1、Designation: A832/A832M 10 (Reapproved 2015)1Standard Specification forPressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Vanadium1This standard is issued under the fixed designation A832/A832M; the number immediately following the designation indicates the yearof original adoption or, in the
2、case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEEditorial information was added to Table 2 in September 2015.1. Scope1.1 This specification2cov
3、ers chromium-molybdenum-vanadium alloy steel plates intended primarily for the fabrica-tion of welded pressure vessels.1.2 The plates furnished under this specification are re-quired to be normalized-and-tempered. Specification A542/A542M includes coverage of the material in the quenched-and-tempere
4、d condition.1.3 The maximum thickness of plates furnished to thisspecification is limited only by the capacity of the compositionto meet the specified property requirements. However, themaximum thickness of plates normally furnished under thisspecification is 6 in. 150 mm.1.4 The material is intende
5、d to be suitable for fusionwelding. Welding technique is of fundamental importance andit is presupposed that welding procedures will be in accordancewith approved methods.1.5 This specification is expressed in both inch-pound unitsand in SI units. However, unless the order specifies theapplicable “M
6、” specification designation (SI units), the mate-rial shall be furnished to inch-pound units.1.6 The values stated in either inch-pound units or SI unitsare to be regarded separately as standard. Within the text, theSI units are shown in brackets. The values stated in eachsystem must be used indepen
7、dently of the other. Combiningvalues from the two systems may result in nonconformancewith the specification.2. Referenced Documents2.1 ASTM Standards:3A20/A20M Specification for General Requirements for SteelPlates for Pressure VesselsA370 Test Methods and Definitions for Mechanical Testingof Steel
8、 ProductsA435/A435M Specification for Straight-Beam UltrasonicExamination of Steel PlatesA542/A542M Specification for Pressure Vessel Plates,AlloySteel, Quenched-and-Tempered, Chromium-Molybdenum, and Chromium-Molybdenum-VanadiumA577/A577M Specification for Ultrasonic Angle-Beam Ex-amination of Stee
9、l PlatesA578/A578M Specification for Straight-Beam UltrasonicExamination of Rolled Steel Plates for Special Applica-tions3. General Requirements and Ordering Information3.1 Material supplied to this material specification shallconform to Specification A20/A20M. These requirements out-line the testin
10、g and retesting methods and procedures, permis-sible variations in dimensions, quality and repair of defects,marking, loading, and ordering information.3.2 In addition to the basic requirements of thisspecification, certain supplementary requirements are availablewhen additional control, testing, or
11、 examination is required tomeet end use requirements. The purchaser is referred to thelisted supplementary requirements in this specification and tothe detailed requirements in Specification A20/A20M.3.3 If the requirements of this specification are in conflictwith the requirements of Specification
12、A20/A20M, the require-ments of this specification shall prevail.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.11 on Steel Plates for Boilers and Pressure Vessels.Current edition appr
13、oved Sept. 1, 2015. Published September 2015. Originallyapproved in 1984. Last previous edition approved in 2010 as A832/A832M 10.DOI: 10.1520/A0832_A0832M-10R15E01.2For ASME Boiler and Pressure Vessel Code applications, see related Specifi-cation SA-832/SA-832M in Section II of that Code.3For refer
14、enced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West
15、Conshohocken, PA 19428-2959. United States14. Manufacture4.1 Steelmaking ProcessThe steel shall be made by one ofthe processes permitted in Specification A20/A20M.4.2 Steelmaking PracticeThe steel shall be killed andshall conform to the fine grain size requirement of Specifica-tion A20/A20M.5. Heat
16、Treatment5.1 All plates shall be normalized and tempered except asallowed by 5.2. The minimum normalizing temperature forGrade 22V shall be 1650F 900C. The minimum normaliz-ing temperature for Grade 23V shall be 1850F 1010C. Theminimum tempering temperature shall be 1250F 675C.5.2 Plates ordered wit
17、hout the heat treatment required by5.1 shall be furnished in either the stress-relieved or theannealed condition. Heat treatment of plates so ordered, toconform to 5.1 and to Table 1, shall be the responsibility of thepurchaser.6. Chemical Composition6.1 The steel shall conform to the requirements a
18、s tochemical composition shown in Table 2.7. Mechanical Properties7.1 Tension Test Requirements:7.1.1 The material as represented by the tension test speci-mens shall conform to the requirements of Table 1.7.2 Notch Toughness Requirements:7.2.1 A transverse Charpy V-notch test from each plate asheat
19、-treated shall have a minimum energy absorption value of40 ftlbf 54 J average of three specimens and 35 ftlbf 48 Jfor one specimen only in the set.7.2.2 The notch toughness test temperature shall be 0F18C.8. Keywords8.1 alloy steel plates; pressure containing parts; pressurevessel steels; steel plat
20、es; steel plates for pressure vesselapplicationsTABLE 1 Tensile RequirementsTensile strength, ksi, MPa 85110 585760Yield strength, min, ksi, MPa 60 415Elongation in 2 in. 50 mm, min, %A18Reduction of area, min, % 45B40CASee Specification A20/A20M for elongation adjustments.BMeasured on round specime
