1、Designation: A116 11 (Reapproved 2016)Standard Specification forMetallic-Coated, Steel-Woven Wire Fence Fabric1This standard is issued under the fixed designation A116; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of la
2、st revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This specification covers metallic
3、-coated steel fencefabric having a series of horizontal (line) wires, with vertical(stay) wires either wrapped around the line wire (hinge joint) orfixed with another separate wire to the line wire (continuousstay fixed knot joint), forming rectangular openings. The fencefabric is suitable for use i
4、n fences for farm field enclosure (tokeep domestic animals in or out), for wildlife and exotic animalcontrol, for highway or railroad right-of-way fencing (tocontrol access), and other similar uses.1.2 This specification covers fence fabric in various designs,tensile strength grades, and metallic co
5、ating types and grades.1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 The text of this specification references notes andfootnot
6、es which provide explanatory material. These notes andfootnotes (excluding those in tables and figures) shall not beconsidered as requirements of the specification.2. Referenced Documents2.1 ASTM Standards:2A90/A90M Test Method for Weight Mass of Coating onIron and Steel Articles with Zinc or Zinc-A
7、lloy CoatingsA370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA428/A428M Test Method for Weight Mass of Coating onAluminum-Coated Iron or Steel ArticlesA510 Specification for General Requirements for Wire Rodsand Coarse Round Wire, Carbon SteelA641/A641M Specification for Zin
8、cCoated (Galvanized)Carbon Steel WireA700 Guide for Packaging, Marking, and Loading Methodsfor Steel Products for ShipmentA809 Specification for Aluminum-Coated (Aluminized)Carbon Steel WireA856/A856M Specification for Zinc-5 % Aluminum-Mischmetal Alloy-Coated Carbon Steel WireA902 Terminology Relat
9、ing to Metallic Coated Steel Prod-ucts2.2 U.S. Federal Standard:Fed. Std. No. 123 Marking for Shipments (Civil Agencies)32.3 U.S. Military Standards:MIL-STD-129 Marking for Shipment and Storage3MIL-STD-163 Steel Mill Products, Preparation for Ship-ments and Storage33. Terminology3.1 DefinitionsFor d
10、efinitions of terms used in thisspecification, refer to Terminology A902.3.2 Definitions of Terms Specific to This Standard:3.2.1 continuous stay fixed knot joint, nhorizontal linewire and vertical stay wire joint made by fastening continuousstay wires to line wires by tying them together with a sep
11、aratepiece of knot wire at each joint.3.2.2 hinge joint, nhorizontal line wire and vertical staywire joint made by wrapping stay wire around line wires.3.2.3 intermediate wires, nline wires other than top andbottom wires.3.2.4 top and bottom wires, nline wires at the edge of thefence fabric (the top
12、 and bottom edges as erected).4. Ordering Information4.1 Orders for material under this specification shall includethe following information, as necessary to describe eachproduct ordered.1This specification is under the jurisdiction of ASTM Committee A05 onMetallic-Coated Iron and Steel Products and
13、 is the direct responsibility ofSubcommittee A05.12 on Wire Specifications.Current edition approved Nov. 1, 2016. Published November 2016. Originallyapproved in 1927. Last previous edition approved in 2011 as A116 - 11. DOI:10.1520/A0116-11R16.2For referenced ASTM standards, visit the ASTM website,
14、www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 1
