1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 4652-211 Edition P 1 January 2014 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONRue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.orgICS: Descriptors: ENGLISH VERSION
2、 Aerospace series Connectors, coaxial, radio frequency Part 211: Type 2, TNC interface Clamp nut assembly version Right angle plug Product standard Srie arospatiale Connecteurs coaxiaux pour radio frquences Partie 211 : Type 2, interface TNC Version presse toupe Fiche coude Norme de produit Luft- un
3、d Raumfahrt Hochfrequenz Steckverbinder, koaxial Teil 211: Typ 2, TNC Klemmverbindung Rechtwinkliger Kabelverbinder Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). I
4、t is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is af
5、fected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full E
6、uropean Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 January 2014 Comments should be sent within six mo
7、nths after the date of publication to ASD-STAN Electrical Domain Copyright 2014 by ASD-STAN prEN 4652-211:2014 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Terms and definitions . 3 4 Required characteristics . 3 5 Test methods . 7 6 Qualification . 9 7 Quality assurance 9 8 D
8、esignation 10 9 Marking . 10 10 Packaging . 10 11 Storage 10 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standa
9、rd has received approval for Publication. prEN 4652-211:2014 (E) 3 1 Scope This standard specifies the characteristics of screwed on coupling (TNC interface) coaxial right angle plugs 50 ohms. The cable to connector assembly is a clamp technology. 2 Normative references The following documents, in w
10、hole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591 1), Aerospace series Element
11、s of electrical and optical connection Test methods EN 2812, Aerospace series Stripping of electric cables EN 4652-001, Aerospace series Connectors, coaxial, radio frequency Part 001: Technical specification 2)EN 4652-212, Aerospace series Connectors, coaxial, radio frequency Part 212: Type 2, TNC i
12、nterface Clamp nut assembly version Square flange receptacle Product standard2)EN 4652-213, Aerospace series Connectors, coaxial, radio frequency Part 213: Type 1, TNC interface Clamp assembly version Bulkhead receptacle Product standard 3)EN 9133, Aerospace series Quality management systems Qualifi
13、cation procedure for aerospace standard parts TR 6058, Aerospace series Cable code identification list 4)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 4652-001 apply. 4 Required characteristics The connection technology shall comply to required test
14、s described in Clause 5. Interface shall comply to EN 4652-001. A self-locking device on plugs shall be proposed if hole for lockwire does not exist. Water ingress resistance is required in mated conditions for all cable groups. Water ingress resistance is required in unmated condition for cable gro
15、up A. 1) All parts quoted in this standard. 2) Published as ASD-STAN Prestandard at the date of publication of this standard. http:/www.asd-stan.org/ 3) In preparation at the date of publication of this standard. 4) Published as ASD-STAN Technical Report at the date of publication of this standard.
16、http:/www.asd-stan.org/ prEN 4652-211:2014 (E) 4 4.1 Configuration, dimension and mass Mass without heatshrink tubing. See Figure 1 and Table 1. Dimensions in millimetres Key 1 3 holes for lockwire 1 2 Marking 3 HEX. 14 4 Flat 10 5 HEX. F Figure 1 TNC right angle plug Marking: see Clause 9. Table 1
17、TNC right angle plug dimensions and mass Cable group B C D E HEX. F Interface style Mass (cable jacket) (cable conductor) (according to EN 4652-001) g max. max. max. max. A 43,0 7,8 2,3 15 12 Style C 46,9 B 33,8 5,55 1,4 13 8 Style C 35,2 prEN 4652-211:2014 (E) 5 4.2 Materials and finish Centre cont
18、act : Copper alloy gold plated over nickel undercoat Insulators : PTFE Seals . : Silicone rubber or silicone fluoride Body : Copper alloy, nickel plated Heat shrink tube . : Polyolefin Coupling nut, rear screw and other parts materials shall have mechanical and electrical characteristics consistent
19、with the requirements of this product standard. 4.3 Temperature Operating temperature shall be between 65 C and 165 C. 4.4 Electrical characteristics Maximum operating frequency . : 6 GHz VSWR . : 1,15 max. from DC to 3 GHz 1,20 max. from 3 GHz to 6 GHz Impedance : 50 Insertion loss : 0,07f dB max.,
20、 f in GHz Contact resistance (initial centre contact) : 2,0 m max. Insulation resistance . : 5 000 M min. Withstand voltage . : 1 500 Veff (at sea level) 4.5 General characteristics Tightening torque of coupling nut . : 2,6 Nm 0,3 Nm Force to engage or disengage . : 0,23 Nm max. Service life : 500 c
21、ycles Retention of centre contact : 27 N min. Retention of cable . : see Table 2. Table 2 Retention of cable Cable group Retention of cable N min. A 180 B 180prEN 4652-211:2014 (E) 6 4.6 Admissible cables, tools and stripping lengths See Table 3 to Table 5. Table 3 Stripping lengths Cable group Cabl
