1、1. 00-I-675F 35 777777V 0024628 b W /c- ss-m 00-1-675F November 20, 1973 SUPERSEDING Fed. Spec. 00-I-675E September 9, 1970 FEDERAL SPECIFICATION IROYERS , RATMORK, COXMERCIAL (AND ACCESSORIES) This specification was approved by the Connnissioner, Federal Supply Service, General Services Administrat
2、ion, for the use of all Federal agencies. 1. SCOPE AND CLASSIFICATION 1.1 Scope. This specification covers chest-type flatwork ironers, ventilating canopies, folding machines, combination spreader-feeder machine, crossfolders, and stacker. 1.2 Classification. 1.2.1 Sizes. Flatwork ironers shall be o
3、f the following sizes, as specified (see 6.2): Size 2 - 6 rolls (see table I). Size 3 - 8 rolls. 1.2.2 Accessory items. Accessory items shall be of the following items, types, styles, sizes, and models specified (see 6.2): Item 1 - Ventilating canopy (see 3.7.1). Item 2 - Crossfolder (see 3.7.2). It
4、em 3 - Folding machine (see 3.7.3)- Type I - Large and small piece flatwork (see 3.7.3.1)- Style A - Single lane. Sty1e.B - Automatic adjusting two lanes. Style C - Automatic adjusting four lanes. Type II - Small piece flatwork (see 3.7.3.2). Item 4 - Folding machine with built-in crossfolder (see 3
5、.7.4). Style A - Single lane. Style B - Multi-lane. FSC 3510 7 = THIS DOCUMENT CONTAINS 3/ PAGFT. - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-00-1-675F 35 777777L1 002Lib27 00-I-675F Item 4A - Combination folder (multi-lane) , crossfolder (mult
6、i-lane) Item 4B - Combination folder (single-lane), crossfolder (single-lane) , Item 5A - Combination spreader and feeding machine (see 3.7.6). and stacker (see 3.7.5). and stacker (see 3.7.5). Size 1 - (See 3.7.6.1). Size 2 - (See 3.7.6.2). Item 6 - Stacker, flatwork, small piece (see 3.7.7). 2. AP
7、PLICABLE DOCUMENTS 2.1 The following documents, of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein: Federal Specifications: CC-M-636 - Motor, Alternating-Current, (Fraccional Horsepower). CC-M-641 - Motor, A
8、lternating-Current, (Integral Horsepower, 200 Hp and Smaller). Federal Standard: FED-STD-123 - Marking for Domestic Shipment (Civil Agencies). (Activities outside the Federal Government may obtain copies of Federal Specifications, Standards, and Handbooks as outlined under General Informa- tion in t
9、he Index of Federal Specifications and Standards and at the prices indicated in the Index. The Index, which includes cumulative monthly supplements as issued, is for sale on a subscription basis by the Superin- tendent of Documents, U.S. Government Printing Office, Washington, DC 20402. (Single copi
10、es of this specification and other FederalSpecificatons required by activities outside the Federal Government for bidding purposes are available without charge from Business Service Centers, at the General Services Administration Regional Offices in Boston, New York, Washington, DC, Atlanta, Chicago
11、, Kansas City, MO, Fort Worth, Denver, San Francisco, Los Angeles, and Seattle, WA. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-00-I-b75F 35 9999974 0024630 Li = 00-I-675F (Federal Government activities may obtain copies of Federal Specificatio
12、ns, Standards, and Handbooks and the Index of Federal Specifications and Standards from established distribution points in their agencies .) Hilitary Specifications : MIL-T-152 - Treatment, Moisture and Fungus Resistant of Comunica- tions, Electronic, and Associated Electrical Equipment. Laundry and
13、 Dry Cleaning Machinery and Equipment (For Fixed Installations), Preparation for Delivery Of. NIL -L- 31 5 3 MIL-P-43219 - Paddings and Covers for Flatwork, Ironer Roll. - Military Standards: MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking for Shipment and Storag
14、e. MIL-STD-461 - Electromzignetic Interference Characteristics, MIL-STD-462 - Electromagnetic Interference Characteristics, Attributes. Requirements f o r Equipment. Measurement Of. (Copies of Military Specifications and Standards required by the supplier in connection with specific procurement func
15、tions should be obtained from the procuring act2vity or as directed by the contracting officer.) LAWS AND REGULATIONS 29 CFR 1910 - OCCUPATIONAL SAFETY AND HFATH ACT (OSHA) STANDARDS (The code of Federal Regulations (CFR) and Federal Register (FR) are for sale on a subscription basis by the Superint
16、endent of Documents, US Government Printing Off ice, Vashington, DC When indicated, reprints of certain regulations may be obtained from. the Federal agency responsible for issuance thereof. ) 20402. 2.2 Other publications. The following documents form a part of this specification to the extent spec
17、ified herein. Unless a specific issue is identified, the issue in effect on date of invitation for bids or request for proposal shall apply: National Electrical Manufacturers Association (NEMA) Standard : ICs-1970 - Industrial Controls and Systems (Appliiation for copies should be addressed to the N