15、9111-5098, http:/dodssp.daps.dla.mil.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.1.1 Name of material and joint style (woven steel fencefabric with hinge joint or continuous stay fixed knot joint);4.1.2 Quantity (number of rolls
16、);4.1.3 Design NumberNumber describing standard sizesand construction of the fabric as listed in Table 1;NOTE 1The design numbers are related to the characteristics of theconstruction of the fence fabric. The design number indicates the numberof line wires, approximate height, stay wire spacing, and
17、 size (gage) of theline and stay wires.4.1.4 Fabric LengthWhen length is not specified by theorder fabric is furnished to the standard length of 330 ft (101m);4.1.5 Tensile Strength GradeThe fabric is available instrength grades of 60, 125, and 175 (see Table 1);4.1.6 Metallic Coating Type;4.1.6.1 C
18、oating Type AMade from aluminum coatedwire.4.1.6.2 Coating Type ZMade from zinc coated wire.4.1.6.3 Coating Type ZAMade from Zn-5 % Al-miscmetal alloy (Zn-5Al-MM) coated wire.4.1.7 Metallic Coating Class (see Table 2);4.1.8 ASTM designation and year of issue, and4.1.9 Certification, or test report,
19、or both, if required (seeSection 10).NOTE 2A typical ordering description is as follows: Woven-steelfence fabric, hinge joint, 60 rolls, Design Number 1047-6-1212, rolllength 330 ft, Grade 60, Coating Type Z, Coating Class 3, to ASTMA116-_, with certification.4.2 All rolls of fence fabric accepted b
20、y the purchaser shallbe billed on the basis of the original length of the rolls beforesampling unless changed by contractual agreement.5. Material5.1 WireThe steel wire shall be coated prior to fabrication,to the coating class specified in the order, the coating weight(mass) conforming to the requir
21、ements of Table 2. Coated wireshall be produced to the following applicable specifications:5.1.1 Coating Type ASpecification A809;5.1.2 Coating Type ZSpecification A641/A641M;5.1.3 Coating Type ZASpecification A856/A856M.5.2 Coated Wire SizeCoated wire gage sizes shown inTable 1, Table 2, and Table
22、3 corresponds to steel wire gagesizes listed in Specification A510, within the tolerances statedin Section 7.6. General Requirements6.1 ConstructionThe sizes and constructions for fencefabric furnished under this specification shall be in accordancewith the requirements of Table 1 for the design num
23、berspecified in the order, within the tolerances stated in Section 7.Designs other than specified in the table can be manufacturedupon agreement between purchaser and producer. Each designcan be manufactured with hinge joint or continuous stay fixedknot joint.6.2 Horizontal WireHorizontal wires of a
24、ll woven fencingshall be furnished with tension curves, at least one tensioncurve per each 9 in. (229 mm) of horizontal (line) wire.6.3 SplicesSplicing of the individual line wires by meansof a wrap joint, mechanical fasteners, or an electric buttweld ispermitted. The maximum number of line wire spl
25、ices or jointsshall not exceed one-half of the number of line wires in any330 ft (101 m) (20 rod) roll of fabric. Such splices and jointsshall be made in a workman-like manner and welded jointsshall be coated with the corresponding Type A, Z, or ZA-coating material to provide corrosion protection eq
26、uivalent tothe type of coated wire being used.6.4 Stay WiresStay wires shall be uniformly spaced andsubstantially perpendicular to the line wires. Tie wire used forthe continuous stay fixed knot joint style fabric shall beminimum 13.5 gage and of the same coating type and class asstay wire.6.5 Fence
