1、ASD-STAN Technical Report Rapport Technique ASD-STAN ASD-STAN Fachbericht TR 4837 Edition 1 September 2014 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONRue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.orgICS: Descrip
2、tors: ENGLISH VERSION Aerospace series Applicable crimping tools for electrical contact product standards EN 3155-003, EN 3155-008 and EN 3155-009 for contact size # 10 and barrel size # 10 only Srie arospatiale Outil de sertissage applicable aux les normes produits EN 3155-003, EN 3155-008 et EN 31
3、55-009 pour contact taille # 10 et ft taille # 10 seulement Luft- und Raumfahrt Anzuwendende Crimpwerkzeuge fr elektrische Kontakte der Produktnormen EN 3155-003, EN 3155-008 und EN 3155-009, nur fr Kontaktgre #10 und Hlsengre #10 This Technical Report was drawn up by the Electrical Domain of ASD-ST
4、AN. The reason which led to the publication of the document as a Technical Report is explained in the foreword. Edition approved for publication 1stSeptember 2014 Electrical Domain Copyright 2014 by ASD-STAN Page 2 TR 4837:09-2014 Contents Page Foreword 3 0 Introduction 4 1 Scope 4 2 Normative refer
5、ences 4 3 Terms and definitions .5 4 Required characteristics .5 Page 3 TR 4837:09-2014 Foreword The main task of ASD-STAN Technical Committees is to prepare EN Standards, in exceptional circumstances however, the publication of Technical Report of one of the following types may be proposed: Type 1,
6、 the subject is still under technical development requiring wider exposure; Type 2, a Technical Committee has collected data of a different kind from that which is normally published as a European Standard. The Electrical Domain decided to publish this document in the form of a Technical Report of t
7、ype 2 in order to facilitate the updating of this document. Page 4 TR 4837:09-2014 0 Introduction The aim of this Technical Report is to provide and specify the applicable tools for crimping the product standard EN 3155-003, EN 3155-008 and EN 3155-009 on contact size # 10 and barrel size # 10 only
8、until to obtain the standardisation and publication of the appropriate tool product standards EN 4008. 1 Scope This standard specifies necessary characteristics for: The die set and the locator used with the pneumatic tool reference MIL-C-22520/23-01, The locator and the selector used with manual to
9、ol reference M300BT, to crimp the electrical contact EN 3155-003, EN 3155-008 and EN 3155-009 on contact size # 10 and barrel size # 10 only. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. Fo
10、r dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2083, Aerospace series Copper or copper alloy conductors for electrical cables Product standard EN 2591-100, Aerospace series Elements of e
11、lectrical and optical connection Test methods Part 100: General EN 3155-003, Aerospace series Electrical contacts used in elements of connection Part 003: Contacts, electrical, female, type A, crimp, class S Product standard 1)EN 3155-008, Aerospace series Electrical contacts used in elements of con
12、nection Part 008: Contacts, electrical, male, type A, crimp, class S Product standard 1)EN 3155-009, Aerospace series Electrical contacts used in elements of connection Part 009: Contacts, electrical, female, type A, crimp, class S Product standard 1)EN 4008 (all parts), Aerospace series Elements of
13、 electrical and optical connection Crimping tools and associated accessories EN 4434, Aerospace series Copper or copper alloy lightweight conductors for electrical cables Product standard (Normal and tight tolerances) MIL-C 22520/23-01, Crimping tools, terminal, hand or power actuated, wire terminat
14、ion, pneumatic tool for wire barrel sizes 0000 through 8 2)1) Published as ASD-STAN Prestandard at the date of publication of this standard (www.asd-stan.org) 2) Published by: DoD National (US) Mil. Department of Defense http:/www.defenselink.mil/ Page 5 TR 4837:09-2014 3 Terms and definitions For t
15、he purposes of this document, the terms and definitions given in EN 2591-100 apply. 4 Required characteristics The selector number used for crimping copper or copper alloy conductors in cables EN 2083 and EN 4434 are indicated in Table 1. It is the responsibility of the user if the parameters in Tab
16、le 1 are changed for service use. Table 1 Contact Contact Cable size M22520/23-01 (Pneumatic Tool) M300BT (Manual Tool) Product standard Contact size Barrel size ASD code AWG a Die set Locator Locator SelectorEN 3155-003 EN 3155-008 EN 3155-009 10 10 030 12 DMC tool: WA23-168DA DMC tool: WA23-102L DMC tool:TP1526 2 10 10 051 or 050 10 DMC tool: WA23-101DA DMC tool: WA23-102L DMC tool:TP1526 4 PICO tool: 414 DA-10N PICO tool: 4536 aAWG Closest American Wire Gauge.
