1、Designation: A1025/A1025M 10Standard Specification forFerroalloys and Other Alloying Materials, GeneralRequirements1This standard is issued under the fixed designation A1025/A1025M; the number immediately following the designation indicates theyear of original adoption or, in the case of revision, t
2、he year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers a group of common require-ments that, unless otherwise specified in an individua
3、l speci-fication, shall apply to ferroalloys and other alloying materialsunder each of the following ASTM specifications:Title of Specification ASTM DesignationFerromanganese A99Ferrosilicon A100Ferrochromium A101Ferrovanadium A102Ferromolybdenum A132Molybdenum Oxide Products A146Ferroboron A323Ferr
4、otitanium A324Chromium Metal A481Ferrochrome-Silicon A482Silicomanganese A483Calcium-Silicon Alloys A495Ferrocolumbium A550Electrolytic Manganese Metal A601Nickel Oxide Sinter A636Ferromanganese Silicon A701Titanium Scrap for Use in Deoxidation and Alloying of Steel A845Aluminum Scrap for Use in Deo
5、xidation and Alloying of Steel A846Silicon Metal A9221.2 This specification also covers a group of supplementaryrequirements which may be applied to the above specificationsas indicated therein. These are provided for use when addi-tional testing or inspection is desired and apply only whenspecified
6、 individually by the purchaser in the order.1.3 In case of conflict between the requirements of theindividual specification and this general specification, theformer shall prevail.1.4 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard. Thevalues s
7、tated in each system may not be exact equivalents;therefore, each system shall be used independently of the other.Combining values from the two systems may result in non-conformance with the standard.1.4.1 This specification is expressed in both inch-poundunits and in SI units (Within the text, the
8、SI units are shown inbrackets); however, unless the purchase order or contractspecifies the applicable M specification designation (SI units),the inch-pound units shall apply.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibi
9、lity of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory requirements prior to use.2. Referenced Documents2.1 ASTM Standards:2A99 Specification for FerromanganeseA100 Specification for FerrosiliconA101 Specification for Fe
10、rrochromiumA102 Specification for FerrovanadiumA132 Specification for FerromolybdenumA146 Specification for Molybdenum Oxide ProductsA323 Specification for FerroboronA324 Specification for FerrotitaniumA481 Specification for Chromium MetalA482 Specification for Ferrochrome-SiliconA483 Specification
11、for SilicomanganeseA495 Specification for Calcium-Silicon AlloysA550 Specification for FerrocolumbiumA601 Specification for Electrolytic Manganese MetalA610 Test Methods for Sampling and Testing Ferroalloysfor Determination of SizeA636 Specification for Nickel Oxide SinterA701 Specification for Ferr
12、omanganese-SiliconA845 Specification for Titanium Scrap for Use in Deoxida-tion and Alloying of Steel3A846 Specification for Aluminum Scrap for Use in Deoxi-dation and Alloying of Steel3A922 Specification for Silicon MetalE29 Practice for Using Significant Digits in Test Data toDetermine Conformance
13、 with SpecificationsE32 Practices for Sampling Ferroalloys and Steel Additives1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.18 on Castings.Current edition approved Oct. 1, 2010. Publ
14、ished November 2010. Originallyapproved in 2002. Last previous edition approved in 2010 as A1025 - 05 (2010).DOI: 10.1520/A1025_A1025M-10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume
15、information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C
16、700, West Conshohocken, PA 19428-2959, United States.for Determination of Chemical Composition3. Ordering Information3.1 Orders for material should include the following asrequired, to describe the material adequately:3.1.1 ASTM designation and year of issue,3.1.2 Grade of material,3.1.3 Size of mat
17、erial,3.1.4 Quantity,3.1.5 Packaging requirements, and3.1.6 Supplementary requirements desired, including thestandards of acceptance.4. Chemical Analysis4.1 The chemical analysis method shall be agreed upon bythe purchaser and supplier.4.2 The manufacturer shall furnish a certificate referencingthe
18、chemical analysis and appropriate supplementary require-ments in the material specification.4.3 For purposes of determining conformance with thisspecification, the reported analysis shall be rounded to thenearest unit in the last right-hand place of figures, used inexpressing the limiting value, in
19、accordance with the roundingmethod of Practice E29.5. Sampling5.1 Unless otherwise specified, the material shall besampled for determination of chemical composition in accor-dance with Practices E32 and for determination of size inaccordance with Test Methods A610.5.2 In the case of a discrepancy, P
20、ractices E32 or TestMethods A610, as applicable, shall be used for referee.6. Inspection6.1 The manufacturer shall afford the inspector representingthe purchaser all reasonable facilities, without charge, to satisfythe purchaser that the material is being furnished in accordancewith the material spe
