ASTM F1807-2013 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Tempe.pdf
《ASTM F1807-2013 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Tempe.pdf》由会员分享,可在线阅读,更多相关《ASTM F1807-2013 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Tempe.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F1807 13 An American National StandardStandard Specification forMetal Insert Fittings Utilizing a Copper Crimp Ring for SDR9Cross-linked Polyethylene (PEX) Tubing and SDR9Polyethylene of Raised Temperature (PE-RT) Tubing1This standard is issued under the fixed designation F1807; the num
2、ber immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope
3、*1.1 This specification covers metal insert fittings and coppercrimp rings for use with cross-linked polyethylene (PEX)tubing in38,12,58,34,1,114,112, and 2 in. nominal diametersthat meet the requirements for Specifications F876 and F877and for use with polyethylene of raised temperature (PE-RT)tubi
4、ng in38,12,58,34 and 1 in. and 114 in. nominal diametersthat meet the requirements of Specifications F2623 and F2769.These fittings are intended for use in 100 psi (689.5 kPa) cold-and hot-water distribution systems operating at temperaturesup to, and including, 180F (82C). The requirements formater
5、ials, workmanship, dimensions, and markings to be usedon the fittings and rings are also included.1.2 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are mathemati-cal conversions to SI units which are provided for informationonly and are not
6、considered the standard.1.3 Compliance with this specification requires that thesefittings be tested and certified to Specification F877 when usedwith PEX tubing and Specification F2769 when used withPE-RT tubing.1.4 This standard does not purport to address all of thesafety concerns, if any, associ
7、ated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2A269 Specification for Seamless and Welded AusteniticStainl
8、ess Steel Tubing for General ServiceA276 Specification for Stainless Steel Bars and ShapesA312/A312M Specification for Seamless, Welded, andHeavily Cold Worked Austenitic Stainless Steel PipesB16/B16M Specification for Free-Cutting Brass Rod, Barand Shapes for Use in Screw MachinesB62 Specification
9、for Composition Bronze or Ounce MetalCastingsB75 Specification for Seamless Copper TubeB88 Specification for Seamless Copper Water TubeB124/B124M Specification for Copper and Copper AlloyForging Rod, Bar, and ShapesB140/B140M Specification for Copper-Zinc-Lead (RedBrass or Hardware Bronze) Rod, Bar,
10、 and ShapesB283 Specification for Copper and Copper-Alloy Die Forg-ings (Hot-Pressed)B371/B371M Specification for Copper-Zinc-Silicon AlloyRodB584 Specification for Copper Alloy Sand Castings forGeneral ApplicationsB967/B967M Specification for Copper-Zinc-Tin-BismuthAlloy Rod, Bar and WireD1600 Term
11、inology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsE18 Test Methods for Rockwell Hardness of Metallic Ma-terialsF412 Terminology Relating to Plastic Piping SystemsF876 Specification for Crosslinked Polyethylene (PEX) Tub-
12、ingF877 Specification for Crosslinked Polyethylene (PEX) Hot-and Cold-Water Distribution SystemsF2623 Specification for Polyethylene of Raised Temperature(PE-RT) SDR 9 TubingF2769 Specification for Polyethylene of Raised Temperature(PE-RT) Plastic Hot and Cold-Water Tubing and Distri-bution Systems1
13、This standard is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.Current edition approved May 1, 2013. Published May 2013. Originallyapproved in 1997. Last previous edition approved in 2012 as F1807 12. DOI:10.
14、1520/F1807-13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the en
15、d of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States12.2 ASME Standards:3B1.20.1 Pipe Threads General Purpose (Inch)B16.18 Cast Copper Alloy Solder Joint Pressure FittingsB16.22 Wrought Copper and Copper Alloy Solder Join
16、tPressure Fittings2.3 Manufacturers Standardization Society Standard:4SP-104 Wrought Copper Solder Joint Pressure Fittings2.4 NSF International Standard:5Standard No. 14 for Plastic Piping Components and RelatedMaterialsStandard No. 61 for Drinking Water System Components-Health Effects2.5 EN Standa
17、rds6EN 12164 Copper and Copper Alloys-Rod for Free Machin-ing PurposesEN 12165 Copper and Copper Alloys-Wrought and Un-wrought Forging StockEN 1982 Copper and Copper Alloys, Ingots and Castings3. Terminology3.1 Definitions are in accordance with Terminology F412and abbreviations are in accordance wi
18、th Terminology D1600,unless otherwise indicated.4. Classification4.1 This specification covers one class of fittings and coppercrimp rings suitable for use with PEX tubing that meet therequirements of Specifications F876 or F877 or with PE-RTtubing that meet the requirements of Specifications F2623
19、andF2769 or a combination thereof.5. Materials and Manufacture5.1 FittingsThe fittings shall be made from one of thefollowing metals:5.1.1 Wrought CopperWrought copper fittings shall bemade from material meeting the requirements of SpecificationB75 or B88 for one of the following coppers: copper UNS
20、 Nos.C10200, C10300, C10800, or C12200.5.1.2 Cast Copper AlloysCast copper alloy fittings shallbe made from material meeting the requirements of Specifica-tion B584, copper alloy UNS Nos. C84400, C83800, C87710,C87850 or C89844 or Specification B62, copper alloy UNSNo. C83600, or Standard EN 1982, c
21、opper alloy EN SymbolCuSn4Zn6Pb3C.5.1.3 Machined BrassMachined brass fittings shall bemade from material meeting the requirements of SpecificationB140/B140M copper alloy UNS No. C31400, or SpecificationB16/B16M, Copper Alloy UNS No. C36000, SpecificationB124/B124M copper alloy UNS No. C48600, or C87
22、700, orSpecification B371/B371M CopperAlloy UNS No. C69300, orStandard EN 12164, Copper Alloy CW614N, or Copper AlloyUNS No. C27450, or Specification B967/B967M copper alloyUNS No. C49260 or C49340.5.1.4 Forged BrassForged brass fittings shall be madefrom material meeting the requirements of Specifi
23、cation B283,Copper Alloy UNS Nos. C27450, C35330, C36500, C37700,C46400, C48600, C49260, C49340, C69300 or C87700.5.1.5 Stainless SteelStainless steel fittings shall be madefrom material meeting requirements of Specification A312/A312M, stainless steel alloy 304, 304L, 316 or 316L, (UNSNos. S30400,
24、S30403, S31600 or S31603), or SpecificationA269, stainless steel alloy 304, 304L, 316, 316L (UNS Nos.S30400, S30403, S31600 or S31603), or Specification A276,Stainless steel alloy 304, 401L, 316, or 316L (UNS Nos.S30400, S30403, S31600 or S31603)5.2 Crimp RingsCrimp rings shall be made from copperUN
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF18072013STANDARDSPECIFICATIONFORMETALINSERTFITTINGSUTILIZINGACOPPERCRIMPRINGFORSDR9CROSSLINKEDPOLYETHYLENEPEXTUBINGANDSDR9POLYETHYLENEOFRAISEDTEMPEPDF
![提示](http://www.mydoc123.com/images/bang_tan.gif)
链接地址:http://www.mydoc123.com/p-535724.html