27、 Fabric LengthThe length of fence fabric in aroll shall be 330 ft (101 m) (20 rod). Fabric length other than330 ft can be manufactured upon agreement between purchaserand producer.6.6 Breaking StrengthThe breaking strength of line wiresshall conform to the requirements of Table 3 for the gradespecif
28、ied in the order. There is no strength requirement for thestay wires for hinge joint style fabric. For Grade 175 continu-ous stay fixed knot joint style fabric, stay wire minimum tensilestrength is 100 ksi (Grade 100).7. Permissible Variations in Dimensions7.1 Wire DiameterThe permissible variation
29、of the wire,from the nominal diameter shown in Table 3, shall be 60.005in. (60.127 mm). Determine the diameter using a micrometeror other suitable measuring instrument, based on the greatestand least measurement at the same cross-section, with mea-surement to the nearest 0.001 in. (0.025 mm). The av
30、erage ofthe two measurements shall be considered the diameter of thetest specimen.7.1.1 Out-of-RoundnessDue to the mechanics ofmanufacture, a certain amount of out-of-roundness is expectedon the stay wires of the finished fence fabric. No limits areplaced on out-of-roundness of the stay wires.7.2 Fa
31、bric HeightThe height of the woven wire fencefabric (center-to-center distance between top and bottom wires)shall not vary more than 1 in. (25 mm) from the specifiedheight shown in Table 1. The specified height of the fencefabric is based on the sum of the line wire spacings shown inFig. 1, Fig. 2,o
32、rFig. 3.7.3 Stay Wire SpacingThe spacing between individualpairs of stay wires, shall not vary from the nominal dimensionsmore than38 in. (10 mm) for 3 in. and 6 in. spacing and nomore than34 in. (19 mm) for 12 in. spacing product.7.4 Horizontal (Line) Wire SpacingThe spacing betweenhorizontal wires
33、 shall be as illustrated in Fig. 1, Fig. 2, and Fig.3. Alternative spacing to that illustrated in Fig. 1, Fig. 2, andFig. 3 is acceptable for given design number when agreed uponbetween purchaser and producer, providing that the totalnumber of line wires remains unchanged. The spacing betweenindivid
34、ual pairs of horizontal wires shall not vary from theaccepted nominal dimensions by more than38 in. (10 mm).A116 11 (2016)2TABLE 1 Design Numbers for Woven Wire Fence Fabric, Hinge Joint or Continuous Stay Fixed Knot JointNOTE 1Design combinations other than listed in the table can be manufactured u
35、pon purchasers request.NOTE 2Each design can be manufactured with hinge joint or continuous stay fixed knot joint.Design NumbersNumber ofHorizontal WiresNominal Fence Height,in. (cm)Spacing of StayWires, in. (cm)Size, Steel Wire GageIntermediate Lineand Stay WiresTop andBottom WiresNo. 9 Grade 60115
36、5-12-9 11 55 (140) 12 (30) 9 91047-12-9 10 47 (119) 12 (30) 9 9939-12-9 9 39 (99) 12 (30) 9 9832-12-9 8 32 (81) 12 (30) 9 9726-12-9 7 26 (66) 12 (30) 9 9949-12-9 9 49 (124) 12 (30) 9 9845-12-9 8 45 (114) 12 (30) 9 9635-12-9 6 35 (89) 12 (30) 9 91155-6-9 11 55 (140) 6 (15) 9 91047-6-9 10 47 (119) 6 (
37、15) 9 9726-6-9 7 26 (66) 6 (15) 9 9No. 11 Grade 601047-12-11 10 47 (119) 12 (30) 11 9939-12-11 9 39 (99) 12 (30) 11 9832-12-11 8 32 (81) 12 (30) 11 9726-12-11 7 26 (66) 12 (30) 11 9845-12-11 8 45 (114) 12 (30) 11 9635-12-11 6 35 (89) 12 (30) 11 91047-6-11 10 47 (119) 6 (15) 11 9939-6-11 9 39 (99) 6
38、(15) 11 9832-6-11 8 32 (81) 6 (15) 11 9726-6-11 7 26 (66) 6 (15) 11 9No. 1212 Grade 601047-12-1212 10 47 (119) 12 (30) 1212 10939-12-1212 9 39 (99) 12 (30) 1212 10832-12-1212 8 32 (81) 12 (30) 1212 10726-12-1212 7 26 (66) 12 (30) 1212 10845-12-1212 8 45 (114) 12 (30) 1212 10635-12-1212 6 35 (89) 12
