1、ANSI/ASHRAE/ASHE Addendum hto ANSI/ASHRAE/ASHE Standard 170-2013Ventilation ofHealth Care FacilitiesApproved by ASHRAE on May 31, 2016; by the American Society for Healthcare Engineering on May 23, 2016; and by theAmerican National Standards Institute on June 1, 2016.This addendum was approved by a
2、Standing Standard Project Committee (SSPC) for which the Standards Committee has estab-lished a documented program for regular publication of addenda or revisions, including procedures for timely, documented, con-sensus action on requests for change to any part of the standard. The change submittal
3、form, instructions, and deadlines may beobtained in electronic form from the ASHRAE website (www.ashrae.org) or in paper form from the Senior Manager of Standards. The latest edition of an ASHRAE Standard may be purchased on the ASHRAE website (www.ashrae.org) or from ASHRAE Cus-tomer Service, 1791
4、Tullie Circle, NE, Atlanta, GA 30329-2305. E-mail: ordersashrae.org. Fax: 678-539-2129. Telephone: 404-636-8400 (worldwide), or toll free 1-800-527-4723 (for orders in US and Canada). For reprint permission, go towww.ashrae.org/permissions. 2016 ASHRAE ISSN 1041-2336ASHRAE is a registered trademark
5、of the American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.ANSI is a registered trademark of the American National Standards Institute.SPECIAL NOTEThis American National Standard (ANS) is a national voluntary consensus Standard developed under the auspices of ASHRAE. Conse
6、nsus is definedby the American National Standards Institute (ANSI), of which ASHRAE is a member and which has approved this Standard as an ANS, as“substantial agreement reached by directly and materially affected interest categories. This signifies the concurrence of more than a simple majority,but
7、not necessarily unanimity. Consensus requires that all views and objections be considered, and that an effort be made toward their resolution.”Compliance with this Standard is voluntary until and unless a legal jurisdiction makes compliance mandatory through legislation. ASHRAE obtains consensus thr
8、ough participation of its national and international members, associated societies, and public review.ASHRAE Standards are prepared by a Project Committee appointed specifically for the purpose of writing the Standard. The ProjectCommittee Chair and Vice-Chair must be members of ASHRAE; while other
9、committee members may or may not be ASHRAE members, allmust be technically qualified in the subject area of the Standard. Every effort is made to balance the concerned interests on all Project Committees. The Senior Manager of Standards of ASHRAE should be contacted fora. interpretation of the conte
10、nts of this Standard,b. participation in the next review of the Standard,c. offering constructive criticism for improving the Standard, ord. permission to reprint portions of the Standard.DISCLAIMERASHRAE uses its best efforts to promulgate Standards and Guidelines for the benefit of the public in l
11、ight of available information and acceptedindustry practices. However, ASHRAE does not guarantee, certify, or assure the safety or performance of any products, components, or systemstested, installed, or operated in accordance with ASHRAEs Standards or Guidelines or that any tests conducted under it
12、s Standards or Guidelineswill be nonhazardous or free from risk.ASHRAE INDUSTRIAL ADVERTISING POLICY ON STANDARDSASHRAE Standards and Guidelines are established to assist industry and the public by offering a uniform method of testing for rating purposes, bysuggesting safe practices in designing and
13、 installing equipment, by providing proper definitions of this equipment, and by providing other informationthat may serve to guide the industry. The creation of ASHRAE Standards and Guidelines is determined by the need for them, and conformanceto them is completely voluntary.In referring to this St
14、andard or Guideline and in marking of equipment and in advertising, no claim shall be made, either stated or implied,that the product has been approved by ASHRAE.ASHRAE Standing Standard Project Committee 170Cognizant TC: 9.6, Healthcare FacilitiesSPLS Liaison: John F. DunlapChris P. Rousseau*, Chai
15、r Robert N. Heinlein, Jr. Russell N. Olmsted*Michael P. Sheerin*, Vice-Chair Richard D. Hermans* Heather L. Platt*Jonathan J. Flannery*, Secretary Nolan Hosking* Kevin A. ScarlettJohn M. Dombrowski Michael R. Keen Erica StewartDouglas S. Erickson* Peter H. Langowski* Andrew J. StreifelJeremy P. Faub
16、er Farhad Memarzadeh* Gordon P. Sharp*Steven D. Friedman Richard D. Moeller*James (Skip) Gregory* Paul T. Ninomura* Denotes members of voting status when the document was approved for publicationASHRAE STANDARDS COMMITTEE 20152016Douglass T. Reindl, Chair Steven J. Emmerich Heather L. PlattRita M. H
17、arrold, Vice-Chair Julie M. Ferguson David RobinJames D. Aswegan Walter T. Grondzik Peter SimmondsNiels Bidstrup Roger L. Hedrick Dennis A. StankeDonald M. Brundage Srinivas Katipamula Wayne H. Stoppelmoor, Jr.John A. Clark Rick A. Larson Jack H. ZarourWaller S. Clements Lawrence C. Markel Julia A.
