1、MIL-T-LZZZG 3 m 777770b 0373776 5 I c- g3 4 Y8 MIL-T-I 11 1G i3 September 1988 SUPERSEDING 13 December 1983 MIL-T-111 1F MILITARY SPECIFICATION TENT, COMMAND POST, M-1945, FIRE, WATER, WEATHER AND MILDEN RESISTANT, OLIVE DRAB, COMPLETE This specification is approved for use by all Departments and Ag
2、encies of the n r Department of Defense. 1- SCOPE 1.1 Scope. This document covers one type of wall tent, having the following dimensions: width, 10 feet; length, 20 feet, 7 inches; ridge height, 9 feet; and side wall height, 5 feet, 10-1/2 inches. The tent is equipped with a liner, detachable sidewa
3、ll screens, and a cover. 2. APPLICABLE DOCUMENTS 2.1 Government documents. e - 2.1.1 Specifications, standards, and handbocks. The following specifications, standards, and handbooks form a part of tkiis specification to the extent specified herein. Unless otherwise specified, the issues of these doc
4、uments shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document s
5、hould be addressed to: U.S. Army Natick Research, Development and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8340 DISTRIBUTION STATEMENT A. Approve
6、d for public release; distribution is unlimited. Y E TiiIS DOCUMENT CONTAINS PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-h- - - - _ MIL-T-LLLLG 83 W 777770b 0373777 7 MIL-T-1111G SPECIFICATIONS FEDERAL L-P-378 L-S-125 T-C-571 T-T-871 T-T-9
7、11 V-F- 106 V-T-285 TT-P -5 95 ccc-c-429 CCC-C-467 DDD-L -20 PPP-B-601 PPP -B -63 6 MIL I TAR Y MIL-P-500 MIL - W-5 3 O MIL-H-1608 MIL-R-1670 MIL-L-1709 MIL-S-1734 MIL-C-2399 MIL -R -3 3 90 MIL-C-10859 MIL-G-16491 MIL -L -3 5078 MIL-T-40625 MIL-S-4 3002 MIL-T-4 3566 MIL-C-43627 MIL-W-43638 MIL -W-4
8、4 O 4 9 Plastic Sheet and Strip, Thin Gauge Polyolefin Screening, Nonmetallic, Insect Cords, Cotton; General and Special Purpose, Sash and Venetian Blind Twine, Cotton, Wrapping Twine, Fibrous, Jute Fasteners, Slide, Interlocking Thread, Polyester Preservative Coating, Canvas Cloth, Osnaburg, Cotton
9、 Cloth, Burlap, Jute (or Kenaf) Label: For Clothing, Equipage and Tentage Boxes, Wood, Cleated Plywood Box, Shipping, Fiberboard (General Use) Plates, Tent Peak and Ridge Webbing, Textile, Cotton, General Purpose, Natural or in Colors Hooks, Tent Rope, Tent-Lay Lines, Tent Slips, Tent Line Cement, L
10、iquid, Tent Patching Rings, Dee Cloth, Oxford, Cotton (Permeable) Grommet, Metallic Loads, Unit: Preparation of Semiperishable Subsistance Items; Clothing, Personal Equipment and Equipage; General Specification For Tubing, Bias Sewn (Burlap or Osnaburg) Cloth Shield, Stovepipe, Tent, Nonmetallic Tap
11、e, Textile, Cotton or Polyester, General Purpose, Cloth, Duck, Cotton, Plied Yarns, Fire, Water, Natural or in Colors Weather and Mildew Resistant Treated, Lightdry Finish Webbing, Textile, Woven, for Tent Framing Webbing, Textile and Tape, Textile, Polypropylene, General Purpose, Natural or in Colo
12、rs 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-11 11G STANDARDS FEDERAL FED-STD-751 - Stitches, Seams, and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment an
13、d Storage MIL-STD-147 - Palletized Unit Load MIL-STD-731 - Quality of Wood Members for Containers and Pallets ies of specifications, standards, and handbooks required by contractor connection with specific acquisition functions should be obtained from the contracting activity or as directed by the c
14、ontracting activity.) in 2.1,2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein. Unless otherwise specifiedj the issues shall be those in effect on the date of
15、 the solicitation. Department of the Army Field Manual FM 10-16 General Repair of Tents, Canvas and Webbing (Copies may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. ) DRAMINGS U.S. ARMY NATICK RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER 5
16、-4-269 5 -4 -270 5-4-271 5-4-272 5-4-273 5-4-2711 5-4-275 5-4-276 5-4-277 5-4-278 5 -4 -279 5-4-280 5-4-5 O1 5-4-504 5-4 -3 359 Tent, Command Post, M-1945, FWMR, OD, Complete; Views and Sections Body and Details Rear End and Details Vestibule Side and Roof Window Details Stovepipe Opening and Screen
17、 Ventilator and Opening Blackout Curtain and Lugs Liner Assembly Liner Body and Details Liner Front End and Rear End Tent, Command Post, M-1945, FWWMR, OD, Complete; Liner Erection Instructions Tent Cover Assembly Erection Instructions 3 Provided by IHSNot for ResaleNo reproduction or networking per
18、mitted without license from IHS-,-,-MIL-T-11 11G (Copies of drawings, publications, and other Government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Other publica
19、tions. The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. issues of documents not listed in the DODISS
20、shall be the issues of the nongovernment documents which are current on the date of solicitation. Unless otherwise specified, the AMERICAN SOCIETY FOR TESTING AND MATERIALS D 3951 - Standard Practice for Commercial Packaging (Copies should be obtained from the American Society for Testing and Materi
21、als, 1916 Race Street, Philadelphia, PA 19103.) (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational services. 1 2.3 Order of
22、 precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained.