39、(30) 1212 101047-6-1212 10 47 (119) 6 (15) 1212 10939-6-1212 9 39 (99) 6 (15) 1212 10832-6-1212 8 32 (81) 6 (15) 1212 10726-6-1212 7 26 (66) 6 (15) 1212 10No. 1412 Grade 60939-6-1412 9 39 (99) 6 (15) 1412 11832-6-1412 8 32 (81) 6 (15) 1412 11726-6-1412 7 26 (66) 6 (15) 1412 11No. 1212 Grade 1251047-
40、12-1212 10 47 (119) 12 (30) 1212 1012939-12-1212 9 39 (99) 12 (30) 1212 1012832-12-1212 8 32 (81) 12 (30) 1212 1012726-12-1212 7 26 (66) 12 (30) 1212 10121047-6-1212 10 47 (119) 6 (15) 1212 1012939-6-1212 9 39 (99) 6 (15) 1212 1012832-6-1212 8 32 (81) 6 (15) 1212 1012726-6-1212 7 26 (66) 6 (15) 1212
41、 1012No. 1212 Grade 1251478-6-1212 14 78 (198) 6 (15) 1212 1212No. 14 Grade 1251047-12-14 10 47 (119) 12 (30) 14 1212939-12-14 9 39 (99) 12 (30) 14 1212832-12-14 8 32 (81) 12 (30) 14 1212726-12-14 7 26 (66) 12 (30) 14 12121047-6-14 10 47 (119) 6 (15) 14 1212939-6-14 9 39 (99) 6 (15) 14 1212832-6-14
42、8 32 (81) 6 (15) 14 1212726-6-14 7 26 (66) 6 (15) 14 1212No. 1412 Grade 1251047-12-1412 10 47 (119) 12 (30) 1412 1212939-12-1412 9 39 (99) 12 (30) 1412 1212832-12-1412 8 32 (81) 12 (30) 1412 1212726-12-1412 7 26 (66) 12 (30) 1412 12121047-6-1412 10 47 (119) 6 (15) 1412 1212939-6-1412 9 39 (99) 6 (15
43、) 1412 1212832-6-1412 8 32 (81) 6 (15) 1412 1212726-6-1412 7 26 (66) 6 (15) 1412 1212No. 1212 Grade 175. For continuous stay fixed knot joint style fabric, stay wire minimum tensile strength is 100 ksi, ties wire diameter is minimum 13.5 GA1375-12-1212 13 75 (191) 12 (30) 1212 1212A116 11 (2016)3The
44、 tolerance of the line wires spacing shall not alter thetolerance on the overall height of the fence fabric.7.5 Fence Fabric LengthThe length of fence fabric in aroll shall be the specified length within a tolerance of 0 and+3 %.8. Sampling and Testing8.1 Unless otherwise specified in the purchase o
45、rder orcontract, the manufacturer is responsible for the performanceof all inspection and test requirements specified in this speci-fication. Except as otherwise specified in the purchase order orcontract, the manufacturer may use any suitable facilities forthe performance of the inspection and test
46、 requirements unlessdisapproved by the purchaser at the time the order is placed.The purchaser shall have the right to perform any of theinspection and tests set forth in this specification when suchinspections and tests are deemed necessary to assure that thematerial conforms to prescribed requirem
47、ents.TABLE 1 ContinuedDesign NumbersNumber ofHorizontal WiresNominal Fence Height,in. (cm)Spacing of StayWires, in. (cm)Size, Steel Wire GageIntermediate Lineand Stay WiresTop andBottom Wires1047-12-1212 10 47 (119) 12 (30) 1212 12122096-12-1212 20 96 (244) 12 (30) 1212 12121796-12-1212 17 96 (244)
48、12 (30) 1212 12121886-12-1212 18 86 (218) 12 (30) 1212 12121775-12-1212 17 75 (191) 12 (30) 1212 12121584-12-1212 15 84 (213) 12 (30) 1212 12121561-12-1212 15 61 (155) 12 (30) 1212 12121348-12-1212 13 48 (122) 12 (30) 1212 12121060-12-1212 10 60 (152) 12 (30) 1212 1212949-12-1212 9 49 (124) 12 (30)
49、1212 1212842-12-1212 8 42 (107) 12 (30) 1212 12121047-9-1212 10 47 (119) 9 (23) 1212 121223120-6-1212 23 120 (305) 6 (15) 1212 12122096-6-1212 20 96 (244) 6 (15) 1212 12121796-6-1212 17 96 (244) 6 (15) 1212 12121886-6-1212 18 86 (218) 6 (15) 1212 12121584-6-1212 15 84 (213) 6 (15) 1212 12121348-6-1212 13 48 (122) 6 (15) 1212 12121060-6-1212 10 60 (152) 6 (15) 1212 1212949-6-1212 9 49 (124
