1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 3646-007 Edition P 2 May 2014 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: 49.060 Supersedes edition P 1
2、of November 2001 and will supersede EN 3646-007:2006 Descriptors: Aeronautical industry, aircraft equipment, electrical connection unit, electrical connector, characteristics marking ENGLISH VERSION Aerospace series Connectors, electrical, circular, bayonet coupling, operating temperature 175 C or 2
3、00 C continuous Part 007: Receptacle, hermetic, round flange, welding or brazing mounting Product standard Srie arospatiale Connecteurs lectriques circulaires accouplement par baonnettes, temprature dutilisation 175 C ou 200 C continu Partie 007 : Embase hermtique, collerette ronde, fixation par sou
4、dure ou brasure Norme de produit Luft- und Raumfahrt Elektrische Rundsteckverbinder mit Bajonettkupplung, Betriebstemperatur 175 C oder 200 C konstant Teil 007: Hermetischer fester Steckverbinder mit rundem Schwei- oder Ltflansch Produktnorm This “Aerospace Series“ Prestandard has been drawn up unde
5、r the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publ
6、ication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft Eur
7、opean Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standar
8、ds conflicting with the EN. Edition approved for publication 1st May 2014 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2014 by ASD-STAN prEN 3646-007:2014 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Terms and
9、definitions . 3 4 Required characteristics . 3 5 Designation 5 6 Marking . 6 7 Technical specification . 6 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in
10、 ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 3646-007:2014 (E) 3 1 Scope This standard defines the characteristics of hermetic receptacle with round flange attached by welding or brazing in the family of bayonet coupling circular connectors, intended f
11、or use in an operating temperature range of 65 C to 175 C or 200 C continuous. It applies to models defined in Table 3. For plugs and protective covers see EN 3646-008 and EN 3646-009 respectively. 2 Normative references The following documents, in whole or in part, are normatively referenced in thi
12、s document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3646-001, Aerospace series Connectors, electrical, circular, bayonet coupling, oper
13、ating temperature 175 C or 200 C continuous Part 001: Technical specification EN 3646-002, Aerospace series Connectors, electrical, circular, bayonet coupling, operating temperature 175 C or 200 C continuous Part 002: Specification of performance and contact arrangements EN 3646-008, Aerospace serie
14、s Connectors, electrical, circular, bayonet coupling, operating temperature 175 C or 200 C continuous Part 008: Plug Product standard EN 3646-009, Aerospace series Connectors, electrical, circular, bayonet coupling, operating temperature 175 C or 200 C continuous Part 009: Protective cover for recep
15、tacle Product standard 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 3646-001 apply. 4 Required characteristics 4.1 Dimensions and mass See Figure 1 and Table 1. Dimensions and tolerances are in millimetres, they apply after surface treatment. Inter
16、face mating dimensions, see EN 3646-001. prEN 3646-007:2014 (E) 4 Key 1 Polarizing strip optional colour 2 Panel Figure 1 Table 1 Housing size L M N P R Mass g 0,5 0,15 max. 0,02 0,13 max. max. 08 11,50 2,40 10 14,27 16,10 5 10 17,07 19,30 8 12 19,84 21,70 1214 23,01 24,90 1516 26,19 28,10 1818 29,3
17、6 31,20 2420 13,50 31,75 33,80 28 22 3,20 11 34,92 36,80 34 24 13,90 38,10 40,00 46 prEN 3646-007:2014 (E) 5 4.2 Panel cut-out Recommended panel cut-out dimensions: see Figure 2 and Table 2. Dimensions and tolerances are in millimetres. Figure 2 Table 2 Housing size A D 0,25 0 min. 08 14,79 32 10 17
18、,59 35 12 20,36 38 14 23,53 41 16 26,71 45 18 29,88 47 20 32,27 51 22 35,42 53 24 38,60 57 4.3 Material and surface treatment See Table 3. 4.4 Main general characteristics See EN 3646-002. 4.5 Possible combinations of plugs and receptacles See EN 3646-002. prEN 3646-007:2014 (E) 6 5 Designation EXAM
19、PLE Description block CONNECTOR, ELECTRICAL, RECEPTACLE Identity block EN3646Y11006MN Number of the basic standard Model (see Table 3) Hermetic receptacle with round flange (see EN 3646-002) Housing size and contacts arrangement (see EN 3646-002) Type of contact M male Polarization (see EN 3646-002)
20、 NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. Table 3 Connectors models Model DescriptionY Hermetic receptacle with housing (shell) in passivated stainless steel, solder contacts Maximum operating temperature 200 C continuous 6 Marking Unles
21、s there are other specific contractual requirements, the marking shall include. 6.1 Marking on the product the manufacturers part number corresponding to the identity block as defined in Clause 5; the date of manufacture (year, week); the manufacturers name or trade mark. 6.2 Marking on the individual packaging the identity block as defined in Clause 5; the corresponding manufacturers part number; the date of manufacture (year, week); the manufacturers name or trade mark. 7 Technical specification See EN 3646-001.
