1、ASME B18.30.1M-2000OPEN-END BLIND RIVETS WITH BREAK MANDRELS (METRIC SERIES)A N A M E R I C A N N A T I O N A L S T A N D A R DB18.30.1M-2000 5/10/00 2:47 PM Page 1Intentionally left blank A N A M E R I C A N N A T I O N A L S T A N D A R DOPEN-END BLIND RIVETSWITH BREAK MANDRELS(METRIC SERIES)ASME
2、B18.30.1M-2000B18.30.1M-2000 5/10/00 2:48 PM Page 3p. 1 05-25-00 12:19:20 Unit: ucp Textfile: b18301$cpe p. 1Date of Issuance: June 30, 2000This Standard will be revised when the Society approves the issuance ofa new edition. There will be no addenda or written interpretations of therequirements of
3、this Standard issued to this edition.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria forAmerican National Standards. The Standards Committee that approved the code or standardwas
4、balanced to assure that individuals from competent and concerned interests have had anopportunity to participate. The proposed code or standard was made available for public reviewand comment that provides an opportunity for additional public input from industry, academia,regulatory agencies, and th
5、e public-at-large.ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted inconnection with any items mentioned in this document, and does not undertake to insure a
6、nyoneutilizing a standard against liability for infringement of any applicable letters patent, nor assumeany such liability. Users of a code or standard are expressly advised that determination of thevalidity of any such patent rights, and the risk of infringement of such rights, is entirely theirow
7、n responsibility.Participation by federal agency representative(s) or person(s) affiliated with industry is not tobe interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued inaccordance with the est
8、ablished ASME procedures and policies, which precludes the issuanceof interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical Engineer
9、sThree Park Avenue, New York, NY 10016-5990Copyright 2000 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll Rights ReservedPrinted in U.S.A.p. 3 05-25-00 12:19:36 Unit: ufw Textfile: b18301$fw p. 3FOREWORDIn 1994, ASME established the B18.30 subcommittee. This subcommittee was initiallyformed to dev
10、elop U.S. standards for blind rivets. After the first meeting however, it wasrecommended that the subcommittee should develop standards for all blind fasteners.The first endeavor by this subcommittee was to create U.S. standards for metric blindrivets, followed by U.S. standards for inch blind rivet
11、s. It was further recommended thatthe U.S. committee consider input based on the International Standards Organization (ISO)and the Industrial Fastener Institute (IFI). The latter organization was the first to establishwell-documented, dimensional and mechanical properties for blind rivets. Therefore
12、, muchof the data in the IFI standards was used to prepare this standard.ASME B18.30.1M-2000 was approved by the American National Standards Institute(ANSI) on February 29, 2000.iiiIntentionally left blank p. 5 05-25-00 12:19:54 Unit: ucr Textfile: b18301$cr p. 5ASME B18 STANDARDS COMMITTEEStandardi
13、zation of Bolts, Nuts, Rivets, Screws,Washers, and Similar Fasteners(The following is the roster of the Committee at the time of approval of this Standard.)OFFICERSD. A. Clever, ChairR. D. Strong, Vice ChairS. W. Vass, Vice ChairR. L. Crane, SecretaryCOMMITTEE PERSONNELJ. Altman, Rotor Clip Co.J. H.
14、 Slass, Alternate, Rotor Clip Co.J. B. Belford, Lawson Products, Inc.J. A. Buda, SPS TechnologiesR. M. Byrne, Trade Association Management, Inc.D. A. Clever, Deere and Co.A. P. Cockman, Ford Motor Co.T. Collier, Cam-Tech Industries, Inc.R. L. Crane, The American Society of Mechanical EngineersA. C.