18、ational Electrical Manufacturers Association, 155 East 44th Stret, New York, NY 10017.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-00-I-675F 35 W 777777L1 0024631 b W 00-I-675F Underwriters Laboratories (UL) Inc. Standards: (Application for co
19、pies of applicable standards should be addressed to the Underwriters Laboratories, Inc., 207 East Ohio Street, Chicago, IL 1285 Walt Whitman Road, Melville, L.I., NY Santa Clara, CA 95050.) 60611; 11749; 1655 Scott Boulevard, National Fire Protection Association (NFPA) Standard: No. 70 - The Natioqa
20、l Electrical Code (Appli ation for copies should be addressed to the National Fire Pro-ection Association, 60 Batterymarch Street, Boston, MA 02110.) American Welding Society (AWS) Standard: Qualification Procedure of the American Welding Society (Application for copies should be addressed to the Am
21、erican Welding Society, 10017.) 345 East 47th Street, New York, NY American Society. of Mechanical Engineers (MME) Standard: Boiler and Pressure Vessel Code, Section VIII, Unfired Pressure Vessels Welding Qualifications of the American Society of Mechanical Engineers (Application for copies should b
22、e addressed to the American Society of Mechanical Engineers, 345 East 47th Street, New York, NY 10017.) (Technical society and technical association specifications and standards are generally available for reference from libraries. uted among technical groups and using Federal agencies.) They are al
23、so distrib- 3. RFIQUIREMENTS 3.1 First article. When specified (see 6.2), the supplier shall furnish a sample of the item to be procured under this specification for first article inspection and approval (see 4.3 and 6.5). 3.2 Standard product. The ironers and accessories delivered under this specif
24、ication shall be the manufacturers commercial product, except for any changes necessary to comply with -specification requirements. furnished on any one contract, including parts and subassemblies thereof shall be new and interchangeable. All like items 4 Provided by IHSNot for ResaleNo reproduction
25、 or networking permitted without license from IHS-,-,-00-I-675F 35 9 777777LI 0024632 B 00-I-675F 3.3 Codes and standards. The ironers and accessories shall comply with the applicable requirements of NEMA ICs-1970, UL, NETA No. 70, and OSHA 29 CFR 1910. 3.3.1 Compliance. Prior to approval of the fir
26、st article, if one is submitted, or prior to commencing production, the supplier shall submit to the contracting officer or his authorized representative satisfactory evidence that the ironers and accessory item that he proposes to furnish under this specification meet the applicable requirements of
27、 NEMA ICs-1970, UL, NFPA No. 70 and OSZU. 4 3.3.1.1 NEEN. Acceptable evidence of meeting the requirements of NEMA shall be a certificate of compliance certifying that motor controllers, switches, relay and time delays conform to NEMA ICs-1970. 3.3.1.2 UL. Acceptable evidence of meeting the requireme
28、nts of -UL shall be a certificate of compliance certifying that the wiring, fittings and conduit conform to the applicable UL standard for use in non-hazardous locations. 3.3.1.3 NFPA. Acceptable evidence of meeting the requirements of NFPA shall be a certificate of compliance certifying that ironer
29、s and accessories wiring conforms to NFPA No. 70. 3.3.1.4 OSW. Acceptable evidence of meeting the applicable safety and health standards of OSHA shall be a certificate of compliance certifying that the ironers and accessories furnished conform to OSHA 29 CFR 1910 264 (ii) (a). 3.4 Materials and comp
30、onents. Materials and components shall be as specified herein. Materials not definitely specified shall be of the quality normally used by the manufacture in his standard commercial ironer or accessory provided that the completed item complies with all provisions of this specification. 3.4.1 Pipe, t
31、ube, fittings, traps, and valves. Pipe, tube, fittings, traps, and valves used for air, steam, and condensate lines shall comply with accepted plumbing practice. 3.4.2 Conduit, fittings, and electric wire. Electrical conduit shall be electrical metallic tubing or flexible metallic conduit. All elect
32、ric wire shall be stranded copper, heat-resistant grade, thermplastic insulated. Solid (nonstranded) wire shall not be used. 5 PROBLEM HARD COPY - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-00-I-b75F 35 W 7979974 002Li633 T W 00-I-675F 3.4.3 Xot
33、ors. Motors shall conform to the requirements of CC-1.1-636 or CC-Ei-641, as applicable, and shall conform to the following requirements: (a) All motors shall have windings impregnated to resist moisture, (b) Each motor shall have the proper starting characteristics, ample power, and adequate therma
