ASTM B77-2007(2013) Standard Test Method for Thermoelectric Power of Electrical-Resistance Alloys《电阻合金的热电功率的标准试验方法》.pdf
《ASTM B77-2007(2013) Standard Test Method for Thermoelectric Power of Electrical-Resistance Alloys《电阻合金的热电功率的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM B77-2007(2013) Standard Test Method for Thermoelectric Power of Electrical-Resistance Alloys《电阻合金的热电功率的标准试验方法》.pdf(2页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B77 07 (Reapproved 2013)Standard Test Method forThermoelectric Power of Electrical-Resistance Alloys1This standard is issued under the fixed designation B77; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year of
2、last revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the ther-moelectric power of a metal or alloy with respect to copperwhen
3、the temperatures of the junctions lie between 0 and100C.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not pu
4、rport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet (MSDS) for this product/materialas provided by the manufacturer
5、, to establish appropriatesafety and health practices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B3 Specification for Soft or Annealed Copper Wire3. Terminology3.1 thermoelectric power, Q, nthe electromotive force inan electric c
6、ircuit consisting of two metals when the junctionsbetween them have a difference in temperature of 1C.3.1.1 DiscussionExperimentally, it has been found thatthe thermoelectric power of two metals is not a constant butdepends on the mean temperature of the junctions. However,over a range of temperatur
7、e from 0 to 100C it is usuallysufficient to assume that the thermoelectric power is indepen-dent of temperature so that for this range of temperature:Q 5 E/t2t!where:E = the electromotive force developed in the circuit,t = the higher temperature at one junction, C, andt = the lower temperature at th
8、e other junction, C.4. Significance and Use4.1 The purpose of this method is to determine the suitabil-ity of different metals for use in resistance apparatus in whicha low thermoelectric power is desired. As most electric circuitsare largely composed of copper, the thermoelectric power of aresistan
9、ce metal will generally be measured against copper.5. Test Specimen5.1 The metal or alloy to be tested shall be in the form ofsheet, ribbon, or wire and the test specimen shall be of suchlength that the two ends can be readily maintained at differenttemperatures. At each end of the specimen a copper
10、 lead ofconvenient size shall be fastened. These leads shall make goodelectrical contact with the specimen, such as that obtained bywelding, brazing, or soldering. Slight impurities in the copperhave a negligible effect on the thermoelectric power.NOTE 1When necessary to specify the quality of the c
11、opper leads,reference should be made to Specification B3.6. Procedure6.1 Measurement of TemperatureAs a matter ofprecaution, the average temperature used in determining thethermoelectric power shall be approximately the same as thatto which the material will be subjected in practice, and in nocase s
12、hall the temperature difference between the two junctionsbe less than 20C. The temperature at each of two junctionsshall be measured by a device that is sufficiently accurate todetermine the temperature difference within 5 %. A convenientmethod for determining the temperatures of the junctions is to
13、immerse each junction in separate oil baths maintained at thedesired temperatures. Baths that are stirred and the tempera-tures of which are thermostatically controlled are to bepreferred. However, beakers of oil which are supported byblocks of metal, sand baths, or other means may be used,provided
14、the thermal capacity of these assemblies is such thatwhen the heat is cut off their temperatures will decrease at ratesless than 0.2C/min. The temperature of the oil in each bathmay be determined by a calibrated temperature measuring1This test method is under the jurisdiction of ASTM Committee B02 o
15、nNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.10 on Thermostat Metals and Electrical Resistance Heating Materials.Current edition approved May 1, 2013. Published May 2013. Originallyapproved in 1930. Last previous edition approved in 2007 as B77 07. DOI:10.1520/B0
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
最后一页预览完了!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB7720072013STANDARDTESTMETHODFORTHERMOELECTRICPOWEROFELECTRICALRESISTANCEALLOYS 电阻 合金 热电 功率 标准 试验

链接地址:http://www.mydoc123.com/p-462215.html