1、Designation: D330 07 (Reapproved 2013)Standard Specification for2-Butoxyethanol1,2This standard is issued under the fixed designation D330; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in pare
2、ntheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification covers 2-butoxyethanol.1.2 The following applies
3、to all specified limits in thisstandard; for purposes of determining conformance with thisstandard, an observed value or a calculated value shall berounded off “to the nearest unit” in the last right-hand digitused in expressing the specification limit, in accordance withthe rounding-off method of P
4、ractice E29.1.3 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.4 For specific hazard information and guidance, see thesuppliers Material Safety Data Sheet for materials listed in thisspecification.2. Referenced Documents2.1 A
5、STM Standards:3D268 Guide for Sampling and Testing Volatile Solvents andChemical Intermediates for Use in Paint and RelatedCoatings and MaterialD1078 Test Method for Distillation Range of Volatile Or-ganic LiquidsD1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)D1364 Test Method f
6、or Water in Volatile Solvents (KarlFischer Reagent Titration Method)D1613 Test Method for Acidity in Volatile Solvents andChemical Intermediates Used in Paint, Varnish, Lacquer,and Related ProductsD4052 Test Method for Density, Relative Density, and APIGravity of Liquids by Digital Density MeterD538
7、6 Test Method for Color of Liquids Using TristimulusColorimetryE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE300 Practice for Sampling Industrial Chemicals2.2 U.S. Federal Standard:PPP-C-2020 Specification for Packaging of Chemicals,Liquid, Dry, a
8、nd Paste43. Properties3.1 2-Butoxyethanol shall conform to the following require-ments:Apparent specific gravity20/20C 0.901 to 0.904or25/25C 0.898 to 0.901Color, Pt-Co scale, max (Note 1) 15Distillation range, 760 mm HgInitial boiling point, C, min 168Dry point, C, max 173Water, weight %, max 0.1Ac
9、idity (free acid as acetic acid),weight %, max0.01 equivalent to 0.093 mg KOH pergram of material_NOTE 1Instrumental Pt-Co color determined by Test Method D5386has been shown to have no statistically significant difference from Pt-Cocolor determined by Test Method D1209. However, it is not knownwhet
10、her 2-butoxyethanol was part of the sample set included in theinterlaboratory study.4. Sampling4.1 The material shall be sampled in accordance withPractice E300.5. Test Methods5.1 The properties enumerated in this specification shall bedetermined in accordance with the following ASTM methods:5.1.1 A
11、pparent Specific GravityDetermine the apparentspecific gravity by any convenient method that is accurate tothe third decimal place, the temperature of both specimen andwater being 20 or 25C (See Guide D268 or Test MethodD4052.)1This specification is under the jurisdiction of ASTM Committee D01 on Pa
12、intand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.35 on Solvents, Plasticizers, and Chemical Intermediates.Current edition approved June 1, 2013. Published June 2013. Originally approvedin 1935. Last previous edition approved in 2007 as D330 07.
13、 DOI: 10.1520/D0330-07R13.2This compound is also known under the name ethylene glycol monobutyl ether.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards
14、Document Summary page onthe ASTM website.4Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.daps.mil.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. Unite
15、d States15.1.2 ColorTest Method D1209 (see Note 1).5.1.3 Distillation RangeTest Method D1078 using a tem-perature measuring device having a range of 148 to 202C anda resolution of 0.1C.5.1.4 WaterTest Method D1364.5.1.5 AcidityTest Method D1613.6. Packaging and Package Marking6.1 Package size to be
16、agreed upon between the purchaserand the supplier.6.2 Packaging shall conform to applicable carrier rules andregulations or when specified shall conform to PPP-C-2020.7. Keywords7.1 ethylene glycol monobutyl ether; 2butoxyethanolASTM International takes no position respecting the validity of any pat
17、ent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision
18、 at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comm
19、ents will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighte
20、d by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D330 07 (2013)2