15、DiCola, Wrought Washer Co.A. Dinh, Defense Industrial Supply CenterW. D. Downing, ConsultantB. A. Dusina, Federal Screw WorksD. S. George, Ford Motor Co.D. L. Drobnich, Alternate, Ford Mortor Co.J. Greenslade, Greenslade and Co.B. Hasiuk, Defense Industrial Supply CenterA. Herskovitz, U.S. Army ARDE
16、CA. C. Hood, ACH TechnologiesJ. Hubbard, Rockford Fastener, Inc.D. F. Kattler, ConsultantF. W. Kern, The Society of Automotive EngineersJ. F. Koehl, Spirol International Corp.W. H. Kopke, ITW Shakeproof Assembly Co.J. G. Langenstein, ConsultantM. Levinson, ITW Shakeproof Assembly Co.L. L. Lord, Cate
17、rpillar, Inc.R. L. Tennis, Alternate, Caterpillar, Inc.D. B. Mantas, GE EmpisA. D. McCrindle, Genfast Manufacturing Co.K. E. McCullough, ConsultantR. B. Meade, Camcar TextronM. D. Prasad, General Motors Corp.S. Savoji, ITW MedalistW. Schevey, BGM Fastener Co., Inc.R. D. Strong, General Motors Corp.J
18、. F. Sullivan, National Fasteners Distribution AssociationS. W. Vass, Industrial Fasteners Institutevp. 6 05-25-00 12:19:54 Unit: ucr Textfile: b18301$cr p. 6C. B. Wackrow, MNP Corp.R. G. Weber, Fairfield UniversityW. K. Wilcox, Naval Sea Systems CommandC. J. Wilson, Industrial Fasteners InstituteD.
19、 R. Akers, Alternate, Industrial Fasteners InstituteR. B. Wright, Wright Tool Co.J. G. Zeratsky, National Rivet however, they should not contain proprietary names orinformation.Requests that are not in this format will be rewritten in this format by the Committeeprior to being answered, which may in
20、advertently change the intent of the original request.ASME procedures provide for reconsideration of any interpretation when or if additionalinformation that might affect an interpretation is available. Further, persons aggrieved byan interpretation may appeal to the cognizant ASME Committee or Subc
21、ommittee. ASMEdoes not “approve,” “certify,” “rate,” or “endorse” any item, construction, proprietary device,or activity.Attending Committee Meetings. The B18 Main Committee regularly holds meetings, whichare open to the public. Persons wishing to attend any meeting should contact the Secretaryof th
22、e B18 Main Committee.viiIntentionally left blank p. 9 05-25-00 12:21:14 Unit: uct Textfile: b18301$ct p. 9CONTENTSForeword iiiCommittee Roster vCommittee Correspondence vii1 Introductory Notes . 11.1 1Scope .1.2 1Dimensions 1.3 1Options .1.4 1Terminology .1.5 1Referenced Standards 1.6 1Comparison wi
23、th ISO Standards 2 General Data 12.1 1Description 2.2 1Styles .3 Rivet Dimensions 24 Finish 25 Application Data 25.1 2Protruding Head Styles 5.2 2Countersunk Head Styles .6 Grades and Materials . 27 Mechanical and Performance Requirements . 27.1 2Shear Strength 7.2 2Tensile Strength .7.3 2Mandrel Br
24、eak Load .8 Designation 29 Workmanship 210 Quality Assurance Provisions . 3Tables1 Dimensions of Regular and Large Protruding Head Style Break Mandrel BlindRivets . 42 Dimensions of 100 deg and 120 deg Countersunk Head Style Break Mandrel BlindRivets . 5ixp. 10 05-25-00 12:21:14 Unit: uct Textfile:
25、b18301$ct p. 103 Application Data for Protruding Head Style Break Mandrel Blind Rivets 64 Application Data for Countersunk Head Style Break Mandrel Blind Rivets 75 Grades of Break Mandrel Blind Rivets 86 Ultimate Shear and Tensile Strengths of Break Mandrel Blind Rivets . 97 Mandrel Break Loads of B
26、reak Mandrel Blind Rivets (Newtons) . 9xp. 1 08-07-00 13:18:41 Unit: u1 Textfile: b183010001 p. 1ASME B18.30.1M-2000OPEN-END BLIND RIVETS WITH BREAK MANDRELS (METRIC SERIES)1 INTRODUCTORY NOTES ASTM A638/A638M, Standard Specification for Precip-itation Hardening Iron Base Superalloy Bars, Forg-1.1 S
27、copeings, and Forging Stock for High-Temperature ServiceASTM A853, Standard Specification for Steel Wire,This Standard establishes the dimensional, mechani-Carbon, for General Usecal, and performance requirements of open-end blindASTM B127, Standard Specification for Nickel-Copperrivets with break m
28、andrels (metric series).Alloy (UNS N04400) Plate, Sheet, and StripASTM B152M, Standard Specification for Copper1.2 DimensionsSheet, Strip, Plate, and Rolled Bar (Metric)All dimensions in this Standard are in millimetersASTM B164, Standard Specification for Nickel-Copper(mm), unless stated otherwise.