21、cification.7. Rejection7.1 Any rejections based on tests made in accordance withthe material specification shall be reported to the manufacturerwithin 45 days from receipt of material by the purchaser.8. Certification8.1 The manufacturers certification shall be furnished tothe purchaser at the time
22、of shipment stating that the materialwas manufactured, sampled, tested, and inspected in accor-dance with the material specification and was found to meet therequirements.9. Packaging and Package Marking9.1 Each lot/shipment shall be identified with appropriateidentification showing the material, th
23、e ASTM designation, thesize, the lot number, and name brand or trademark.9.2 When the shipment is made in containers, each shall bemarked on the container or on a label or tag attached to thecontainer.10. Keywords10.1 alloying materials; ferroalloy; general requirementsSUPPLEMENTARY REQUIREMENTSThe
24、following standardized supplementary requirements are for use when desired by the purchaserand when allowed by and listed in the individual specifications. They shall not apply unless specifiedin order, in which event the specified tests shall be made by the manufacturer before shipping.S1. Suppleme
25、ntary Chemical RequirementsS1.1 Restrictions on the chemical requirements shall beagreed upon by the purchaser and supplier.S2. SizeS2.1 Screened products shall conform to the sizes given inTable S2.1.S2.2 The sizes listed in Table S2.1 are typical as shippedfrom the manufacturers plant. The size an
26、d friability of theproduct shall be agreed upon by the purchaser and supplier.NOTE S1Ferroalloys exhibit varying degrees of friability; therefore,some attrition may be expected in transit and handling. A quantitative testis not available for rating friability of ferroalloys. A code system has beende
27、veloped for this purpose, and a number rating for each product type isgiven.A1025/A1025M 102APPENDIXES(Nonmandatory Information)X1. APPLICABLE SIEVE DESIGNATIONSX1.1TABLE S2.1 Requirements for Screened ProductsANominalSize, in. mmStandard OrderedSize, in.Maximum Allowable Oversize Maximum Allowable
28、UndersizeFriability RatingCode No.BSize in. mm Percent Size in. mm PercentLump to Crushed Sizes:6 150 8 200 by 4 100 to 10 250 10 % through 4 100 10 % 1-65 125 8 200 by 2 50 to 10 250 10 % through 2 50 10 % 1-64 100 6 150 by 2 50 to 8 200 10 % through 2 50 10 % 1-6312 90 5 125 by 2 50 to 7 175 10 %
29、through 2 50 10 % 1-63 (A) 75 5 125 by 1 25 to 7 175 10 % through 1 25 10 % 1-63 (B) 75 4 100 by 2 50 to 6 150 10 % through 2 50 10 % 1-6212 65 4 100 by 1 25 to 6 150 10 % through 1 25 10 % 1-6214 60 4 100 by12 15 to 5 125 10 % through12 15 10 % 1-62 50 3 75 by 1 25 to 4 100 10 % through 1 25 10 % 1
30、-6112 40 3 75 by12 15 to 4 100 10 % through12 15 10 % 1-6114 30 2 50 by12 15 to 3 75 10 % through12 15 10 % 1-6118 30 2 50 by14 5 to 3 75 10 % through14 5 10 % 1-6Small Crushed Sizes by Down:2 50 4 100 by D to 5 125 10 % through12 15 15 % 1-6112 40 3 75 by D to 4 100 10 % through18 5 15 % 1-61 25 2
31、50 by D to 3 75 10 % through18 5 15 % 1-4to 3 75 8 % through No. 8 20 % 5,612 15 1 25 by D to 112 40 10 % through No. 16 15 % 1-4to 112 40 8 % through No. 20 15 % 5,612 15 by D to34 20 10 % through No. 20 15 % 1-4to34 20 8 % through No. 70 20 % 5,6AFor screened products below12 in. 15 mm by down-cru
32、shed sizes, size tolerances should be agreed upon between manufacturer and purchaser.BSee Appendix X1 for description of rating code.TABLE X1.1 Sieve DesignationStandard Alternative250 mm 10 in.200 mm 8 in.175 mm 7 in.150 mm 6 in.125 mm 5 in.100 mm 4 in.75 mm 3 in.50 mm 2 in.25 mm 1 in.19 mm34 in.12
33、.5 mm12 in.6.3 mm14 in.3.1 mm18 in.2.36 mm No. 81.18 mm No. 16850 mANo. 20212 m No. 70A1000 m=1mm.A1025/A1025M 103X2. FRIABILITY RATINGS OF FERROALLOYSX2.1 Descriptions of material of each friability rating aregiven in Table X2.1.SUMMARY OF CHANGESCommitteeA01 has identified the location of selected
34、 changes to this standard since the last issue (A1025 05(2010) that may impact the use of this standard. (Approved Oct. 1, 2010.)(1) 1.4 added. (2) Table S2.1 revised.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin th
35、is standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must b
36、e reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theres
37、ponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, W
38、est Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission ri
39、ghts to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE X2.1 Friability Ratings of FerroalloysFriabilityCode No.Description1 Very tough materials that are susceptible to little, if any, breakageduring shipment or handling. (Example: low-carbon ferroch
40、rome)2 Some breakage of large pieces probable in shipping and handling.No appreciable fines produced from either lump or crushed sizes.(Example: chrome metal)3 Appreciable reduction in size of large pieces possible in shippingand handling. No appreciable production of fines in handling ofcrushed siz
41、es. (Example: ferrotitanium)4 Appreciable reduction in size of large pieces upon repeatedhandling. Some fines produced upon repeated handling ofcrushed sizes. (Example: standard ferromanganese)5 Appreciable reduction in size in repeated handling of large pieces.Appreciable fines may be produced in the handling of crushedsizes. (Example: 50 % ferrosilicon)6 This category represents the most friable alloys. (Example: calciumsilicon)A1025/A1025M 104
