1、Designation: D1007 11Standard Specification forsec-Butyl Alcohol1, 2This standard is issued under the fixed designation D1007; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indic
2、ates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers sec-butyl alcohol for use inpaint, varnish, lacquer, and related products.1.2 The values stated in SI units are to be regarded asstanda
3、rd. No other units of measurement are included in thisstandard.1.3 The following applies to all specified limits in thisstandard; for purposes of determining conformance with thisstandard, an observed value or a calculated value shall berounded off “to the nearest unit” in the last right-hand digitu
4、sed in expressing the specification limit, in accordance withthe rounding-off method of Practice E29.1.4 For hazard information and guidance, see the suppliersMaterial Safety Data Sheet.2. Referenced Documents2.1 ASTM Standards:3D268 Guide for Sampling and Testing Volatile Solvents andChemical Inter
5、mediates for Use in Paint and RelatedCoatings and MaterialD1078 Test Method for Distillation Range of Volatile Or-ganic LiquidsD1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)D1353 Test Method for Nonvolatile Matter in VolatileSolvents for Use in Paint, Varnish, Lacquer, and Rela
6、tedProductsD1364 Test Method for Water in Volatile Solvents (KarlFischer Reagent Titration Method)D1613 Test Method for Acidity in Volatile Solvents andChemical Intermediates Used in Paint, Varnish, Lacquer,and Related ProductsD4052 Test Method for Density, Relative Density, and APIGravity of Liquid
7、s by Digital Density MeterD5386 Test Method for Color of Liquids Using TristimulusColorimetryE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE300 Practice for Sampling Industrial Chemicals2.2 U.S. Federal Specification:PPP-C-2020 Chemicals, Liquid, D
8、ry, and Paste: Packagingof43. Properties3.1 sec-Butyl alcohol shall conform to the following re-quirements:Apparent specific gravity:20/20C 0.807 to 0.809or25/25C 0.804 to 0.806Color, Pt-Co scale, maxA10Distillation range, 760 mmHg, C as:Initial boiling point, min 98.0Dry point, max 101.0Nonvolatile
9、 matter, max, mg/100 mL 5Water, max, weight % 0.5Acidity, as acetic acid, max, weight % 0.002B_AInstrumental Pt-Co color determined by Test Method D5386 have been shownto have no statistically significant difference from Pt-Co color determined by TestMethod D1209. However, it is not known whether se
10、c-butyl alcohol was part of thesample set included in the interlaboratory study.BEquivalent to 0.019 mg of KOH per gram of sample.4. Sampling4.1 The material shall be sampled in accordance withPractice E300.5. Test Methods5.1 The properties enumerated in this specification shall bedetermined in acco
11、rdance with the following ASTM methods:5.1.1 Apparent Specific GravityDetermine the apparentspecific gravity at 20 or 25C by a convenient method that isaccurate to the third decimal place. See Guide D268 or TestMethod D4052.1This specification is under the jurisdiction of ASTM Committee D01 on Paint
12、and Related Coatings, Materials, and Applications and is the direct responsibilityD01.35 on Solvents, Plasticizers, and Chemical Intermediates.Current edition approved Nov. 1, 2011. Published November 2011. Originallyapproved in 1949. Last previous edition approved in 2005 as D1007 05. DOI:10.1520/D
13、1007-11.2This compound is also known under the names 2-butanol and secondarybutanol.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary p
14、age onthe ASTM website.4Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/dodssp.daps.dla.mil.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO
15、Box C700, West Conshohocken, PA 19428-2959, United States.5.1.2 ColorTest Method D1209 (see Note A in 3.1).5.1.3 Distillation RangeTest Method D1078 using a tem-perature measuring device having a range of 72 to 126C anda resolution of 0.1C.5.1.4 Nonvolatile MatterTest Method D1353.5.1.5 WaterTest Me
16、thods D1364.5.1.6 AcidityTest Method D1613.6. Packaging and Package Marking6.1 Package size shall be agreed upon between the pur-chaser and the supplier.6.2 Packaging shall conform to applicable carrier rules andregulations or when specified shall conform to Fed. Spec.PPP-C-2020.7. Keywords7.1 methy
17、l ethyl carbinol; sec-butyl alcohol;2hydroxybutaneSUMMARY OF CHANGESCommittee D01 has identified the location of selected changes to this standard since the last issue (D1007 - 05)that may impact the use of this standard. (Approved November 1, 2011.)(1) Revised 5.1.3. (2) Removed Specification E1 fr
18、om 2.1.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such righ
19、ts, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional
20、standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM
21、Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D1007 112
