1、t.; I MIL-P-70661 (3) 13 W 9999906 0523546 1 MIL-P-70661 (AR) AMENDMENT 3 10 April 1992 SUPERSEDING AMENDMENT 2 25 MAY 1988 MILITARY SPECIFICATION POTTED CIRCUIT CARD ASSEMBLY FOR TOW-2/E6 PROBE AND SQA ASSEMBLY This Amendment forms a part of Military Specification MIL-P-70661 (AR), dated 27 April 1
2、987 and is approved for use by U.S. Army Armament Munitions and Chemical Command, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 2 STANDARD, MILITARY, delete: iiDOD-STD-2000 - Soldering Technology - High Quality / High Reliabilityi1 and substitute: iiDOD-
3、STD-2000-4 - General Purpose Soldering requirements for electrical and electronic equipmentii PAGE 3 3.5 Second line: delete the sentence Iland an inspection record (per DI-1724) li and substitute Itupon requestii PAGE 4 3.7 Line 3 delete DOD-STD-2000ii and substitute iiDOD-STD-2000-4ii 3.7.1, Line
4、3 : Delete iiDOD-STD-200011 and substitute iiMIL-STD-750ii PAGE 9 * Delete 4.4.2.1. in its entirety and substitute included revised 4.4.2.1 1 of 4 AMSC N/A FSC 1336 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or netwo
5、rking permitted without license from IHS-,-,-k O U (II 4 N V V - MIL-P-70bb1 (3) 13 D 999990b 0523547 3 D o N O N M O O Y O H !2 a (d kk w aal .ri ad U orl k kO al plm u i-1 “fi 124 c) O C 2, E c t Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-t. i
6、 MIL-P-70661 (AR) AMENDMENT 3 PAGE 10 4.4.2.2, Major 103: Delete 1rDOD-STD-2000ii and substitute “MIL-STD-750, Method 2026“ PAGE 11 4.4.2.3, Major 103 : Delete 1tDOD-STD-20001i an substitute !MIL-STD-750, Method 2026“. PAGE 15 4.4.2.7, Add the title I1Maiorii in the category column between 81Critica
7、lii and lilO1ll. 4.4.2.7, Change Major defect 105 in the paragraph reference column from “4 5.1“ to 114.5.1/Approved Electrical Test Equipmentii. PAGE 22 4.4.2.14, Major 103: Delete t1DOD-STD-2000ii and substitute 11MIL-STD-750, Method 2026:. PAGE 23 4.4.2.15, Change Major defect 104 in the paragrap
8、h reference column from Ii4.5.l1l to Ii4.5.1/Approved Electrical Test Equipmentii. * Add: 11 Examination Requirement Inspection Assembly (see note 2) Paragraph Method 3.2 Gage or Test A!& Mal or 108 Contour of 0.40 Examination Requirement Paragraph 3.2 Inspection Method Gage Delete minor 204 in its
9、entirety. PAGE 26 * 6.5 Delete the following paragraph: I 3.5 Quality Inspection Test, DI-R-1724 Demonstration and Evaluation Report 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ MIL-P-70bbL (3) L3 9999906 0523549 7 * MIL-P-70661 (AR) . AMENDME
10、NT 3 The margins of this amendment are marked with an asterisk or vertical lines to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were made. was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies
11、in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. This Custodian : Army-AR Preparing activity Army-AR (Project 1336-A624 ) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
