1、e: 19 June 1981 SUPERSEDING MIL-L-43582A 5 April 1978 MILITAKY. SPECIFICATION LINER, SHIRT , CIIEMICAL PROTECTIVE This specification is appraved for use by all Departments and Agencies of the Depar tment of Defense. 1. SCOPE 1.1 Scope. liner This specification covers the requirements or a cotton sat
2、een shirt 1.2 Classification. The liner shall be of one type in the following sizes (see 6.2). . Schedule of sizes X-small Srnail Medium Large X-large 2 0 APPJAICABLE DOCUMENTS * 2.1 The following documents, of the issue in effect on date of invitation for bids or request for proposal, form a part o
3、f this specification to the extent specified herein: Issues of documents. BeneEicial comments (recommendations, additions, deletions) an any . pertinent data which may be of use in improving this document should be addressed to: Natick, MA Iinprovement Proposal (DD Form 1426) appearing at the end of
4、 this document. or by letter. US Army Natick Research arid Development Laboratories, 01760 by using the self-addressed Standardization Document . . . FSC 8415 , . , . , . . . . A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-L-435828 8L( 77777
5、06 0374980 b m MIL-L-43582 B SPECIFICATIONS V-B-871 - Button, Sewing Hole, and Button Staple (Plastic) V-T-276 - Thread, Cotton V-T-250 - Thread, Gimp, Cotton, Buttonhole UU-P-268 - Paper, Kraft, Wrapping DDD-L-2 O - Label: for Clothing, Equipage, and Tentage PPP-B-636 - Boxes, Shipping, Fiberboard
6、(General Use) MILITARY MIL-C-10296 - Cloth, Sateen, Cotton STANDARDS FEDERAL FED-STD-191 - Textile Test Methods FED-STD-751 - Stitches, Seams, and Stitchings .MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage MIL-STD-118
7、8 - Commercial Packaging of Supplies and Equi,pment (Copies of specifications, standards, drawings, and publications required by contractors in accordance with specific procurement fiinctions should be obtained rom the procuring activity or as directed by the contracting officer.) 3.1 Samples. 3.1.1
8、 Guide sample. Samples, when furnished, are solely for guidance and information ,to the contractor (see 6.3). ,Variations from the specification may appear in the sample, in which case this specification shall govern. 3.2 Naterials (see 6.5). 3.2.1 Basic material. to class 1 of MIL-C-10296, with the
9、 additional requirement that it show a minimum dynamic absorption of 60 percent when tested as specified in 4.3.1. The material shall be,dyed Olive Green 107. The basic material shall be cotton sateen cloth conforming 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without lic
10、ense from IHS-,-,-MIL-L-4 3582B 3.2.2 Cuff tubing, The fabric for the cuff shall be a seamless, true one by one rib knit, dyed cotton tuhing conforming to the following requirements when tested as specified in 4.3.1. Yards per pound - minimum 9, maximum 12 Wales per inch, minimum - 16 Courses per in
11、ch, minimum - 20 Flat width, inches, minimum - 3 3.2.2-1 ia -alii o al m MU U 0 alau Fi Mal4 asa U ou al am Fi O Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-435828 84 9 7797906 0394979 IY W O U 3 u ma zw y.m,o u mo II -w -I a w w z MIL-L-4
12、3582B m 0 0 m I O 1 I I O O O m m ln m ., m m m mm II O6 I O m m m mm I O I O . . rl N m $4 rl 4 - I Iw rl O m % (d u k cd ai rl a (d m-4 u am d k Mu o ala 3 NEO dd udua o 6s cwou ou a WE Pal o rlao al we m (d a a t( u d m O a a (d d w 8 s d ci Ud abl a W ln 3 W. m f O Yh Provided by IHSNot for Resa
13、leNo reproduction or networking permitted without license from IHS-,-,-. NIL-L-Y35ZB 84 7997706 0394771 O MIL-L-43582B 2 w z W E 3 U W li! ln -z. O t- 4 CY W Q O - 111. l a 2 a (d al $4 C U al v1 O O rl g 8 o d P 2 4 td U v) a 2 v1 U O a m e 0 13 Provided by IHSNot for ResaleNo reproduction or netwo
14、rking permitted without license from IHS-,-,- _ MIL-L-435828 84 7779906 0374972 2 U MIL-L-443582B 3.7 Finished measurements. The finished measurements shall conform to table 11. TABLE II. Finished measurements (in inches) Sizes 112 Breast 1 Back length - 21 Sleeve length a1 X- small Small 2 0-3 14 2
15、2-314 3 1-5 /8 32-118 21-314 21-314 Medium 2 4-3 14 32-518 21-314 La.rge 26-3 14 33-118 2 1-3 14 X-large Tole rances 28-314 i- 314 I 33-518 +1 - 21-314 4- 112 - - 11 112 breast - taken with liner buttoned, from folded edge.to folded edge at base of armhole. 21 Back length - taken at cmter back from
16、bottom edge of collar to bottom edge of liner . - 31 Sleeve length - taken from base of armhole to bottom edge of cuff. 3.8 Workmanship. The finished liner shall conform to the quality of product established by this specification. The occurance of defects shall not exceed the applicable acceptable q
