1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM ASD-STAN prEN 4806 Edition P 1 December 2015 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8131 - www.asd-stan.orgICS: Descriptors: ENGL
2、ISH VERSION Aerospace series Flange couplings Weld coupling, straight, in nickel alloy Inch series Luft- und Raumfahrt Rohrverschraubung mit Flanschen und Schweistutzen, gerade, aus Nickellegierung Inch-Reihe Srie arospatiale Raccordement bride Raccord souder, droit, en alliage de nickel Srie en inc
3、hes This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the conc
4、erned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and for
5、mal agreement of ASD-STAN, the ASD-STAN prEN will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the
6、 EN the status of a national standard and by withdrawing any national standards conflicting with the EN. ASD-STAN Technical Committee approves that: “This document is published by ASD-STAN for the needs of the European Aerospace Industry. The use of this standard is entirely voluntary, and its appli
7、cability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” ASD-STAN reviews each standard and technical report at least every five years at which time it may be revised, reaffirmed, stabilized or cancelled. ASD-STAN
8、invites you to send your written comments or any suggestions that may arise. All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior wri
9、tten permission of ASD-STAN. Order details: E-mail: salesasd-stan.org Web address: http:/www.asd-stan.org/ Edition approved for publication 1stDecember 2015 Comments should be sent within six months after the date of publication to ASD-STAN Mechanical Domain Copyright 2016 ASD-STAN prEN 4806:2015 (E
10、) 2 Contents Page Foreword .2 1 Scope .3 2 Normative references .3 3 Required characteristics 3 4 Designation .5 5 Identification marking 5 6 Technical specification 5 7 Quality Assurance 6 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Mechanical Domain. After
11、inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4806:2015 (E) 3 1 Scope This standard specifies the characteristics of straight welded coupling in nickel alloy for swivel f
12、lange couplings for inch series aerospace applications. Nominal pressure: The parts shall withstand nominal pressures given in Table 1. The nominal pressure of the assembly depends on associated seal, tube material characteristics, tube diameter and tube wall thickness (see EN 4814). NOTE Assembly i
13、n accordance with TR 4815. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced do
14、cument (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products EN 2516, Aerospace series Passivation of corrosion resisting steels and decontamination of nickel base alloys EN 3671, Aerospace series Heat resisting alloy NI-PH3601 (NiCr22Mo9Nb) Non heat treated For
15、ging stock a or D 250 mm EN 4379, Aerospace series Heat resisting alloy NI-PH3601 (NiCr22Mo9Nb) Solution treated, forging De 200 mm EN 4380, Aerospace series Heat resisting alloy NI-PH3601 (NiCr22Mo9Nb) Solution treated Bar and section De 200 mm 1) EN 4814, Aerospace series Flange couplings, up to 2
16、1 000 kPa Technical specification Inch series 1) EN 9100, Quality Management Systems Requirements for Aviation, Space and Defense Organizations TR 4815, Aerospace series Flange couplings, up to 21 000 kPa Design standard Inch series 2) 3 Required characteristics 3.1 Configuration Dimensions Toleranc
17、es Masses See Figure 1 and Table 2. Dimensions and tolerances are in millimetres, except otherwise specified. 3.2 Material and surface treatment EN 4380 or EN 3671 or EN 4379 Surface finish: Passivation EN 2516 1) Published as ASD-STAN Prestandard at the date of publication of this standard. (http:/
18、www.asd-stan.org/) 2) Published as ASD-STAN Technical Report at the date of publication of this standard. (http:/www.asd-stan.org/) prEN 4806:2015 (E) 4 Key 1 3D view (for information only) 2 Marking of identity block 2 Marking of manufacturers monogram Figure 1 Ramax 3,2 0,3 0,1 Ramax 0,8 prEN 4806
19、:2015 (E) 5 Table 1 Dimensional code a Nominal diameter Wall thickness of tube A B D E F V Mass b inch mm min max 0,1 0 min max min max 0 0,4 A10 .625 15,875 0,711 28,45 28,60 14,38 12,45 12,95 2,80 3,05 19,70 EN4549A010 16,40 B10 0,889 13,95 EN4549B010 A12 .750 19,050 0,711 31,60 31,75 17,55 12,70
20、13,20 2,80 3,05 23,80 EN4549A012 19,00 B12 0,889 17,10 EN4549B012 A16 1.000 25,400 0,711 38,00 38,10 23,90 13,20 14,20 2,80 3,05 30,20 EN4549A016 28,10 B16 0,889 23,45 EN4549B016 A20 1.250 31,750 0,711 46,70 46,85 30,25 13,70 14,20 3,05 3,20 36,50 EN4549A020 37,80 B20 0,889 29,80 EN4549B020 A24 1.50
21、0 38,100 0,711 53,85 54,00 36,60 14,20 14,75 3,30 3,45 42,00 EN4549A024 47,10 B24 0,889 36,15 EN4549B024 A28 1.750 44,450 0,711 60,20 60,35 42,95 14,75 15,25 3,55 3,70 49,60 EN4549A028 59,20 B28 0,889 42,50 EN4549B028 A32 2.000 50,800 0,711 69,70 69,85 49,30 14,75 15,25 3,55 3,70 56,00 EN4549A032 77
22、,30 B32 0,889 48,90 EN4549B032 a This code is composed with the following elements: Tube wall thickness code (A: 0,711 mm; B: 0,889 mm); Nominal diameter given in 16th of inches within 2 digit. b Mass quoted in kg/1 000 parts. 4 Designation EXAMPLE Description block COUPLING, STRAIGHT, WELD Identity
23、 block EN4806-A10 Number of this standard Dimensional code (see Table 1) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 5 Identification marking EN 2424, category A, as indicated on Figure 1. 6 Technical specification See EN 4814. prEN 4806:2015 (E) 6 7 Quality Assurance Approval of the manufactures See EN 9100
