative design is used. 4.2.2 Rejection. If any item fails to comply with requirements, the first article sample shall be rejected. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60585B (AR) W/AMENDM
33、ENT 1 7 TABLE II - First article inspection PART NUMBEER OF SAMPLES REQUIREMENT PARAGRAPH INSPECTION METHOD REFERENCE Tube, reinforcing Dwg. 10535949 10 3.2.1 4.3.2.1 Sleeve Dwg. 10542949 Note 1 10 3.2.2 4.3.2.2 Casing Dwg. 10542949 Note 1 10 3.2.3 4.3.2.3 Plug Dwg. 10542949 Note 1 10 3.2.4 4.3.2.4
34、Case, Projectile, Dwg. 10542950 10 3.2.6 4.3.2.6 Burster Assembly (prior to coating) Case, Projectile, Dwg. 10542950 10 3.2.7 4.3.2.7 Burster Assembly Note 1. These items shall be submitted if alternate design is used. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
35、nse from IHS-,-,-MIL-DTL-60585B (AR) W/AMENDMENT 1 8 4.3 Conformance inspection. 4.3.1 Lot formation. Lot formation shall be in accordance with lot formation requirement of MIL-STD-1916 paragraph “Formation and identification of lots or batches”. In addition, each lot of projectile burster cases sha
36、ll contain: a. Tubing lots containing not more than one heat of steel. b. Bar stock lots containing not more than one heat of steel. 4.3.2 Conformance inspection by classification of characteristics. See paragraphs 4.3.2.1 through 4.3.2.7. Provided by IHSNot for ResaleNo reproduction or networking p
37、ermitted without license from IHS-,-,-MIL-DTL-60585B (AR) W/AMENDMENT 1 9 Conformance inspection by classification of characteristic DRAWING NUMBER 10535949 PARAGRAPH 4.3.2.1 TITLE Tube, reinforcing SHEET 1 OF 1 NEXT HIGHER ASSEMBLY 10542950 CLASSIFICATION EXAMINATION OR TEST CONFORMANCE CRITERIA RE
38、QUIREMENT PARAGRAPH INSPECTION METHOD REFERENCE Critical None defined Major 101 Inside diameter Level IV 3.2.1 AIE 102 Thickness of wall Level IV 3.2.1 AIE * 103 Metal defective Level IV 3.2.1/3.5 Visual Minor 201 Minimum flat of wall front and rear Level II 3.2.1 AIE 202 Length total Level II 3.2.1
39、 AIE 203 Width of slot Level II 3.2.1 AIE 204 Radii or chamfers missing or incorrect Level II 3.2.1 Visual 205 Surface finish, improper Level II 3.2.1 Visual 206 Burr Level II 3.6 Visual 207 Foreign matter Level II 3.7 Visual Provided by IHSNot for ResaleNo reproduction or networking permitted witho
40、ut license from IHS-,-,-MIL-DTL-60585B (AR) W/AMENDMENT 1 10 Conformance inspection by classification of characteristic DRAWING NUMBER 10542949 PARAGRAPH 4.3.2.2 TITLE Sleeve (Alternative Two Piece Design) SHEET 1 OF 1 NEXT HIGHER ASSEMBLY 10542950 CLASSIFICATION EXAMINATION OR TEST CONFORMANCE CRIT
41、ERIA REQUIREMENT PARAGRAPH INSPECTION METHOD REFERENCE Critical None defined Major 101 Diameter of counterbore rear of sleeve Level IV 3.2.2 AIE 102 Diameter at rear of sleeve (outside) Level IV 3.2.2 AIE 103 104 Length total Diameter of through hole max Level IV Level IV 3.2.2 3.2.2 AIE AIE Minor 2
42、01 Length from rear of flange to bottom Level II 3.2.2 AIE of counterbore rear of sleeve 202 Radii or chamfers missing or incorrect Level II 3.2.2 Visual 203 Surface finish improper Level II 3.2.2 Visual 204 Burr Level II 3.6 Visual 205 206 Foreign matter Evidence of poor workmanship Level II Level
43、II 3.7 3.7 Visual Visual * 207 Metal defective Level II 3.2.2/3.5 Visual Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60585B (AR) W/AMENDMENT 1 11 Conformance inspection by classification of characteristic DRAWING NUMBER 10542949 PARAGRAPH
44、 4.3.2.3 TITLE Casing (Alternative Two Piece Design) SHEET 1 OF 1 NEXT HIGHER ASSEMBLY 10542950 CLASSIFICATION EXAMINATION OR TEST CONFORMANCE CRITERIA REQUIREMENT PARAGRAPH INSPECTION METHOD REFERENCE Critical None defined Major 101 Diameter at front of tube (outside) Level IV 3.2.3 AIE for minimum
45、 indicated length 102 Outside diameter at rear of transition zone Level IV 3.2.3 AIE 103 Thickness of wall minimum for minimum Level IV 3.2.3 AIE Length 104 Thickness of wall rear of transition Level IV 3.2.3 AIE Zone Minor 201 Radii or chamfers missing or incorrect Level II 3.2.3 Visual 202 Surface
46、 finish improper Level II 3.2.3 Visual 203 Burr Level II 3.6 Visual 204 Foreign matter Level II 3.7 Visual 205 Evidence of poor workmanship Level II 3.7 Visual * 206 Metal defective Level II 3.2.3/3.5 Visual Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH
47、S-,-,-MIL-DTL-60585B (AR) W/AMENDMENT 1 12 Conformance inspection by classification of characteristic DRAWING NUMBER 10542949 PARAGRAPH 4.3.2.4 TITLE Plug and Casing (Alternative Design) SHEET 1 OF 1 NEXT HIGHER ASSEMBLY 10542950 CLASSIFICATION EXAMINATION OR TEST CONFORMANCE CRITERIA REQUIREMENT PARAGRAPH INSPECTION METHOD REFERENCE Critical None defined Major 101 Large Diameter Level IV 3.2.4 AIE 102 Length of small diameter Level IV 3.2.4 AIE 103 104 105 106 * 107 Radius on plug corner Small diameter Diameter of counterbore at rear of casing Depth of counterbore at rear casing Thicknes