17、uality levels. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract, thecqntractor is responsible for the performance of all inspection requirments as specified herein. Except as otherwise specified in the contract, the contractor may use hi8
18、own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure sup
19、plies and services conform to prescribed requirements. 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-4352B 4 777770b 0374973 4 - MIL-L-43582B . 4-3 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall b
20、e performed in accordance with MIL-STD-105. 4.3.1 Component and material inspection. In accordance with 4.1, components and materials shall be inspected in accordance with all the requirements of referenced specifications, drawings, and standards, unless otherwise excluded, amended, modified, or qua
21、lified in this specification or applicable purchase document. addition to testing provisions contained in component specifications, testing shall be performed on components listed in table III for characteristics noted. methods of testing specified in FED-STD-191, wherever applicable, and as listed
22、in table III shall be followed. Unless otherwise specified in subsidiary specifications, sampling shall be in accordance with the following: In The All requirements are applicable to the sample unit. Lot size Sample size 800 or less 2 801 to 22,000 inclusive 3 22,001 and over 5 The lot shall be unac
23、ceptable if one or more sample units fail to meet any test requirement specified. utilized in expressing the final result. sample unit for testing each component shall be in accordance with applicable subsidiary specifications and as follows: All test reports shall contain the individual values The
24、unit for expressing lot size, and the Component Lot size expressed as Sample unit for testing Cot ton knit Yards 1-112 yards full width tubing Cotton sateen Yards 1/2 yard full width cloth TABLE III. Test methods Requirement Test Component Characteristic paragraph methsd Cot ton sateen Dynamic absor
25、ption cloth 3.2.1 Cotton knit tubing Material identification 3.2.2 Type of knit 3 02 -2 Yards per pound 392.2 Wales per inch 3 -2.2 5500 1200 Visual i/ 5041 5070 - 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL- - 358 _- _ - - MIL-L-4358ZB 19
26、9 77777Ob 0394774 b B TABLE III. Test methods (contd) - Requirement Test Component Characteristic paragraph method Cot ton knit Courses per inch 3.2.2 tubing (contd) Width (flat) 3.2.2 PB 3 -2 -2 -1 Color 3.2.2.2 Presence of labile sulfur 3 e2 -2 -2 Colorfastness to: 3.2.2.4 - laundering - perspirat
27、ion - crocking 5070 5020 2811 Visual i/ 2020 - 5610 5680 5651 Nonf ibrous material 3.2-2.5 261 1 Starch and protein content (including chloroform- soluble and water-soluble material) I i/ One determination shall be made on each sample unit and the results reported as “pass“ or “fail“, 4.3.2 End item
28、 examination. The end item shall be examined in accordance with The 4.3.2.1 and 4.3.2.2. sample unit ahall be one liner. The lot size shall be expressed in units of one liner. 4.3.2.1 Visual examination. The end item shall be examinad for the defects listed below. (AQL) shall be 2.5 major, 15.0 majo
29、r and minor A combined, and 40.0 total (major, minor A, and minor R combined) defects per hundred units. The inspection level shall be II and the acceptable qualip.leve1 fiaterial defects and damages a. Applicable to cotton sateen: 1. Any hole, needle chew, cut, tear, mend, or burn 2. Any defect suc
30、h as a smash, multiple float, or loose s lub 16 x. X Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-43582B 4 9779906 O374795 8 m- MIL-L-4 3582B Classification Major Minor Defect AB Material defects and damages (cont d) b, Applicable to knitted
31、 cuffs: . L. Hole, run, or dropped stitches 2. Elasticity lacking, i.e, tight or stretched 3. Slubby yarn 4. Mend NOTE: Material defects add damages are to be classified as indicated above only when the condition is one which weakens the cloth or liner or when it is so conspicuously located as to be
32、 clearly noticeable. conditions which are inconspicuous shall not be classified Non-weakening as defects. Cleanness a. b. C. Components and assembly a. b. Any spot or stain on outside Thread ends not trimmed to a maximum length of 1/4 inch One or more size markings not removed, when applicable or lo
33、ose threads not removed rom major portion of liner Any component part or required operatlon omitted (unless Any operation not performed as specified (unless otherwise otherwise classified herein) classified herein) Cut t in Stitches not caught in cloth, causing stitching to C. d. e. Gimp omitted: pu
