1、AECMA STANDARD NORME AECMA AECMA NORM prEN 4059 Edition P 2 September 2001 PUBLISHED BY THEUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES - STANDARDIZATION (AECMA-STAN) Gulledelle 94 - 6-1200 BRUXELLES - Tel. (+32) 2 775 8110 - Fax. (+32) 2 775 811 1 I cs: Descriptors: ENGLISH VERSION Aerospace series
2、Filler rods and filler wires for welding in steel Diameter 0,5 mm I D I5,O mm Dimensions Supersedes edition P 1 November 1997 Srie arospatiale Baguettes et fils dapport de soudage en acier Diamtres 0,5 mm I D I 5,O mm Dimensions Luft- und Raumfahrt Schweizusatzstbe und -drahte aus Stahl Durchmesser
3、0,5 mm I D I 5,O mm Mae This Aerospace Series“ Prestandard has been drawn up under the responsi needs of the European Aerospace Industry. It has been tech concerned Domain following member comments. Subsequent to the publication of extent that inferchangeabilify is After examinati not be changed to
4、an re-identification of the Replace page 1 of the previous edition by this page Nota - Extra copies can be supplied by B.N.A.E. - Technopolis 54 - 199. rue Jean-Jacques Rousseau - 92138 ISSY-LES-MOULINEAUX CEDEX Withdrawal approved 2001 -09-28 Comments should be sent within six months after the date
5、 of publication to Gulledelle 94 AECM A-STAN 6-1200 BRUXELLES Material Domain Mr Evetc I I aecma 20( - - - STD-AECMA PREN YO57-ENGL 1777 1OL23LL OOLLi227 AT7 D Page 3 prEN 4059: 1997 O Introduction This standard is part of the series of EN metallic material standards for aerospace applications. The
6、general organization of this series is described in EN 4258. 1 Scope This standard specifies the dimensions and tolerances of : Filler rods and filler wires for welding in steel Diameter 0,5 mm 5 D 55.0 mm for aerospace applications. 2 Normative references This European Standard incorporates by date
7、d or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard on
8、ly when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 4258 Aerospace series - Metallic materials - General organization of standardization - Links between types of EN standards and their use 1) 3 Form See figure 1. I
9、 Figure 1 1) Published as AECMA Prestandard at the date of publication of this standard Previous page is blank STD-AECMA PREN 4059-ENGL 1777 = 1012311 0034228 733 Page 4 prEN 4059: 1997 Rod Wire O, 5 0,6 03 03 03 4 Recommended dimensions and mass 0,20 O, 28 O, 50 0,64 4.1 Diameter and mass See table
10、 1. 1,6 2,o Table 1 1,6 2,01 158 210 3,14 247 Nominal D mm 2,4 3,O 3,2 4,O Section mm2 4,52 355 3,O 7,07 555 3,2 8,04 631 4,O 12,57 987 Diameter 0,8 I D I 5,O Linear mass 1) g/m Tolerance I0,l 16 22 39 50 62 I 1 f2 I 1 f2 I 1,13 1 89 I 5,O I 5,O I 19,63 I 1541 I 1) For information, calculated with a
11、 density of 7,85 kg/dm3 1 4.2 Length The order shall specify if bars are to be supplied in fixed or in random lengths. In the event of a supply of random lengths the minimum and maximum values for the lengths shall be specified on the order. Length of rods I 1 O00 mm. Length of wires : to be specifi
12、ed on the order. 5 Tolerances 5.1 Dimensional tolerances 5.1.1 Diameter 5.1.1.1 Rods See table 2. Table 2 Dimensions in millimetres STD-AECMA PREN 4059-ENGL 1797 LOL23LL 0014227 b7T Page 5 prEN 4059: 1997 Diameter 5.1.1.2 Wires See table 3. Tolerances Table 3 0,5 5 D o,a + 0,Ol - 0,03 ola 5 D 2,a + 0,Ol - 0,04 2,a I D I 5,o + 0,Ol - 0,07 5.1.2 Length Tolerances on length of rods : f 5 mm. 5.2 Geometric tolerances - Roundness Roundness shall be contained within the diameter tolerances.
