1、AMSC N/A FSC 5950 MIL-PRF-39010/17 20 September 2013 PERFORMANCE SPECIFICATION SHEET COILS, RADIO FREQUENCY, SHIELDED, MOLDED, FIXED, SURFACE MOUNT ESTABLISHED RELIABILITY test condition B. Both end terminations are to be immersed simultaneously. Rates of immersion, dwell time and withdrawal are hum
2、an controlled. Resistance to solvents: Test is not applicable. Resistance to soldering heat: Method 210 of MIL-STD-202, test condition C. Mounting board to be SMD test substrate per this document. Test to be performed after final electrical in qualification subgroup II; or after final electrical in
3、group B subgroup 3 inspection. Overload: Test coil shall be mounted on SMD test substrate. Low temperature storage: Test coil shall be mounted on SMD test substrate. Vibration: Test coil shall be mounted on SMD test f substrate. Mechanical shock: Test coil shall be mounted on SMD test substrate. Pro
4、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39010/17 3 Life: Test coil shall be mounted on SMD test substrate. Moisture resistance: Method 106 of MIL-STD-202; polarization voltage not required. Step 7a shall be performed during any five of t
5、he first eight cycles only. Step 7b is not applicable. Test coil shall be mounted on SMD test substrate. SMD test substrate: Material shall be a minimum of 95 percent alumina with metallized areas for part mounting. The substrate shall not cause, or contribute to, any failure in any test which it is
6、 used. Coil mounting: Test coils are to be soldered to the SMD test substrate metallized areas using Sn63 solder, or equivalent, by any suitable method that does not exceed a temperature of 265C and a solder time period greater than five seconds. Table II electrical characteristics (final): For any
7、subgroup test requiring coils to be mounted to an SMD test substrate, the electrical characteristics (final) measurements are to be referenced to the electrical characteristic (initial) measurements determined after the test coil is mounted to the test substrate. Part marking: These parts shall be l
8、aser marked. Part or identifying number (PIN): M39010/17-* (dash number from table I) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39010/17 4 Table I Electrical characteristics (initial) and dash numbers Dash Number 1/ Inductance H 2/ Indu
9、ctance Tolerance percent Q minimum 2/ Test frequency (MHz) Self Resonant Frequency min (MHz) 3/ DC resistance (25C) max (ohms) Rated DC current (mA) 4/ AR10* AR11* AR12* AR13* 0.10 0.11 0.12 0.13 5, 10 5 5,10 5 45 45 45 45 25 25 25 25 450 425 425 400 0.025 0.034 0.034 0.037 2,245 1,925 1,925 1,845 A
10、R15* AR16* AR18* AR20* 0.15 0.16 0.18 0.20 5, 10 5 5,10 5 45 45 45 40 25 25 25 25 400 350 350 325 0.037 0.047 0.047 0.067 1,845 1,635 1,635 1,370 AR22* AR24* AR27* AR30* 0.22 0.24 0.27 0.30 5, 10 5 5,10 5 40 40 40 40 25 25 25 25 325 300 300 275 0.067 0.11 0.11 0.13 1,370 1,070 1,070 985 AR33* AR36*
11、AR39* AR43* 0.33 0.36 0.39 0.43 5, 10 5 5,10 5 40 40 40 40 25 25 25 25 275 250 250 235 0.13 0.18 0.18 0.25 985 835 835 710 AR47* AR51* AR56* AR62* 0.47 0.51 0.56 0.62 5, 10 5 5,10 5 40 40 40 40 25 25 25 25 235 210 210 190 0.25 0.33 0.33 0.45 710 615 615 530 AR68* AR75* AR82* 0.68 0.75 0.82 5, 10 5 5
12、10 40 40 40 25 25 25 190 180 180 0.45 0.59 0.59 530 460 460 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39010/17 5 Table I Electrical characteristics (initial) and dash numbers Dash Number 1/ Inductance H 2
13、/ Inductance Tolerance percent Q minimum 2/ Test frequency (MHz) Self Resonant Frequency min (MHz) 3/ DC resistance (25C) max (ohms) Rated DC current (mA) 4/ AR91* A1R0* A1R1* A1R2* 0.91 1.00 1.10 1.20 5 5, 10 5 5, 10 40 40 40 40 25 25 7.9 7.9 119 119 111 111 0.070 0.070 0.10 0.10 1,340 1,340 1,120
14、1,120 A1R3* A1R5* A1R6* A1R8* 1.30 1.50 1.60 1.80 5 5, 10 5 5, 10 40 40 40 40 7.9 7.9 7.9 7.9 98 98 89 89 0.12 0.12 0.14 0.14 1,025 1,025 950 950 A2R0* A2R2* A2R4* A2R7* 2.00 2.20 2.40 2.70 5 5, 10 5 5, 10 40 40 40 40 7.9 7.9 7.9 7.9 85 85 78 78 0.19 0.19 0.28 0.28 815 815 670 670 A3R0* A3R3* A3R6*
15、A3R9* 3.00 3.30 3.60 3.90 5 5, 10 5 5, 10 40 40 40 40 7.9 7.9 7.9 7.9 72 72 64 64 0.35 0.35 0.40 0.40 600 600 560 560 A4R3* A4R7* A5R1* A5R6* 4.30 4.70 5.10 5.60 5 5, 10 5 5, 10 40 40 40 40 7.9 7.9 7.9 7.9 60 60 55 55 0.55 0.55 0.72 0.72 480 480 420 420 A6R2* A6R8* A7R5* A8R2* 6.20 6.80 7.50 8.20 5
16、5, 10 5 5, 10 40 40 40 40 7.9 7.9 7.9 7.9 47 47 43 43 1.02 1.02 1.32 1.32 350 350 310 310 A9R1* A100* A110* A120* 9.10 10.0 11.0 12.0 5 5, 10 5 5, 10 40 40 40 40 7.9 7.9 2.5 2.5 39 39 37 37 1.62 1.62 2.00 2.00 280 280 250 250 1/ The complete dash number will include two additional letters (indicated
17、 by *). The first additional letter will indicate the inductance tolerance (e.g. J = 5%, K = 10%) and the second additional letter will indicate the product level (e.g. C, M, P, R, S) and will be added to the end of the dash number. 2/ Inductance and Q are tested using HP4194A with test fixture 1603
18、4E, or equivalent. 3/ Self resonant frequency tested using HP4291A, HP4194A or equivalent 4/ The rated dc current is based on 90C ambient temperature with a 15C rise. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39010/17 6 Table II Electri
19、cal characteristics (final) Inspection Group Allowable variation from initial measurement Allowable percent from specified minimum value in electrical characteristics (initial) table Inductance (percent) DC resistance Self-resonant frequency Q Qualification inspection Group II Group IV Group VI 5 5
20、5 (3% + 0.001 ohm) (2% +0.001 ohm) 1/ 1/ -10 -10 -10 Group B inspection Subgroup 1 Subgroup 3 Subgroup 4 5 5 5 (2% +0.001 ohm) (3% + 0.001 ohm) 1/ 1/ -10 -10 -10 1/ The self-resonant frequency shall not be less than the value specified in table I Referenced documents: In addition to MIL-PRF-39010, t
21、his document references: MIL-STD-202 MIL-STD-883 Custodians: Preparing activity: Army CR Army - CR Navy EC Air Force 85 Agent: DLA CC DLA - CC Review activities: (Project 5950-2013-038) Army AR, CR4, MI Navy AS, CG, MC, OS, SH Air Force 19, 99 NOTE: The activities listed above were interested in thi
22、s document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