34、ll away froin cloth Not specified type, or uncut buttonhole Ragged edges - one or more broken or skipped stitches in one or more buttonholes - in one buttonhole - in two or more buttonholes 19 X X X X X X X X X X X X X X X X X Provided by IHSNot for ResaleNo reproduction or networking permitted with
35、out license from IHS-,-,-MIL-L-435ZB 4 7777706 0374798 3 = MIL-L-4 3582 B Classification Major Minor Defect AB Buttonholes (construction) (contd) f. Purling on the inside of liner g. Ends not tacked in: - one buttonhole - two or more buttonholes h. Cut length less than 3/4 or more than 718 inch S le
36、 eves a. b. Cuff badly twisted c. Cuff spliced - not tubular construction d. Cuff not constructed of double thickness Cuff finished less than 5-314 or more than 6-114 inches long But tons Missing, loose or defective: - one button - - two or more buttons Bot torn hem a. Formed on inside of liner b. S
37、titching across end of he.- r i ur Width leis than 1/2 or more than 3/4 inch wide C. mitted Shoulder, armhole, und.erarm and side and sleeve seam a. b. C. Front lapped on back at shoulder seam Back lapped on front at side seam and underarm Sleeve lapped on front or back at armhole seam Fr o nt facin
38、gs a. Stitched on inside of liner b. Back edge not turned under in stitching, when not cut on C. Tight, short: or twisted, causing excessive fullness or selvage twist on front 20 X X X X X X X X X X X X X X X X X X X Provided by IHSNot for ResaleNo reproduction or networking permitted without licens
39、e from IHS-,-,-MIL-L-43582B 4 - 7999706 O374799 5 MIL-L-43582B Classification e Major Minor Front buttonholes (position) a. b. C. Constructed in vertical position d. Eyelet end toward side seam Unequally spaced by more than 1/2 inch Less than 5/8 or more than 7/8 inch from front edge X X X X Protect
40、ive flap a. One or more buttons out of alignment with front buttonholes by more than 1/4 inch X b. Bartack at top edge missing or insecure X C. Bartack misplaced X d. Bartack less than 3/8 or more than 1/2 inch long X Labels a. b. Identification label missing, incorrect, or illegible C. d. Size labe
41、l, instruction label, or combination label missing, incorrect, or illegible Not positioned as specified or not stitched on all four Positioned off center of back by more than 1/2 inch sides e X X X X 4.3.2.2 Finished measurements (see 3.7). Any measurement deviating from nominal dimension and tolera
42、nce in table of measurement or sleeves uneven in length by 3/4 inch or more shall be scored. The inspection level shall be S-3 and the AQL shall be 4.0 defects per hundred units. 4.3.2.3 Acceptable quality levels and inspection labels. The acceptable quality levels (AQLs) expressed in defects per hu
43、ndred units (DHU) and inspection levels shall be as follows: AQL s For 4.3.2.1: Niajor 2.5 Two Major and Minor A Major. and Hinor A 15 .O and Minor B (combined) 40.0 For 4.3.2.2: One class s-3 4 .O 21 inspection level II Provided by IHSNot for ResaleNo reproduction or networking permitted without li
44、cense from IHS-,-,- -.-_ flIL-L-43582B 84 7779706 0375000 b M .- MIL-L-43582B 4.4 Packaging inspection. An examination shall be made to determine that the preservation, packing, and marking comply with the section 5 requirements. Defects shall be scored in accordance with the list below, The sample
45、unit shall be one shipping container fully packaged with the exception that it need not be closed. Defects of closure listed below shall be examined on shipping containers fully packaged. inspection lot. per hundred units The lot size shall be the number of shipping containers in the end item The in
46、spection level shall be -2 and the AQL.shaI-1 be 2.5 defects Examine Defect Marking Omitted; incorrect; illegible; of improper size, location, (exterior and sequence, or method of application interior) Materials Any component missing, damaged, or not as specified Wo rkmans hip Content Inadequate app
47、lication of components, such as incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling Bulged or distorted container Improperly folded liners, inadequately tied bundles, contc.ts improperly covered with paper Numb f of bundles is more or less than required Nu
48、mber of liners per bundle is more or less than Size shown-on one or more liners not as specified on required i/ container i/ - - l/ For this defect, one bundle frorui each container in the sample shall be examined. 5. PACKAGING * 5.1 Preservation. specified (see 6.2). Preservation-packaging shall be level A or Commercial as 5.1.1 Level A. Each unbuttoned liner shall be laia out flat with the front up. The front width shall be adjusted to approximately 23 inches by over-lapping the left side on tho wight side. the chest. larger sizes it may be necessary to prefold the