18、Keen, BOD ExOJohn F. Dunlap Arsen K. Melikov James K. Vallort, COJames W. Earley, Jr. Mark P. ModeraKeith I. Emerson Cyrus H. NasseriStephanie C. Reiniche, Senior Manager of Standards ASHRAE (www.ashrae.org). For personal use only. Additional reproduction, distribution, or transmission in either pri
19、nt or digital form is not permitted without ASHRAEs prior written permission.ANSI/ASHRAE/ASHE Addendum h to ANSI/ASHRAE/ASHE Standard 170-2013 1(This foreword is not part of this standard. It is merely informative and does not contain requirements necessary for conformance to the standard. It has no
20、t been pro-cessed according to the ANSI requirements for a standard and may contain material that has not been subject to public review ora consensus process. Unresolvedobjectors on informative material are offered the right to appeal at ASHRAE or ANSI.) FOREWORD Currently in the industry there is a
21、 discrepancy between ASHRAE standards and AAMI standards in several requirements for environmental conditions in areas of the Sterile Pro-cessing Department (SPD). ASHRAE standards guide the design of these areas, while AAMI standards guide their operation. Therefore, some amount of agreement is req
22、uiredbetween the two.In April of 2015, representatives of ASHRAE, AAMI, FGI, AORN, ASHE, and APIC met to discuss these issues. Addendum h representsthis groups recommendations forspace temperature in several spaces. Additionally, a note has been added to the standard referring users to the correspon
23、ding AAMI document, which includes additional require-ments to consider.Note: In this addendum, changes to the current standard are indicated in the text by underlining (for additions) and strikethrough (for deletions) unless the instructions specif-ically mention some other means of indicating the
24、changes. 9.NORMATIVEREFERENCES13ANSI/AAMI Standard ST79-2013, Comprehensive guide to steam sterilization and sterility assurance in health care facilities. Association for the Advancement of MedicalInstrumentation, Arlington, VA.AddendumhtoStandard170-2013Revise Table 7.1 as shown. The remainder of
25、Table 7.1 is unchanged.TABLE7.1DesignParametersFunction of SpacePressure Relationship to Adjacent Areas (n)Minimum Outdoor achMinimum Total achAll Room Air Exhausted Directly to Outdoors (j)Air Recirculated by Means of Room Units (a)Design Relative Humidity (k), %Design Temperature (l), F/C . . . CE
26、NTRAL MEDICAL AND SURGICAL SUPPLYSTERILE PROCESSING DEPARTMENTzSoiled or dDecontamination room Negative26YesNoNR7278/22266073/16-23Clean workroom Positive24NRNomax 607278/22266873/20-23Sterile storage roomPositive24NRNRmax 607278/2226max 75/24 . . . Notes for Table 7.1: . . . z.See AAMI Standard ST7
27、913for additional information for these spaces.Add the following references to Section 9. The remainder of Section 9 is unchanged. ASHRAE (www.ashrae.org). For personal use only. Additional reproduction, distribution, or transmission in either print or digital form is not permitted without ASHRAEs p
28、rior written permission. ASHRAE (www.ashrae.org). For personal use only. Additional reproduction, distribution, or transmission in either print or digital form is not permitted without ASHRAEs prior written permission.POLICY STATEMENT DEFINING ASHRAES CONCERNFOR THE ENVIRONMENTAL IMPACT OF ITS ACTIV
29、ITIESASHRAE is concerned with the impact of its members activities on both the indoor and outdoor environment.ASHRAEs members will strive to minimize any possible deleterious effect on the indoor and outdoor environment ofthe systems and components in their responsibility while maximizing the benefi
30、cial effects these systems provide,consistent with accepted Standards and the practical state of the art.ASHRAEs short-range goal is to ensure that the systems and components within its scope do not impact theindoor and outdoor environment to a greater extent than specified by the Standards and Guid
31、elines as established byitself and other responsible bodies.As an ongoing goal, ASHRAE will, through its Standards Committee and extensive Technical Committee structure,continue to generate up-to-date Standards and Guidelines where appropriate and adopt, recommend, and promotethose new and revised S
32、tandards developed by other responsible organizations.Through its Handbook, appropriate chapters will contain up-to-date Standards and design considerations as thematerial is systematically revised.ASHRAE will take the lead with respect to dissemination of environmental information of its primary in
33、terest andwill seek out and disseminate information from other responsible organizations that is pertinent, as guides to updatingStandards and Guidelines.The effects of the design and selection of equipment and systems will be considered within the scope of thesystems intended use and expected misus
34、e. The disposal of hazardous materials, if any, will also be considered.ASHRAEs primary concern for environmental impact will be at the site where equipment within ASHRAEs scopeoperates. However, energy source selection and the possible environmental impact due to the energy source andenergy transpo
35、rtation will be considered where possible. Recommendations concerning energy source selectionshould be made by its members. ASHRAE (www.ashrae.org). For personal use only. Additional reproduction, distribution, or transmission in either print or digital form is not permitted without ASHRAEs prior wr
36、itten permission.ASHRAE 1791 Tullie Circle NE Atlanta, GA 30329 www.ashrae.org About ASHRAEASHRAE, founded in 1894, is a global society advancing human well-being through sustainable technology for thebuilt environment. The Society and its members focus on building systems, energy efficiency, indoor
37、 air quality,refrigeration, and sustainability. Through research, Standards writing, publishing, certification and continuingeducation, ASHRAE shapes tomorrows built environment today. For more information or to become a member of ASHRAE, visit www.ashrae.org.To stay current with this and other ASHR
38、AE Standards and Guidelines, visit www.ashrae.org/standards.Visit the ASHRAE BookstoreASHRAE offers its Standards and Guidelines in print, as immediately downloadable PDFs, on CD-ROM, and viaASHRAE Digital Collections, which provides online access with automatic updates as well as historical version
39、s ofpublications. Selected Standards and Guidelines are also offered in redline versions that indicate the changes madebetween the active Standard or Guideline and its previous version. For more information, visit the Standards andGuidelines section of the ASHRAE Bookstore at www.ashrae.org/bookstor
40、e.IMPORTANT NOTICES ABOUT THIS STANDARDTo ensure that you have all of the approved addenda, errata, and interpretations for thisStandard, visit www.ashrae.org/standards to download them free of charge.Addenda, errata, and interpretations for ASHRAE Standards and Guidelines are no longerdistributed with copies of the Standards and Guidelines. ASHRAE provides these addenda,errata, and interpretations only in electronic form to promote more sustainable use ofresources.6/16
