1、.- 5-37-03 MIL-1-52997 (2) 10 M 9999906 0339Y25 B M _- . MIL-I-52997blE) AMENDMENT 2 3 June 1985 SUPERSEDING AMENDMENT 1 6 July 1983 MILITARY SPECIFICATION INSTALLATION FIXTURE KIT, ROLLER, MINE CLEARING : TRACK-W IDTH, TANK-MOUNTED This amendment forms a part of Military Specification MIL-I-52997(M
2、E), dated 16 February 1982, and is approved for use by the USA Belvoir Research and Development Center, Department of the Army and is available for use by all Departments and Agencies of the Department of Defense. PAGE 2 * 2.1.1, under STANDARDS, FEDERAL, delete: “FED-STD-101 Under STANDARDS, MILITA
3、RY, delete: %IIL-STD-l188 - Preservation, Packaging, and Packing Materials, Test Procedures - Commercial Packaging of Supplies and Equipment. II * 2.2, add at bottom of page: “AMERICAN SOCIETY FOR TESTING AND MATERIALS AST) ASTM D 3951 - Standard Practice for Cornniercial Packaging. (Application for
4、 copies should be addressed to the American Society for Testing and Materials, 1916 Race St, Philadelphia, PA 19103).“ PAGE 4 3.8.2, line 8, after %sed.“, add sentences “Weld -shall not exceed the next For welds 3/8 inch and larger, 1/16 in larger size for welds up to 318 inch. the size shall not ex
5、ceed the next 118 inch larger size. undersize.“ Welds shall not be PAGE S * 4.7.1, delete and substitute “4.7.1 First article inspection of packaging.“ FSC 1095 Page 1 of 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - U flIL-I-s2777 (2) LO 9779
6、706 0331426 T W - MIL-1-5299 7 (ME) AMENDMENT 2 * 4.7.1.1, delete and substitute “4.7.1.1 Examination. First article packaging shall be examined for the defects specified in table III. more defects shall be cause for rejection.“ 1 Presence of one or PAGE 9 * 5.1, delete the heading “Preproduction pa
7、ck.“ and substitute “First article packaging. I * 5.1, lines 1, 6, 7, 8, 10, delete “preproduction“ and substitute “first article“. * 5.1, line 2, delete “and testing“ without substitution. * Line 5, delete “and tests“ without substitution and delete “those“ and substitute “as“. * 5.3, delete the pe
8、riod after “as specifiedr1 and add “(see 6.2).“ PAGE 10 * 5.3.2, delete and substitute: “5.3.2 Commercial. A complete kit shall be packed according to ASTM D 3951.“ * 5.4.2, delete and substitute: 1 “5.4.2 Commercial Marking for commercial packaging shall be in accordance with ASIM D 3951. the gross
9、 weight and cube.“ Additionally, each shipping container shall be marked with * Add the following new paragraph: “6.5 First article pack. Any changes or deviations of production packs from the approved first article pack during production will be subject to the _- approval of the contracting officer
10、. not relieve the contractor of his obligation to preserve, pack, and mark the kits in accordance with the specification.“ The margins of this amendment are marked with an asterisk to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were made. Thi
11、s was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Approval of the first article pack will Page 2 of 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- r MIL-1-52997 (2) LO 999
12、7906 0334427 L MIL-1-5299 7 (ME AMENDMENT 2 I Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. Custodian: Army -ME Review activity: Army - AT 3 Preparing activity: Army - ME Project 1095-Al75 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