22、e code (see TR 6058) Stripping Lengths mm A KW B KX Table 4 Stripping lengths cable group A A B min. mm max. mm min. mm max. mm 4,6 5,4 8,6 9,4 Table 5 Stripping lengths cable group B A B min. mm max. mm min. mm max. mm 3,6 4,4 7,6 8,4 For stripping see EN 2812. prEN 4652-211:2014 (E) 7 5 Test metho
23、ds See Table 6. Table 6 Test methods (1 of 3) EN 2591- Designation of the test Details 101 Visual examination Applicable 102 Examination of dimensions and mass TNC interface Style A: see 4.1 and EN 4652-001. TNC interface Style B: see 4.1 and EN 4 652-001. TNC interface Style C: see 4.1 and EN 4 652
24、-001. The manufacturer shall precise which style of interface is used. 201 Contact resistance - low level Applicable on centre contact 202 Contact resistance at rated current 2,0 m max. initial centre contact and 2,5 m max. after test For nickel plated connectors: 0,4 m max. initial external contact
25、 and 2,0 m max. after test 204 Discontinuity of contacts in the microsecond range Duration of micro discontinuity: 1s Method B Test time: throughout duration of tests EN 2591-402 and EN 2591-403. 206 Measurement of insulation resistance 5 000 M min. 207 Voltage proof test Method A Pressure Mated aUn
26、mated aSea level 1 500 1 500 12,1 kPa 800 550 4,7 kPa 375 350 2,7 kPa 250 200 aValues in Volts RMS. 212 Surface transfer impedance Applicable (up to 100 MHz) 3 m 1 MHz 1 m 10 MHz 3 m 30 MHz 5 m 100 MHz 214 Lightning strike, current and voltage pulse 10 kA wave form 5 A, 10 A RMS 221 Voltage Standing
27、 Wave Ratio (VSWR) Method B VSWR 1,15 from DC to 3 GHz VSWR 1,20 from 3 GHz to 6 GHz. prEN 4652-211:2014 (E) 8 Table 6 Test methods (2 of 3) EN 2591- Designation of the test Details 222 Insertion Loss (I.L.) 0,07f dB max., f in GHz Measurement shall be performed with connector mated with EN 4652-212
28、 or EN 4652-213 receptacle from same technology and cable group 223 Measurement of characteristic impedance of a coaxial connector or contact 50 5 at 200 MHz Input impedance 224 RF leakage Measured from 2 GHz to 3 GHz 50 dB for connectors on cable group A 60 dB for connectors on cable group B 225 RF
29、 high potential withstanding voltage 1 000 V at 5 MHz 226 Corona level Corona extinction voltage 315 V rms at 4,4 kPa (70000 feet altitude) 303 Cold/low pressure and damp heat Five (5) cycles Minimum temperature 60 C 305 Rapid change of temperature Mated connectors TA 05165 C; TB 5065 C. 307 Salt mi
30、st The connectors shall be suspended in the test chamber with non-metallic cords, so that no accumulation of condensed saline solution can occur. The connectors shall be: subjected to 50 cycles of mating and unmating at a rate 5 cycles/min.; exposed to the salt mist: mated for 240 h not exposed to t
31、he salt mist: unmated for 48 h 308 Sand and dust The mated connectors shall be arranged so that their longitudinal axis is parallel to the wind direction, with the rear of the plug facing the wind. Wind velocity in the duct: (3,5 0,5) m/s Number of cycles: one (1) 311 Low air pressure Refer to test
32、EN 2591-207. 314 Immersion at low air pressure Specimen without heat shrinkable tube In unmated condition (applicable only for connectors on cable group A): After the three (3) cycles, remove the specimen from salt water, clean the interface with soft paper. In mated condition (applicable for all co
33、nnectors): standard procedure. prEN 4652-211:2014 (E) 9 Table 6 Test methods (3 of 3) EN 2591- Designation of the test Details 315 Fluid resistance See EN 4652-001. 317 Flammability Method A 402 Shock Method A Half sine Severity 30 g, duration 11 ms Number of shocks: one (1) in each way for each of
34、the three (3) axis (six (6) shocks in all) 403 Sinusoidal and random vibration Method A: sinusoidal vibration with the following individual modalities: Level 2 50 Hz to 70 Hz : 1,5 mm double amplitude 70 Hz to 2 000 Hz : 20 g Three (3) axis or two (2) axis (straight connectors) Duration 4 h per axis
35、 at ambient temperature 404 Transverse load Applicable on rear of plug; torque moment 15 Nm 406 Mechanical endurance 500 cycles 408 Mating and unmating forces 0,23 Nm max. 409 Contact retention in insert 27 N min., applicable on cabled specimen 417 Tensile strength (crimped connection) See Table 2.
36、418 Gauge insertion/extraction forces (female contacts) Not applicable 422 Locking wire hole strength Applicable 507 Plating porosity Applicable 508 Measurement of thickness of coating on contacts Applicable 509 Adhesion of coating on contacts Applicable 513 Magnetic permeability 2 6 Qualification Q
37、ualification test programme: see EN 4652-001. 7 Quality assurance See EN 9133. prEN 4652-211:2014 (E) 10 8 Designation EXAMPLE Description block CONNECTOR, COAXIAL Identity block EN4652-211A50 Number of the basic standard Connector interface type code (see EN 4652-001) 2 TNC Technology of assembly c
38、ode (see EN 4652-001) 1 clamp Connector model code (see EN 4652-001) 1 right angle plug Cable group code (see Table 3) Impedance: 50 50 NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 9 Marking See EN 4652-001 10 Packaging See EN 4652-001. 11 Storage See EN 4652-001.
