1、Designation: E303 93 (Reapproved 2013)Standard Test Method forMeasuring Surface Frictional Properties Using the BritishPendulum Tester1This standard is issued under the fixed designation E303; the number immediately following the designation indicates the year oforiginal adoption or, in the case of
2、revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the procedure for measuringsurface frictional properties using the Briti
3、sh Pendulum SkidResistance Tester.2A method for calibration of the tester isincluded in the Annex.1.2 The British Pendulum Tester is a dynamic pendulumimpact-type tester used to measure the energy loss when arubber slider edge is propelled over a test surface. The tester issuited for laboratory as w
4、ell as field tests on flat surfaces, andfor polish value measurements on curved laboratory specimensfrom accelerated polishing-wheel tests.1.3 The values measured, BPN = British Pendulum (Tester)Number for flat surfaces and polish values for acceleratedpolishing-wheel specimens, represent the fricti
5、onal propertiesobtained with the apparatus and the procedures stated hereinand do not necessarily agree or correlate with other slipperinessmeasuring equipment.1.4 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.5 This standa
6、rd does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 AST
7、M Standards:2E501 Specification for Rib Tire for Pavement Skid-Resistance Tests3. Summary of Test Method3.1 This test method consists of using a pendulum-typetester with a standard rubber slider to determine the frictionalproperties of a test surface.3.2 The test surface is cleaned and thoroughly we
8、tted priorto testing.3.3 The pendulum slider is positioned to barely come incontact with the test surface prior to conducting the test. Thependulum is raised to a locked position, then released, thusallowing the slider to make contact with the test surface.3.4 A drag pointer indicates the British Pe
9、ndulum (Tester)Number. The greater the friction between the slider and the testsurface, the more the swing is retarded, and the larger the BPNreading. Four swings of the pendulum are made for each testsurface.4. Significance and Use4.1 This test method provides a measure of a frictionalproperty, mic
10、rotexture, of surfaces, either in the field or in thelaboratory.4.2 This test method may be used to determine the relativeeffects of various polishing processes on materials or materialcombinations.4.3 The values measured in accordance with this method donot necessarily agree or directly correlate w
11、ith those obtainedutilizing other methods of determining friction properties orskid resistance.NOTE 1BPN and polish values from similar types of surfaces will notbe numerically equal, primarily because of the differences in slide lengthand surface shape. Theoretical correction of the polish values t
12、o obtainnumerical equality, either by mathematical manipulation or by use ofspecial measuring scales is not recommended.5. Apparatus5.1 British Pendulum Tester (Fig. 1)The pendulum withslider and slider mount shall weigh 1500 6 30 g. The distanceof the center of gravity of the pendulum from the cent
13、er ofoscillation shall be 411 6 5 mm (16.2 6 0.2 in.). The testershall be capable of vertical adjustment to provide a slidercontact path of 125 6 1.6 mm (41516 +116 in.) for tests on flatsurfaces, and 76 to 78 mm (3 6116 in.) for tests on1This test method is under the jurisdiction of ASTM Committee
14、E17 on Vehicle- Pavement Systems and is the direct responsibility of Subcommittee E17.23 onSurface Characteristics Related to Tire Pavement Slip Resistance.Current edition approved July 1, 2013. Published September 2013. Originallyapproved in 1961. Last previous edition approved in 2008 as E303 93 (
15、2008).DOI: 10.1520/E0303-93R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,
16、100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1polishing-wheel specimens. The spring and lever arrangementshown in Fig. 2 shall give an average normal slider loadbetween the 76-mm (3-in.) wide slider and test surface of 25006 100 g as measured by the method presc
17、ribed in the annex.5.2 SliderThe slider assembly shall consist of an alumi-num backing plate to which is bondeda6by25by76-mm (14by 1 by 3-in.) rubber strip for testing flat surfaces ora6by25by 32 mm (14 by1by114-in.) rubber strip for testing curvedpolishing-wheel specimens. The rubber compound shall
18、 benatural rubber meeting the requirements of the Road ResearchLaboratory3or synthetic rubber as specified in SpecificationE501.5.2.1 New sliders shall be conditioned prior to use bymaking ten swings on No. 60 grade silicon carbide cloth4orequivalent under dry conditions. The swings shall be madewit
