ARMY MIL-PRF-45085 D-1997 OIL COOLER ASSEMBLY ENGINE AND TRANSMISSION《发动机和变速器的油冷却器组件》.pdf
《ARMY MIL-PRF-45085 D-1997 OIL COOLER ASSEMBLY ENGINE AND TRANSMISSION《发动机和变速器的油冷却器组件》.pdf》由会员分享,可在线阅读,更多相关《ARMY MIL-PRF-45085 D-1997 OIL COOLER ASSEMBLY ENGINE AND TRANSMISSION《发动机和变速器的油冷却器组件》.pdf(22页珍藏版)》请在麦多课文档分享上搜索。
1、 MIL-PRF-45085D 999990b 2030902 T4T W I INCH-POUNDI 4 April 1997 SUPERSEDING 8 September 1987 MIL-PR.F-45 08 5D MIL-C-45085C(AT) PERFORMANCE SPECIFICATION OIL COOLER ASSEMBLY: ENGINE AND TRANSMISSION This specification is approved for use by ail Departments and Agencies of the Department of Defense.
2、 1. SCOPE 1.1 Scope. This specification covers one type of oil cooler assembly for cooling engine and transmission oils (see 6.1) and is comprised of two engineoil cooler core assemblies and one transmission oil cooler assembly. 1.2 Classification. The engine and oil cooler assembly for acquisition
3、purposes comes in three configurations as specified (see 6.2): Configuration A - Oil cooler assembly (Drawing 8690239) Configuration B - Core assembly, engine oil (Drawing 7356770) Configuration C - Core assembly, transmission (torque) oil (Drawing 7356769) Beneficial comments (recommendations, addi
4、tions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U. S. Army Tank-automotive and Armaments Command, ATTN: AMSTA-T-E/BLUE, Wanen, MI 48397-5000, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end
5、 of this document. or bv letter. AMSC NIA FSC 2930 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MHL-PRF-45085D W 9999906 2030903 98b MIL-PRF-45 08 5D 2. APPLICABLE D
6、OCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensu
7、re the completeness of this list, document users are cautioned that they must meet all specified requirement documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specications, standards. and handbooks. The following specifications
8、, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specications and Standards (DoDISS) and supplement thereto, cited in the solicitation
9、(see 6.2). STANDARDS FEDERAL FED-STD-595 - Colors Used in Government Procurement. (Unless otherwise indicated, copies of the above specifications, standards, and handbooks are available fiom the Standardization Document Order Desk, 700 Robbins Avenue, Budding 4D, Philadelphia, PA 191 11-5094.) 2.2.2
10、 Other Government documents, drawings. and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless othenvise specified, the issues are those cited in the solicitation. DRAWINGS ARMY 7356769 7356770 8690239
11、 - Assembly, Torque (Transmission) Oil Cooler Core. - Core Assembly, Engine Oil Cooler. - Oil Cooler Assembly (Commercial). (Copies of these drawings are available from the U.S. Army Tank-automotive and Armaments Command, ATTN: AMSTA-TR-EBLUE, Warren, MI 48397-5000.) 2 Provided by IHSNot for ResaleN
12、o reproduction or networking permitted without license from IHS-,-,-MIL-PRF-45 085D 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in
13、the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN NATIONAL STANDARD INSTITUTE (ANSI) ANSVASQC 21.4 - Sampling Procedures and Tables for Inspecti
14、on by Attributes OD Adopted). (Copies of ANSI documents are available fiom the American National Standard Institute, 11 West 42nd Street, New York, NY 10036.) AMERICAN SOCIETY FOR TESTING AND MATERTALS (ASTM) ASTM B117 - Standard Practice for Operating Salt Spray (Fog) Apparatus OD Adopted). (Copies
15、 of ASTM documents are available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes prece
16、dence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a first article sample shall be subjected to frst article inspection in accordance with 4.2. 3.2 Materials.
17、 Unless otherwise specified herein or specified in the applicable drawings, materials used shall be in accordance with the manufacturers materials specications for oil cooler assemblies. The materials shall be capable of meeting all the operational and environmental requirements specified herein (se
18、e 4.5.1). Recovered materials shall be used to the maximum extent practicable. Materials and special treatments shall be utilized to prevent corrosion and to resist harmfiil effects of dust, water and fungi. Dissimilar metals shall not be used intimate contact without protection fiom galvanic corros
19、ion. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-45085D 9999906 2030905 759 MIL-PRF-45 08 5D 3.3 Desim and construction. The oil cooler assembly and core assemblies shall conform to ail interface and envelope dimensions on Drawings 8690
20、239,7356770,7356769 and listed parts, as applicable (see 4.5.1 and 4.5.2). 3.3.1 Corrosion and flux control. AU core assemblies shall be internally and externally treated to remove aii corrosion and excess flux. This treatment shall be foliowed by a rinsing and neutralizing treatment, and the core p
21、rotected from further contamination during subsequent operations (see 4.5.1 and 4.5.2). 3.3.2 Internai preservative treatment. Following the operation to remove corrosion and other contaminants, the core shall be flushed with grade 1OW preservative oil in a manner which will insure complete internai
22、 coverage. Mer preservative oil has drained, openings shall be sealed (see 4.5.1 and 4.5.2). 3.3.3 Pretreatment, priming and painting. Core assemblies shall be cleaned, pretreated and primed. Paint color shall match 16187 of FED-STD-595 (see 4.5.2). 3.3.4 Interchangeabilitv. All parts of the oil coo
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ARMYMILPRF45085D1997OILCOOLERASSEMBLYENGINEANDTRANSMISSION 发动机 变速器 冷却器 组件 PDF

链接地址:http://www.mydoc123.com/p-447257.html