1、Designation: F1750 11 (Reapproved 2015) An American National StandardStandard Specification forPaintball Marker Threaded-Propellant Source Interface1This standard is issued under the fixed designation F1750; the number immediately following the designation indicates the year oforiginal adoption or,
2、in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the male and female threadedconnectors used to interfac
3、e a propellant source with a workingpressure of 10 342 kPa (1800 psig) or less to a paintballmarker.1.2 The values stated in SI units are to be regarded asstandard. The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns, if any
4、, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D2240 Test Method for Rubber PropertyDurometer Hard
5、-nessF2272 Specification for Paintball Markers2.2 ANSI Standard:3ANSI Y14.5M1994 Dimensioning and Tolerancing2.3 CGA Standard:4CGA-320 .825-14NGO-RH-EXT (Flat Nipple)2.4 Federal Standard:5FED-STD-H28/9A 24 March 1989 Federal Standard Screw-Thread Standards for Federal Services Section 9 GasCylinder
6、Valve Outlet and Inlet Threads2.5 Military Standard:5MS28775 O-Ring Dash Sizes3. Connector Gender Assignment3.1 The female connector is that connector which is config-ured as part of the paintball marker conforming to SpecificationF2272.3.2 The male connector is that connector which is config-ured a
7、s part of the propellant source.4. Materials and Manufacture4.1 The male and female connectors shall be made frommaterials that are compatible with CO2, compressed air, orgaseous nitrogen. The materials and processes used to manu-facture male and female connectors shall result in items withmechanica
8、l strength sufficient to pass a 20 684-kPa (3000-psig)proof pressure check without failure or any degradation tofunction.4.2 The O-ring seal shall be made from an elastomercompatible with CO2, compressed air, or gaseous nitrogen. TheO-ring seal shall have a hardness that will register a Type Adurome
9、ter reading of 90 6 5. The O-ring shall conformdimensionally to MS28775-015 and conform to Test MethodD2240.4.3 The O-ring seal shall be installed on the male connectorin the groove described by Dimensions C and K on Fig. 1.4.4 The male and female connectors shall not have anysharp edges or hanging
10、burrs. All sharp edges will be brokenR.38 MAX (R.015 MAX).5. Performance5.1 The interface is intended for use with compressed air,gaseous nitrogen, or CO2.5.2 The maximum operating pressure of the interface is10 342 kPa (1800 psig).5.3 The maximum allowable leakage at 10 342 kPa (1800psig) is 0.1 cm
11、3/min.5.4 The male connector shall incorporate a means forpropellant shutoff that shall meet the maximum leakage re-quirement.5.5 When the male and female connectors are joined andpressurized, together they shall meet the maximum leakagespecification.1This specification is under the jurisdiction of
12、ASTM Committee F08 on SportsEquipment, Playing Surfaces, and Facilities and is the direct responsibility ofSubcommittee F08.24 on Paintball and Equipment.Current edition approved April 1, 2015. Published August 2015. Originallyapproved in 1996. Last previous edition approved in 2011 as F1750 11. DOI
13、:10.1520/F1750-11R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standa
14、rds Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.4Available from Compressed Gas Association (CGA), 1725 Jefferson DavisHwy., Suite 1004, Arlington, VA 22202-4102.5Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Wash
15、ington, DC 20401.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States16. Physical Envelope6.1 The male connector shall conform to the physicalenvelope described in Fig. 1.6.2 The female connector shall conform to the physicalenvelope descr
16、ibed in Fig. 2.7. Valve Core7.1 The male connector may contain, as a means of propel-lant shutoff, a valve core to provide for an automatic shutoff offlow at the time of disconnection. The stem of the valve coreshall not protrude beyond the face of the male connector, thatsurface designated as Datum
17、 B in Fig. 1. Full flow must beachieved when the stem of the valve core has been depressed1.78 mm (0.070 in.) from the surface designated as Datum B inFig. 1. The stem of the valve core shall be able to be depressedto a minimum depth of 2.54 mm (0.100 in.) below Datum Bwithout being damaged. If a va
18、lve core is not used there shallnot be any feature of the male connector which will interferewith the valve opening feature of the female fitting.8. Venting8.1 The female connector shall have a provision for the selfventing of residual gas pressure prior to the disconnection ofthe threaded interface
19、. Fig. 2 (Dimensions D and H) shows arecommended location and feature size for a vent hole.9. Operating Temperatures9.1 The interface shall have an operating range from 40to + 54C (40 to + 130F).10. Flow10.1 The interface shall flow not less than 170 sL/min at 689kPa (6 S.C.F.M. at 100 psid).10.2 Th
20、e feature allowing flow through the female connec-tor shall lie within the area designated by minimum DimensionMinFig. 2.10.3 The feature allowing flow through the male connectorshall lie within the area designated by Dimension M in Fig. 1.11. Keywords11.1 paintball marker; propellantDimension SI In
21、chesA 22.86 min 0.900 minB 18.46/17.02 0.727/0.670C 14.66 0.08 0.577 0.003D R.250.13 R.0100.005E 17.60/17.40 0.693/0.685F 16.66 min 0.656 minG 6.350.13 0.2500.005H 2.54 0.5 0.100 0.020J 1.020.13 0.0400.005K 2.160.08 0.0850.003N 0.38 0.13 45 3 0.015 0.005 45 3M R 5.54 0.38 R.218 0.015FIG. 1 Male Conn
22、ectorDimension SI InchesA 15.75 0.13 0.620 0.005B 5.080.13 0.2000.005C 1.910.13 0.0750.005D 7.320.13 0.2880.005E 3.180.13 0.1250.005F 17.78/17.63 0.700/0.694G 0.89 min 0.035 minH 0.79 min 0.031 minJ R.64 max R.025 maxK 9.40 min 0.370 minM R 4.78 max R.188 maxO 21.59 0.254 0.85 0.010FIG. 2 Female Con
23、nectorF1750 11 (2015)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringeme
24、nt of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or
25、for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views kno
26、wn to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting AST
27、M at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 11 (2015)3