19、h a tester adjusted as in Section 7.3Giles, C. G. Sabey, Barbara E., and Carden, K. W. F., “Development andPerformance of Portable Skid-Resistance Tester,” Road Research Technical PaperNo. 66, Road Research Laboratory, Dept. of Scientific and Industrial Research,England, 1964.Kummer, H. W. and Moore
20、, D. F. “Concept and Use of the British PortableSkid-Resistance Tester,” Report No. 6, PDH-PSV Joint Road Friction Program,Dept. of Mechanical Engineering, The Pennsylvania State University, State College,PA 16802, June 1963.4The sole source of supply of the apparatus known to the committee at this
21、timeis available from 3 M Co., St. Paul, MN, under the trade name of Type BSafety-Walk. If you are aware of alternative suppliers, please provide this informa-tion to ASTM International Headquarters. Your comments will receive carefulconsideration at a meeting of the responsible technical committee,
22、1which you mayattend.FIG. 1 British Pendulum TesterFIG. 2 Schematic Drawing of Pendulum Showing Spring and Le-ver ArrangementE303 93 (2013)25.2.2 Wear on the striking edge of the slider shall not exceed3.2 mm (18 in.) in the plane of the slider or 1.6 mm (116 in.)vertical to it, as illustrated in Fi
23、g. 3.5.3 Accessories:5.3.1 Contact path gage shall consist of a thin ruler suitablymarked for measuring contact path length between 124 and 127mm (478 and 5.0 in.) or between 75 and 78 mm (21516 and 3116in.) as required for the particular test.5.3.2 Miscellaneous equipment, such as water container,s
24、urface thermometer, and brush is recommended.6. Test Specimen6.1 FieldField test surfaces shall be free of loose particlesand flushed with clean water. The test surface does not have tobe horizontal provided the instrument can be leveled inworking position using only the leveling screws and thependu
25、lum head will clear the surface.6.2 LaboratoryLaboratory test panels shall be clean andfree of loose particles and shall be held rigidly so as not to bemoved by the force of the pendulum.6.2.1 Flat laboratory test panels shall have a test surface ofat least 89 by 152 mm (312 by 6 in.).6.2.2 Accelera
26、ted laboratory polishing-wheel speci-mensshall have a test surface of at least 44 by 89 mm (134 by312 in.) and shall be curved in the arc of a circle 406 mm (16in.) in diameter.7. Preparation of Apparatus7.1 LevelingLevel the instrument accurately by turningleveling screws until the bubble is center
27、ed in the spirit level.7.2 Zero Adjustment Raise pendulum mechanism by loos-ening locking knob (directly behind pendulum pivot) and turneither of pair of head movement knobs at center of tester toallow slider to swing free of test surface. Tighten locking knobfirmly. Place pendulum in release positi
28、on and rotate the dragpointer counter clockwise until it comes to rest against adjust-ment screw on pendulum arm. Release pendulum and notepointer reading. If reading is not zero, loosen locking ring androtate friction ring on bearing spindle slightly and lock again.Repeat test and adjust friction r
29、ing until the pendulum swingcarries pointer to zero.7.3 Slide Length Adjustment:7.3.1 With pendulum hanging free, place spacer underadjusting screw of lifting handle. Lower pendulum so edge ofslider just touches surface. Lock pendulum head firmly, raiselifting handle, and remove spacer.7.3.2 Raise s
30、lider by lifting handle, move pendulum to rightlower slider, and allow pendulum to move slowly to left untiledge of slider touches surface. Place gage beside slider andparallel to direction of swing to verify length of contact path.Raise slider, using lifting handle, and move pendulum to left,then s
31、lowly lower until slider edge again comes to rest onsurface. If the length of the contact path is not between 124 and127 mm (478 and 5.0 in.) on flat test specimens or between 75and 78 mm (21516 and 3116 in.) on curved polishing-wheelspecimens, measured from trailing edge to trailing edge of therubb
32、er slide, adjust by raising or lowering instrument with thefront leveling screws. Readjust level of instrument if necessary.Place pendulum in release position and rotate the drag pointercounter-clockwise until it comes to rest against adjustmentscrew on pendulum arm.8. Procedure8.1 Apply sufficient
33、water to cover the test area thoroughly.Execute one swing, but do not record reading.NOTE 2Always catch the pendulum during the early portion of itsreturn swing. While returning the pendulum to its starting position, raisethe slider with its lifting handle to prevent contact between the slider andth
34、e test surface. Prior to each swing, the pointer should be returned untilit rests against the adjustment screw.8.2 Without delay, make four more swings, rewetting thetest area each time and record the results.NOTE 3Care should be taken that the slider remains parallel to the testsurface during the s