29、Alloy Rod, Bar, and WireASTM B211M, Standard Specification for Aluminum1.3 Optionsand Aluminum-Alloy Bar, Rod, and Wire (Metric)Options, if specified, shall be at the discretion ofASTM B221M, Standard Specification for Aluminumthe supplier, unless otherwise agreed upon by theand Aluminum-Alloy Extru
30、ded Bars, Rods, Wire,supplier and purchaser.Profiles, and Tubes (Metric)ASTM B316/B316M, Standard Specification for Alumi-1.4 Terminologynum and Aluminum-Alloy Rivet and Cold-HeadingWire and RodsFor definitions of terms relating to fasteners or compo-nent features thereof used in this Standard, refe
31、r toPublisher: American Society for Testing and MaterialsASME B18.12.(ASTM), 100 Bar Harbor Drive, West Conshohocken,PA 19428-29591.5 Referenced StandardsUnless otherwise specified, the reference shall be to1.6 Comparison with ISO Standardsthe most recent edition at the time of order placement.Blind
32、 rivet standards have not been issued by ISO.ASME B18.12, Glossary of Terms for MechanicalFastenersASME B18.18.1M, Inspection and Quality Assurancefor General Purpose Fasteners2 GENERAL DATAASME B18.24.3, Part Identifying Number (PIN) CodeSystem Standard for B182.1 DescriptionASME B18.30.2M, Mechani
33、cal Testing of Blind RivetsBreak mandrel blind rivets are pull mandrel type(under development)blind rivets where, during the setting operation, thePublisher: American Society of Mechanical Engineersmandrel is pulled into or against the rivet body and(ASME International), Three Park Avenue, Newbreaks
34、 at or near the junction of the mandrel shankYork, NY 10016; ASME Order Department: 22 Lawand its upset end.Drive, Box 2300, Fairfield, NJ 07007-2300ASTM A167, Standard Specification for Stainless and2.2 StylesHeat Resisting Chromium-Nickel Steel Plate, Sheet,and Strip2.2.1 Protruding Head. A protru
35、ding head blindASTM A493, Standard Specification for Stainless Steelrivet has a rivet head that projects beyond the surfaceWire and Wire Rods for Cold Heading and Coldof the assembly after setting. The two styles of protrud-Forginging heads included in this Standard are regular head,ASTM A580/A580M,
36、 Standard Specification for Stain-less Steel Wire style 1; and large head, style 2 (see Table 1).1p. 2 08-07-00 13:18:41 Unit: u1 Textfile: b183010001 p. 2OPEN-END BLIND RIVETS WITH BREAK MANDRELS(METRIC SERIES)ASME B18.30.1M-20002.2.2 Countersunk Head. A countersunk head 7 MECHANICAL AND PERFORMANC
37、EREQUIREMENTSblind rivet is one, which after setting, has a head thatis essentially flush with the surface of the fastenedcomponent. The two styles included in this Standard 7.1 Shear Strengthare 100 deg countersunk head, style 3; and 120 degRivets, except Grade 20, shall have ultimate shearcounters
38、unk head, style 4 (see Table 2).strengths not less than the minimum ultimate shearstrengths specified for the applicable size and gradegiven in Table 6, when tested in accordance withASME B18.30.2M (when issued).3 RIVET DIMENSIONSProtruding head break mandrel blind rivets style 17.2 Tensile Strength
39、and style 2 shall conform to the dimensions indicatedRivets, except Grade 20, shall have ultimate tensilein Table 1. Countersunk head style break mandrel blindstrengths not less than the minimum ultimate tensilerivets style 3 and style 4 shall conform to the dimensionsstrengths specified for the app