23、 3. REQIJIREMENTS 3.1 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.3, 6.2, and 6.4). 3.2 Materials and components. Materials and components shall be as specified herein (see 6.5). 3.2.1 Cloth, cotton duck. The cloth s
24、hall conform to MIL-C-43627, Olive Drab 7. 3.2.2 Cloth, cotton oxford. The cloth shall conform to type I, class 2 of MIL-C-10859. 3.2.3 Tape, textile, cotton. The tape shall be dyed Olive Drab 7 and shall conform to type I, class 4, 3/4-inch, 1-inch, 1-1/2, inch and 2-inch widths of MIL-14-43566. co
25、nforming to type I class 4 of MIL-W-44049. For liners only, alternatively the tape shall be polypropylene, 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-LLLLG 83 m 7777906 0372000 L m I MIL-T-11 1 1G 3.2.4 Webbing, textile, cotton. The webb
26、ing shall be dyed Olive Drab shade No. 7 and shall conform to type III, class 4, 5/8-inch width of MIL-W-530. 3.2.5 Webbing, low elongation. The low elongation webbing shall conform to types I and II of MIL-W-43638. 3.2.6 Thread, polyester. 3.2.6.1 Tent, screens and cover. The thread shall conform t
27、o type I, class 1, sub-class B, shade S-1 (Cable No. 66022) of V-T-285. The dyed thread shall show fastness to weathering equal to or better than the standard shade sample (see 6.3). When no standard shade sample is available, the dyed thread shall show good fastness to weathering. c 3.2.6.2 Liner.
28、The thread shall be natural and shall conform to type I or II, class 1 of V-T-285. 3.2.6.3 Sizes, Thread sizes shall be as follows: For all stitching on tent, screens and cover, - Size FF for needle except bartacking and stitching indicated and F bobbin by llZ1l on drawings For bartacking - Size E f
29、or needle and bobbin For stitching on tent, screens and cover - Size FF for needle, indicated by llZ1l on drawings size F for looper For all stitching on liner, except stitching - Size E for needle indicated by YZli on drawings and bobbin For stitching on liner indicated by llZ1l - Size E for needle
30、 and on drawings for looper 3.2.7 Screening, nonmetallic. The screening shall conform to type III, class 1, size 18 by 18, of L-S-125, and the color shall be olive green. 3.2,8 Shield, pipe, space heater. The stovepipe shield shall conform to MIL-S-43002. 3.2,9 Cord, cotton. The braided cord shall c
31、onform to type I, class 3, size 4 of T-C-571. color of the cord after treatment will be acceptable. The shade shall be olive drab in color prior to finishing. The 5 II Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- -_ _I - - MIL-T-LLLLG 3 W 7779706
32、 0372001 3 MIL-T-1111G 3.2.10 Plastic film. The film shall conform to the requirements for 0.0060 inch thick film, type I, class 1, grade A, B or C, finish 1 of L-P-378 except that the film thickness shall be 0.020 - + 0.004 inch. ink adhesion, water vapor permeability, impact resistance, and heat-s
33、eal strength shall not be applicable. The requirements for slip, 3.2.11 Lines, tent. The tent lines shall conform to MIL-L-1709. Types and use shall be as follows: III VI X XVI XI x XXI Foots top Door tie line Doorflap line and jumper line Jumper line Hoisting line Corner line Door eave line and cov
34、er tie line 3.2.12 Rope, tent-lay, The rope for the stiffener shall conform to type I or II, class 2, 1-1/8 inch circumference of MIL-R-1670. 3.2.13 Fasteners, slide, interlocking. The slide fasteners shall conform to Slide fastener chain shall be fabricated size H, wire stirrup pull of V-F-106. of
35、brass or polyester coil. the slider for the polyester coil shall be die cast zinc alloy. fastener tape shall be dyed to match olive drab shades S (CA 66519) and be water repellent and mildew-resistant, be tested for mildew resistance.) The color of the tape after treatment will be considered accepta
36、ble. The tape shall show good fastness to weathering. Alternatively, the slide fastener chain shall be polyester continuous monofilament in a ladder or coil type configuration. be Olive Drab or natural finish brass and the sliders shall be brass. Types and styles shall be as follows: The slider for