34、l dissipation capacity to comply with requirements specified herein, with a reasonable actor of safety, com-ensurate with the application and expected duty cycle to which each motor might be subjected under normal operating conditions. Motors shall be equipped with ball bearings, except that motors
35、of 1/2 horsepower (hp) or less when usad in horizontal applications may have sleeve bearings. * (c) . (d) Motor bearings shall be. of the permanently lubricated type or shall have adequate and accessible means for lubrication. (e) Each motor of 1/8 hp rating or larger shall be provided with thermal-
36、 overload protection jncorporated as a part of the notor or installed in the controller. 3.4.4 I_ Yotor control circuit. Each motor on ironers and accessory items, as applicable, shall be provided with a controller of the magnetic across- the-line type having a separate pole for each ungrounded cond
37、uctor:. for direct current motors of more than 1/2 hp shall be of the reduced voltage type having one or more steps of annature resistance for smooth acceleration. Pushbutton control stations shall be mounted at points convenient to the operator. operation. and indicating lights shall be provided to
38、 perform the intended functions. Controllers Pushbuttons shall be protected or recessed to prevent accidental Timers, limit sritches, remote control pushbutton switches , signals, 3.4.5 Belts and pulleys. V-belts shall be of the grade commercially known as multiple-drive type except where a single b
39、elt is used with a fractional- horsepower motor, a V-belt commercially knotm as a fractional-horsepower belt may be supplied. Pulleys for V-belts shall be suitably grooved and shall not be a die cast type when used in powered drive. of the silent or roller-chain type. Chain type belts shall be Belt
40、and chain eension shall be adjustable. 6 .F PROBLEM HARO C-PYI Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-00-1-6 75F 3.5 Desim and construction. The completely assembled items shall show that the assembly of components as applicable to the parti
41、cular item has: (a) complete and proper interrelationship; (b) moving parts evidence no overheating; and (c) starting and stopping devices operate smoothly and positively. tested as specified in 4.7.2. These requirements shall be determined when the equipment is 3.5.1 Electrical characteristics. The
42、 electrical parts of the machines shall be suitable for the voltage, frequency, and number of phases for alternating current (AC) and voltage for direct current (DC) as specified (see 6.2). 3.5.2 Wiring and instructions. Wiring shall be installed in conduit which shall be provided between ail compon
43、ents mounted on the equipment. shall be installed with materials specified in 3.4.2, as applicable, except metallic armored cable may be used where required to allow for belt, or other drive adjustment. Ail wiring shall terminate in a connection box with pro- visions for connections beyond the machi
44、nes. Wiring and connection diagrams, including instructions for connecting controllers to be mounted separately from the equipment shall be furnished with the end item. Wiring 3.5.3 Safety devices. Belts, ribbon feeds, chains, shafts, pulleys, and gears shall be enclosed or guarded to prevent operat
45、or injury. be cast iron or sheet metal. without disassembling pipes or fittings on the machine. access openings with covers over parts requiring adjustment or lubrication. Guards shall All parts of the guard shall be removable There shall be 3.5.4 Equipment base. When specified (see 6.2),- the equip
46、ment base shall There shali be provisions for anchoring be provided with a leveling device. the base to the floor, and anchor bolts shall be furnished. 3.5.5 Working pressure. Cylinders, chests, and chambers using steam shall be designed for a working pressure of 125 pounds per square inch gage (psi
47、g) steam and shai.1 be capable of withstanding a hydrostatic pressure established in accordance with the provisions of the ASEE Unfired Pressure Vessel Code when tested as specified in 4.7.1. 3.5.6 Gears and sprockets. Gears and sprockets shall have machined teeth. The use of die-cast gears or sproc
48、kets shall not be permitted on any powered drive. Gears shall be of ferrous or aluminum bronze material and sprockets shall be of ferrous metal. Noise reducing material of phenolic laminate may be used for drive and intermediate pinions. All pinions shall have faces at least as wide as the gears wit
49、h which they mesh. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-00-I-675F 35 W 999997Li 0024635 3 W . _ 00-I-675F 3.5.7 Bearings and lubrication. Removable, aluminum bronze sleeve, ball, or roller bearings shall be provided for all shafts, rolls, and studs. Bear- ings shall be replaceable and shall be permanently lubricated unless oil cups or pressure grease fittings are pro
