1、Designation: D6153 97 (Reapproved 2007)D6153 15Standard Specification forMaterials for Bridge Deck Waterproofing MembraneSystems1This standard is issued under the fixed designation D6153; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revis
2、ion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers deck waterproofing membrane systems designed for use on bridge decks which
3、will receive anasphaltic concrete overlay.1.2 The values stated in SIinch-pound units are to be regarded as the standard. The inch-pound units values given in parenthesesare for information only.mathematical conversions to SI units that are provided for information only and are not consideredstandar
4、d.2. Referenced Documents2.1 ASTM Standards:2D146 Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing and WaterproofingD5167 Practice for Melting of Hot-Applied Joint and Crack Sealant and Filler for EvaluationE96/E96M Test Methods for Water Vapor Transmission
5、 of Materials3. Classification3.1 Bridge deck waterproofing membrane systems covered in this specification include three types:3.1.1 Type ICold applied elastomeric.3.1.2 Type IIHot applied elastomeric.3.1.3 Type IIIPreformed sheet membrane.4. General Requirements4.1 Type I covers cold liquid-applied
6、 chemically curing membrane materials that may be applied to a bridge deck to preventthe passage of water from the bituminous surface course to or through the bridge deck.Amembrane protection course, as specifiedby the membrane manufacturer, is required.4.2 Type II covers hot applied elastomeric mem
7、brane systems that prevent the passage of water from the bituminous surfacecourse to or through the bridge deck. A membrane protection course, as specified by the membrane manufacturer, is required.4.3 Type III covers preformed sheet membrane systems which prevent the passage of water from the bitum
8、inous surface courseto or through the bridge deck.5. Physical Properties5.1 Type I, II, and III:5.1.1 Permeability shall be determined in accordance with Test Method E96/E96M water method.5.1.2 Pliability shall be determined in accordance with Test Method D146, except that the test temperature of th
9、e test specimenshall be 18C 0F (18C) after 24 h and 180 bend over a 146-mm (-in. (6-mm)14-in.) mandrel.6. Performance Requirements6.1 Bridge deck protective membrane materials shall be proposed as systems that shall specify each of the installationcomponents within the system and state the rates of
10、applications, and so forth, where applicable. Materials which are combined1 This specification is under the jurisdiction of ASTM Committee D04 on Road and Paving Materials and is the direct responsibility of Subcommittee D04.32 on Bridgesand Structures.Current edition approved Dec. 1, 2007Jan. 1, 20
11、15. Published January 2008February 2015. Originally approved in 1997. Last previous edition approved in 20032007 asD6153 97 (2003).(2007). DOI: 10.1520/D6153-97R07.10.1520/D6153-15.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org
12、. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit m
13、ay not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Har
14、bor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1in accordance with the system proposal shall meet the requirements stated in performance (applications) specification. Membrane,when tested at the manufacturers recommended rate of application, shall meet the minimum requirement
15、s as stated in Table 1.7. Sampling7.1 Type IThe purchaser shall have the right to sample and test the material at any point prior to being incorporated into thework, to ensure that the material conforms to the specified requirements. If sampled at the point of manufacture, it shall be theresponsibil
16、ity of the manufacturer to determine that the samples taken are representative of the batches or lots proposed forshipment. Samples for testing shall consist of not less than a total sample of 4.5 kg (10 lb) or 3.8 L (1 gal)10 lb (4.5 kg) or 1 gal(3.8 L) of liquid sealant from each batch or lot subm
17、itted for sampling. A batch or lot shall be considered as all finished materialthat was manufactured simultaneously or continuously as a unit prior to packaging. Samples shall be obtained by takingapproximately equal portions from three containers selected at random. Each of the three containers sam
18、ples shall be resealed andmarked for identification, and have application instructions including material safety data sheets in each container.7.2 Type IIThe purchaser shall have the right to sample and test the material at any point prior to its being incorporated intothe work, to ensure that the m
19、aterial conforms to the specified requirements. If sampled at the point of manufacture, it shall be theresponsibility of the manufacturer to determine that the samples taken are representative of the batches or lots proposed forshipment. Samples for testing shall consist of not less than a total sam
20、ple of 4.5 kg (10 lb) or 3.8 L (1 gal)10 lb (4.5 kg) or 1 gal(3.8 L) of sealant from each batch or lot submitted for sampling. A batch or lot shall be considered as all finished material thatwas manufactured simultaneously or continuously as a unit prior to packaging. Samples shall be obtained by ta
21、king three unitsselected at random. Samples and heating shall be in accordance with Practice D5167. Each of the three units sampled shall beresealed and marked for identification, and have application instructions including material safety data sheets in each container.7.3 Type IIIA sample, includin
22、g a seam, sufficient in size to determine compliance with this specification shall be selected atrandom from each 1012 000 yd2 (10 000 m2 (12 000 square yards) ) of fabricated material to provide three test specimens. Forsmaller orders a suitable smaller lot size shall be selected for the random sam
23、pling. Each batch or lot of material shall also bevisually examined for dimensions, appearance, and workmanship. Each test specimen shall be packaged with applicationinstructions and a material safety data sheet.8. Packaging and Package Marking8.1 Type IThe liquid membrane shall be packaged in 20-L
24、(5-gal)5-gal (20-L) sealed containers, or as otherwise specified bythe user. Each container shall be clearly marked with the name and address of the manufacturer, the trade name of the liquidmembrane material, specification designation, the manufacturers batch or lot number, and application instruct
25、ions, unlessotherwise specified in the contract or purchase order.8.2 Type IIThe material shall be packaged at a maximum weight of 25-kg (55-lb)55-lb (25-kg) containers, or as otherwisespecified by the user. Each container shall be clearly marked with the name and address of the manufacturer, the tr
26、ade name ofthe membrane material, specification designation, the manufacturers batch or lot number, and application instructions, includingrecommended application temperature and safe heating temperature, unless otherwise specified in the contract or purchase order.8.3 Type IIIThe material shall be
27、rolled on a substantial core and packaged in a standard commercial manner. Shippingcontainers shall be clearly marked with the name and address of the manufacturer, the trade name of the material, specificationdesignation, the manufacturers batch or lot number, and application instructions, includin
28、g quantity in the package in square feet.TABLE 1 Physical Requirements for MembranePermeability Test Method E96 5.7 NG/PaSm2(perms. 0.1) (max)Pliability(180 bend over a6-mm (14-in.) mandrelat 18C for 24 h)Test Method D146 No BreaksPliability(180 bend over a 14-in. (6-mm) mandrel at0F (18C) for 24 h)
29、Test Method D146 No BreaksD6153 152ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
30、of infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this
31、standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake yo
32、ur views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by co
33、ntacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 153