37、the brass chain shall be brass and The slide (Tapes made of 100 percent polyester need not Color of the chain shall a. For window, sidewall and stovepipe opening - Type I, style 2 slide fastener b. For blackout curtain and liner opening - Type III, style 1 slide fastener. 3.2.14 Grommet, metallic. T
38、he grommets shall conform to type III, class 3, sizes O, 4, and 5 of MIL-G-16491. 3.2.15 Plate, ridge. The ridge plates shall conform to type II and III of MIL-P-500 3.2.16 Rings, dee. The dee rings shall conform to either class 1 or 2, configuration K, size 1 by 3/4 inch of MIL-R-3390. 6 . Provided
39、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-LLLLG 3 6 977770b 0372002 5 6 MIL-T-1111G 3.2.17 Slips, tent line. The tent slips shall conform to type II of MIL-S-1734 3.2.18 Hooks, tent. The triangle eye hooks shall conform to type I, size 1- 1/2-inc
40、h of MIL-H-1608. 3.3 Construction. The construction shall conform in all respects to the drawings listed in section 2 and shali be as specified herein. 3.3.1 Stitching, machine. 3.3.1.1 Types of stitching. All stitch types, except bartacking, shall conform to FED-STD-751 as follows: For tent, screen
41、s and cover: For all stitching except stitching - Type 30 indicated by llZ1l on drawings, and inch alternatively for attachments of slide fasteners For stitching indicated by llZ1l on drawings and for attachments of slide fasteners For liner: For all stitching, except stitching indicated by rtZll on
42、 drawings For stitching indicated by IZf1 on drawings and alternatively for attachments of slide fasteners , 5 to 7 stitches per - Type 401, 5 t 7 stitches per inch. Chain portion of stitching shall not appear on outside of tent, screens or cover. - Type 301, 6 to 8 stitches per inch - Type 401, 6 t
43、o 8 stitches per inch. Chain portion of stitching shall not appear on outside of liner. For bartacking: - Bartack, 1/2 (+1/8, -1/16) inch long with 1/8 inch bight and shall contain 28 stitches 3.3.1.2 Type 30T.stitching. Ends of all stitching shall be backstitched or oversfitched 1/2 inch minimum ex
44、cept when caught in other stitching or turned under in a hem. Thread tension shall be maintained so that there will be no loose stitching resulting in puckering of material sewn. The lock shall be embedded in the material sewn. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted w
45、ithout license from IHS-,-,- MIL-T-LLLLG 83 m 777970b 0372003 7 MIL-T-1111G 3.3.1.2,l Repairs of type 301 stitching. Repairs of type 301 stitching shall be as follows: a. When thread breaks or bobbin run-outs occur during sewing, the stitching shall be repaired by restarting the stitching a minimum
46、of 1 inch behind the end of the stitching. - I/ b. Thread breaks or two or more consecutive skipped or run-off stitches noted during inspection of the item (in-process or end item) shall be repaired by overstitching. The stitching shall start a minimum of 1 inch before the defective area (1/2 inch o
47、n box, box and cross, and W-W stitching) and continue a minimum of 1 inch beyond the defective area onto the existing stitching. Loose or excessively tight stitching shall be repaired by removing the defective stitching, without damaging the materials, and restitching in the required manner. 1/ - 1/
48、 - When making the above repairs, the ends of the stitching are not required to be backstitched. 3.3.1.3 Type 401 stitching. Thread tension shall be maintained so that there will be no loose stitching. Both ends of seams or stitching produced with a 401 stitch type, when not turned under a hem or he
49、ld down by other stitching, shall have a 3/4 to 1 inch chain extending beyond each end. The looper (under thread) shall always be on the inside of the tent or cover. All repairs shall be made in accordance with 3.3.1.2.1a or 3.3.1.2.1b. 3.3.1.4 Automatic stitching. Automatic stitching machines may be used to perform any of the required stitch patterns provided the requirements of the stitch pattern, stitches per inch, size and