40、licable size and gradeindicated in Table 2.given in Table 6, when tested in accodance with ASMEB18.30.2M (when issued).7.3 Mandrel Break Load4 FINISHWhile the rivet is being set, the axially applied loadRivets shall have a plain finish (unplated or uncoated)necessary to break the mandrel shall be wi
41、thin theunless otherwise specified. Finishes and coatings forlimits specified for the applicable rivet size and gradespecial requirements, such as military usage, should bein Table 7, when tested in accordance with ASMEspecified through the appropriate ASTM standards withB18.30.2M (when issued).the
42、agreement of the purchaser.8 DESIGNATION5 APPLICATION DATA Head Style Codes:Recommendations on the selection and applicationP1 p protruding head style 1of protruding or countersunk head break mandrel blindrivets are given in Tables 3 and 4 respectively. P2 p protruding head style 2C3 p countersunk h
43、ead style 35.1 Protruding Head StylesC4 p countersunk head style 4Recommended drill size, hole size, grip range, andmaximum rivet body length are given in Table 3.Head Style Nominal Rivet Size Max. Rivet Length, L Material Grade5.2 Countersunk Head StylesEXAMPLE: P1 4.8 17.8 11Recommended drill size
44、, hole size, grip range, andThis example shows a 4.8 mm diameter rivet withmaximum rivet body length are given in Table 4.a protruding head of style 1 (Table 1), a maximumlength of 17.8 mm (Table 3), and an aluminum alloybody with aluminum alloy mandrel (Table 5).For a recommended part indentifying
45、numbering sys-6 GRADES AND MATERIALStem (PIN), see ASME B18.24.3.The material combinations of break mandrel blindrivets are designated as grades, with each material9 WORKMANSHIPcombination of rivet body material and mandrel materi-als as given in Table 5. Grade 20 rivets are not subject Rivets shall
46、 be free of burrs, loose scale, seams,notches, sharp edges and corners, and other irregularitiesto either shear or tensile testing.2p. 3 08-07-00 13:18:41 Unit: u1 Textfile: b183010001 p. 3OPEN-END BLIND RIVETS WITH BREAK MANDRELS(METRIC SERIES) ASME B18.30.1M-2000or detrimental defects that could a
47、ffect their service-ability.10 QUALITY ASSURANCE PROVISIONSUnless otherwise specified by the purchaser, accept-ability of rivets shall be based on conformance withthe requirements specified in ASME B18.18.1M.3p. 4 08-07-00 13:18:41 Unit: u1 Textfile: b18301$u1 p. 4OPEN-END BLIND RIVETS WITH BREAK MA
48、NDRELS(METRIC SERIES)ASME B18.30.1M-2000RLFDHWEPPoint style optional 1.6 Max.TABLE1DIMENSIONSOFREGULARANDLARGEPROTRUDINGHEADSTYLEBREAKMANDRELBLINDRIVETSStyle1:Style2:RegularHeadLargeHeadMax.NominalMin.Max.BodyHeadHeadHeadHeadNominalRadiusMandrelMandrelBlindSideDiameter,DDiameter,HHeight,EDiameter,HH
49、eight,ERivetofFillet,Diameter,Protrusion,Protrusion,SizeMax.Min.Max.Min.Max.Max.Min.Max.RNote(1)WPFNote(2)2.42.442.295.034.520.817.446.831.020.41.4525L+2.53.23.253.106.656.051.029.919.141.650.51.9325L+3.04.04.043.898.337.521.2712.4011.381.900.52.4125L+3.54.84.854.6510.019.041.5216.5115.242.340.72.9025L+4.06.36.486.2513.3312.072.0319.8118.292.720.83.8425L+4.5GENERALNOTES:(a)Alldimensionsareinmillimeters(mm).(b)Forapplicationdata,seeTable3.NOTES: (1)Thejunctionofheadandshankshallhaveafilletwithamaximumradiusasshown.ForGrades40,50,51,and52rivets,themaximumfilletradiusfor4