35、wings, and does not rotate so that one end rather thanthe entire striking edge makes the initial contact. Available data indicatethat tilting of the slider may cause erroneous BPN readings.Installation of a small flat spring will relieve the problem. The springcan be inserted into a slot in the spri
36、ng clip and the assembly secured bythe cotter pin as shown in Fig. 4.The free ends of the spring can rest onthe slider backing plate to restrain the slider from tilting.8.3 Recheck the slide contact length in accordance with 4.3.9. Report9.1 Report the following information:9.1.1 Individual values i
37、n BPN or polish value units,9.1.2 Temperature of the test surface,9.1.3 Type, age, condition, texture and location of testsurface,9.1.4 Type and source of aggregate for polish value tests,and9.1.5 Type and age of the rubber slider.10. Precision and BiasNOTE 4The following material pertains only to t
38、he precision and biasof BPN units.10.1 Repeated tests show standard deviations as follows:British rubber sliders 1.0 BPN unitRubber sliders (conforming toSpecification E501)1.2 BPN unitsIn both cases the upper quartile of variability is representedin prevailing test instruments.As there is no marked
39、 correlationFIG. 3 Slider Assembly Illustrating the Maximum Wear on Strik-ing EdgeE303 93 (2013)3between standard deviation and arithmetic mean of sets of testvalues, it appears that standard deviations are pertinent to thistest regardless of the average skid resistance being tested.10.2 The relatio
40、nship, if any exists, of observed BPN unitsto some “true” value of skid resistance has not and probablycannot be studied. As a result, precision and bias of this test inrelation to a true skid resistance measure cannot be evaluated,and only repeatability is given for the method.10.3 Determine the te
41、sting error as follows:E 5 tn21/2(1)where:E = testing error,t = normal curve of 1.96 or 2.0 rounded, = standard deviation of individual test results (BPNunits), andn = number of tests.10.4 In order to ensure that the testing error stays within 1.0BPN unit at a 95 % confidence level (corresponding to
42、 anormal curve of 1.96 or 2.0 rounded), the following samplesizes are needed:British natural rubber sliders 4Synthetic rubber sliders (conforming to Specification E501)5ANNEX(Mandatory Information)A1. CALIBRATIONA1.1 Weight of PendulumThe pendulum arm withmounted rubber slider shall be disconnected
43、from the instru-ment and weighed to the nearest 1 g.A1.2 Center of GravityThe center of gravity of thependulum with a mounted rubber slider shall be determined byplacing the pendulum assembly over a knife edge and experi-mentally locating the point of balance as shown in Fig. A1.1.The adapter nut sh
44、all be held at the far end of the arm by a lightpaper wedge. After the point of balance has been obtained, theposition of the balance weight shall be adjusted until the slidesof the pendulum foot are horizontal.A1.3 Distance of Center of Gravity from Center ofOscillationWith the pendulum reconnected
45、 to thetester and knurled bearing cap removed, distance shall bemeasured from the center of oscillation (center of bearing nut)to the point of balance (center of gravity). This distance shallbe measured directly to the nearest 1 mm (0.04 in.).A1.4 Slider Load The pendulum shall be clamped to aholder
46、 attached to the scale plate of the tester and the testerplaced and leveled on a tripod stand as shown in Fig. A1.2.Insert the spacer. Adjust the pan balance with a bearingassembly (see Note A1.1) on one pan and tare weights on theFIG. 4 Spring Clip and Spring to Inhibit Slider RotationFIG. A1.1 Pen
47、dulum Assembly Showing Location of the Point of BalanceE303 93 (2013)4other pan so that the balance pointer is at center scale reading.The pendulum, with a slider, shall be lowered with the verticalheight knobs of the tester until the slider is approximately 0.25mm (0.01 in.) from the top surface of
48、 the bearing assembly.Lock vertical height knob and remove the spacer. This willcause an unbalance which shall be partially compensated byadding weights to the opposite pan to bring the indicator towithin approximately 200 g of the center scale reading. Tocomplete the balance procedure, the pointer
49、is returned to thecenter scale reading, by adding water slowly into a graduatedcylinder. Empty the cylinder and repeat pouring. Record theaverage weight required to raise slider so that the balancepointer is at the center of scale (see Note A1.2). If the average,normal slider load between the 76-mm (3-in.) wide slider andthe pan balance is not within the requirements stated in 2.1.1adjust the spring tension nut illustrated in Fig. 2 and redeter-mine the slider load.NOTE A1.1The bearing assembly may be a “ladder” bearing with arigid, free-moving
