1、Designation: D 2052 05Standard Test Method forColorfastness of Zippers to Drycleaning1This standard is issued under the fixed designation D 2052; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number i
2、n parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of change inshade and of staining of zipper stringers under drycleaningconditions. This test method
3、is applicable to the textile portionof zipper stringers of all materials.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as the standard. Within the text,the inch-pound units are shown in parentheses. The valuesstated in each system are not exact equivalents
4、; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in nonconformancewith this test method.1.3 This standard does not purport to address all of thesafety problems associated with its use. It is the responsibilityof whoever uses this stand
5、ard to consult and establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 123 Terminology Relating to TextilesD 2050 Terminology Relating to SubassembliesD 2051 Test Method for Durability
6、 of Finish of Zippers toLaunderingD 2053 Test Method for Colorfastness of Zippers to LightD 2054 Test Method for Colorfastness of Zipper Tapes toCrockingD 2057 Test Method for Colorfastness of Zippers to Laun-deringD 2058 Test Method for Durability of Finish of Zippers toDrycleaningD 2059 Test Metho
7、d for Resistance of Zippers to Salt Spray(Fog)D 2060 Test Methods for Measuring Zipper DimensionsD 2061 Test Methods for Strength Tests for ZippersD 2062 Test Methods for Operability of ZippersD 2724 Test Methods for Bonded, Fused, and LaminatedApparel FabricsD 3692 Practice for Selection of Zippers
8、 for Care-LabeledApparel and Household Furnishings2.2 AATCC Methods:Evaluation Procedure 1, AATCC Gray Scale for ColorChange3Evaluation Procedure 3, AATCC Chromatic TransferenceScale33. Terminology3.1 For all terminology related to D13.54, Subassemblies,refer to Terminology D 2050.3.1.1 The followin
9、g terms are relevant to this standard:colorfastness, drycleaning.3.2 For all other terminology relating to textiles, see Termi-nology D 123.4. Summary of Test Method4.1 A specimen of the zipper stringer, in conjunction withmultifiber test fabric is subjected to drycleaning. The dry-cleaned specimen
10、is compared with an original specimen (see10.1) and any change in color of the specimen or staining of themultifiber test cloth is then assessed using the AATCC GrayScale for Color Change or theAATCC Chromatic TransferenceScale, as appropriate.5. Significance and Use5.1 Test Method D 2052 is useful
11、for testing to determine ifthe degree of alteration in shade is satisfactory for the intendedend-use and for determining if unacceptable staining of colorinto adjacent fabric will occur.NOTE 1For guidance in evaluating the results of this test method,refer to Practice D 3692.5.2 This test method is
12、considered satisfactory for accep-tance testing of commercial shipments because the method hasbeen used extensively in the trade for acceptance testing.5.2.1 If there are differences of practical significance be-tween reported test results for two laboratories (or more),1This test method is under th
13、e jurisdiction of ASTM Committee D13 on Textilesand is the direct responsibility of Subcommittee D13.54 on Subassemblies. Themethod was developed in cooperation with the Slide Fastener Assn., Inc.Current edition approved Sept. 1, 2005. Published October 2005. Originallyapproved in 1961. Last previou
14、s edition approved in 2001 as D 2052 01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Technical Manual of
15、the American Association of Textile Chemists andColorists, P.O. Box 12215, Research Triangle Park, NC 27709.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United Sparative tests should be performed to determine if their isa statistical bias betwe
16、en them, using competent statisticalassistance. As a minimum, the test samples should be used thatare as homogeneous as possible, that are drawn from thematerial from which the disparate test results were obtained,and that are randomly assigned in equal numbers to eachlaboratory for testing. Other m
17、aterials with established testvalues may be used for this purpose. The test results from thetwo laboratories should be compared using a statistical test forunpaired data, at probability level chosen prior to the testingseries. If a bias is found, either its cause must be found andcorrected, or futur
18、e test results must be adjusted in consider-ation of the known bias.5.3 The method(s) in this standard along with those in TestMethods D 2051, D 2053, D 2054, D 2057, D 2058, D 2059,D 2060, D 2061, and D 2062 are a collection of proven zippertest methods. They can be used as aids in the evaluation o
19、fzippers without the need for a thorough knowledge of zippers.The enumerated test methods do not provide for the evaluationof all zipper properties. Besides those properties measured bymeans of the enumerated test methods there are other proper-ties that may be important for the satisfactory perform
20、ance ofa zipper. Test methods for measuring those properties have notbeen published either because no practical methods have yetbeen developed or because a valid evaluation of the informa-tion resulting from existing unpublished methods requires anintimate and thorough knowledge of zippers.6. Appara