21、n.CMeasured on flat specimen.TABLE 2 Chemical RequirementsNOTE 1Where “. . .” appears there is no requirement.ElementComposition, %Grade 21V Grade 22V Grade 23VCarbonHeat analysis 0.100.15 0.110.15 0.100.15Product analysis 0.080.18 0.090.18 0.080.18ManganeseHeat analysis 0.300.60 0.300.60 0.300.60Pr
22、oduct analysis 0.250.66 0.250.66 0.250.66Phosphorus, max 0.025A0.025AHeat analysis . 0.015 .Product analysis . 0.020 .Sulfur, max 0.025A0.010AHeat analysis . 0.010 .Product analysis . 0.015 .Silicon, maxHeat analysis 0.10 0.10 0.10Product analysis 0.13 0.13 0.13ChromiumHeat analysis 2.753.25 2.002.5
23、0 2.753.25Product analysis 2.633.37 1.882.62 2.633.37MolybdenumHeat analysis 0.901.10 0.901.10 0.901.10Product analysis 0.851.15 0.851.15 0.851.15VanadiumHeat analysis 0.200.30 0.250.35 0.200.30Product analysis 0.180.33 0.230.37 0.180.33TitaniumHeat analysis 0.0150.035 0.030, max .Product analysis 0
24、.0050.045 0.035, max .BoronHeat analysis 0.0010.003 0.0020, max .Product analysis NABNAB.Copper, maxHeat analysis . 0.20 .Product analysis . 0.23 .Nickel, maxHeat analysis . 0.25 .Product analysis . 0.28 .Columbium, maxHeat analysis . 0.07 0.0150.070Product analysis . 0.08 0.0100.075Calcium, maxCHea
25、t analysis . 0.015 0.00050.0150Product analysis . 0.020 NAB Editorially added.AApplies to both heat analysis and product analysis.BNA = Not Applicable.CRare earth metals (REM) may be added in place of calcium, subject toagreement between the producer and the purchaser. In that case, the total amount
26、of REM shall be determined and reported.A832/A832M 10 (2015)12SUPPLEMENTARY REQUIREMENTSSupplementary requirements shall not apply unless specified in the order.Alist of standardized supplementary requirements for use at the option of the purchaser is includedin Specification A20/A20M. Some of those
27、 considered suitable for use with this specification are listedbelow by title.S1. Vacuum Treatment,S2. Product Analysis,S3. Simulated Post-Weld Heat Treatment of MechanicalTest Coupons,S4. Additional Tension Test,S6. Drop-Weight Test (for Material 0.625 in. 16 mm andOver in Thickness),S7. High-Tempe
28、rature Tension Test,S8. Ultrasonic Examination in accordance with Specifica-tion A435/A435M,S9. Magnetic Particle Examination,S11. Ultrasonic Examination in accordance with Specifica-tion A577/A577M,S12. Ultrasonic Examination in accordance with Specifica-tion A578/A578M, andS19. Restricted Chemical
29、 Requirements.ADDITIONAL SUPPLEMENTARY REQUIREMENTSHIGH TEMPERATURE HYDROGEN SERVICEIn addition, the following supplementary requirements are suitable for this application.S62. Temper Embrittlement FactorS62.1 The composition of the steel, based on heat analysis,shall be restricted in accordance wit
30、h the following equations:J 5 Si1Mn! 3 P1Sn! 3104#150 Si, Mn, P and Sn in wt %!Cu#0.20%Ni#0.30%S62.1.1 Lower values of J, Cu, and Ni can be specified byagreement between purchaser and the supplier.S62.1.2 When so specified by the purchaser, the maximumvalue of J shall not exceed 100.S62.1.3 The valu
31、es of J shall be reported.S62.1.4 If the plates are repaired by welding, the composi-tion of the weld deposit shall be restricted in accordance withthe following equations:X 5 10P15Sb14Sn1As!/100#15 P, Sb, Sn and As in ppm!Cu#0.20%Ni#0.30%S62.1.5 The values of X shall be reported.S63. Impact Propert
32、ies After Step CoolingS63.1 The Charpy V-notch impact properties shall be deter-mined as follows:S63.1.1 A sufficient amount of Charpy V-notch test speci-mens shall be taken from the same location from a plate fromeach heat of steel to construct two transition temperaturecurves.S63.1.2 The test spec
33、imens for one transition temperaturecurve shall be given the minimum post-weld heat treatment(PWHT) cycle specified by the purchaser.S63.2 The test specimens for the other transition tempera-ture curve shall be given the PWHT cycle specified in S63.1.2plus the following step cooling heat treatment:H
34、old at 1100F (593C) for 1 h, then cool at 10F (5.6C)/hto 1000F (538C).Hold at 1000F (538C) for 15 h, then cool at 10F (5.6C)/hto 975F (524C).Hold at 975F (524C) for 24 h, then cool at 10F (5.6C)/hto 925F (496C).Hold at 925F (496C) for 60 h, then cool at 5F (2.8C)/hto 875F (468C).Hold at 875F (468C)
35、for 100 h, then cool at 50F(27.8C)/h to 600F (315C).Cool in still air.S63.3 Test the Charpy V-notch test specimens in accordancewith Test Methods and Definitions A370 to determine the40-ft-lbs (55 J) transition temperature from each transitiontemperature curve using a set of three test specimens at
36、eachtest temperature. The test temperatures shall include tests onthe upper and lower shelves and a minimum of four interme-diate temperatures.S63.4 The following requirements shall be met:vTr4012.5 vTr40#50FvTr5512.5 vTr55#10CA832/A832M 10 (2015)13where:vTr40 (vTR55) = the 40-ft-lbs (55 J) transiti
37、on tempera-ture of the material subjected to theminimum PWHT specified by the pur-chaser.vTr40 (vTr55) = the shift of the 40-ft-lbs (55 J) transitiontemperature the of the step cooled ma-terial. (The 40-ft-lbs (55 J) transitiontemperature the of the step cooled ma-terial minus that of the material s
38、ub-jected to the minimum PWHT only).S63.5 The 40-ft-lbs (55 J) transition temperatures for thetwo material conditions shall be reported. (Fig. S1.1)ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned inthis standard. Users
39、of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every fi
40、ve years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical
41、committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, P
42、A 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ S1.1 Transition Temperature Curves Before and After Step Cool Heat TreatmentA832/A832M 10 (2015)14