21、tus6.1 The apparatus shall be as specified in Methods D 2724.6.2 AATCC Chromatic Transference Scale, as specified inAATCC Evaluation Procedure 3.6.3 Gray Scales for Color Change, as specified in AATCCEvaluation Procedure 1.6.4 AATCC Multifiber Test Fabric No. 10.46.5 Undyed Cotton Twill Cloth, weigh
22、ing 270 6 70 g/m2free of finishes.47. Sampling7.1 Lot SampleAs a lot sample for acceptance testing,take at random the number of individual containers from eachshipping carton as directed in an applicable material specifi-cation or other agreement between the purchaser and thesupplier. Consider indiv
23、idual containers from each shippingcarton to be the primary sampling units.NOTE 2An adequate specification or other agreement between thepurchaser and supplier requires taking into account the variability betweenshipping cartons and between zippers in a container to provide a samplingplan with a mea
24、ningful producers risk, consumers risk, acceptablequality level, and limiting quality level.7.2 Laboratory Sample and Test SpecimensAs a labora-tory sample for acceptance testing, take the number of zippersspecified in Section8 at random from each container in the lotsample. Consider the zippers as
25、both the laboratory sample andthe test specimens.8. Number of Specimens8.1 Unless otherwise agreed upon, as when specified in anapplicable material specification, take one zipper at randomfrom each individual container selected for sampling.9. Test Specimen9.1 The test specimen shall consist of appr
26、oximately 40 cm2(6.4 in.2) of zipper stringer taken from each zipper sample. Thespecimen need not be a continuous length.9.2 A duplicate specimen shall be prepared and held forcomparison in evaluating the results of the test.10. Conditioning10.1 The specimens shall be conditioned for at least4hinthe
27、 standard atmosphere for testing textiles prior to beingsubjected to the drycleaning procedure. Preconditioning is notnecessary.11. Procedure11.1 UsingAATCC multifiber test fabric No. 10 for one sideand undyed cotton twill cloth for the other, prepare a bag withinside dimensions of 200 by 100 mm (8
28、by 4 in.) by sewing thetwo superimposed fabrics around three sides. Place the speci-men flatly inside the bag. Close the bag by any convenientmeans such as sewing or stapling the open side.11.2 Dryclean the specimen in the bag as directed inProcedure for Drycleaning D 2724, 10.1 through 10.3.11.3 Re
29、peat the drycleaning procedure through two addi-tional cycles, for a total of three cycles. Remove the specimensfrom the specimen bag and evaluate for color change andstaining as directed in Section 12 of this test method.12. Evaluation12.1 Grade the textile portion of the specimens for changein col
30、or to the nearest one half rating unit as directed inAATCC Evaluation Procedure 1.12.2 Grade the degree of staining of each stripe of themultifiber fabric to the nearest one half rating unit as directedin AATCC Evaluation Procedure 3.13. Report13.1 State that the specimens were tested as directed in
31、ASTM Test Method D 2052. Describe the material or productsampled, and the method of sampling used.13.2 Report the following information:13.2.1 Number of specimens tested,13.2.2 Change in shade for each specimen as the notedgrade on the AATCC Gray Scale for Color Change, and13.2.3 Staining for each m
32、ultifiber stripe on each specimenas the grade on the AATCC Chromatic Transference Scale.14. Precision and Bias14.1 Interlaboratory Test DataAn interlaboratory test wasrun in 1972 using AATCC Method 132 in which randomlydrawn samples of two materials were tested in each of threelaboratories. Each lab
33、oratory used two operators, each ofwhom tested 12 specimens of each material. Calculation ofcomponents of variance was felt to be inappropriate because of4Suitable material is available from Testfabrics, Inc., P.O. Drawer 0, Middlesex,NJ 08846.D2052052the restricted and discontinuous rating scale, t
34、he nonlinearrelationship between the rating scale and color difference unitsand the increased variability in color difference units as the truevalue of the ratings decrease.14.2 PrecisionBased on the observations described in14.1 and on long general practice in the trade, the half-steprating scale h
35、as been found to be satisfactory for determiningthe acceptability or non-acceptability of a given lot. A lot orconsignment of zippers is generally considered as having arating that is significantly worse than a specified value when aspecimen from the lot or consignment has a rating for changein colo
36、r that is more than one-half step below the specifiedrating on the AATCC Gray Scale for Color Change.14.3 BiasNo justifiable statement can be made on the biasof Test Method D 2052 for grading zipper assemblages forchange in color during drycleaning since the true value of thisproperty cannot be esta
37、blished by accepted referee methods.15. Keywords15.1 colorfastness; drycleaning; zipperASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of
38、the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Y
39、our comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your commen
40、ts have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D2052053
