1、Designation: F2418 16F2418 16aStandard Specification forPolypropylene (PP) Corrugated Wall Stormwater CollectionChambers1This standard is issued under the fixed designation F2418; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the
2、 year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers requirements, test methods, materials, and marking for polypropylene (PP), open bo
3、ttom, buriedchambers of corrugated wall construction used for collection, detention, and retention of stormwater runoff. Applications includecommercial, residential, agricultural, and highway drainage, including installation under parking lots and roadways.1.2 Chambers are produced in arch shapes wi
4、th dimensions based on chamber rise, chamber span, and wall stiffness. Chambersare manufactured with integral feet that provide base support. Chambers may include perforations to enhance water flow.Chambers must meet test requirements for arch stiffness, flattening, and accelerated weathering.1.3 An
5、alysis and experience have shown that the successful performance of this product depends upon the type and depth ofbedding and backfill, and care in installation. This specification includes requirements for the manufacturer to provide chamberinstallation instructions to the purchaser.1.4 The values
6、 stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information only and are not considered standard.1.5 This standard does not purport to address water quality issues or hydraulic performance requi
7、rements associated with itsuse. It is the responsibility of the user to ensure that appropriate engineering analysis is performed to evaluate the water qualityissues and hydraulic performance requirements for each installation.1.6 The following safety hazards caveat pertains only to the test method
8、portion, Section 6, of this specification:This standarddoes not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practices and determine the applicability of regulatory limi
9、tations prior to use.2. Referenced Documents2.1 ASTM Standards:2D256 Test Methods for Determining the Izod Pendulum Impact Resistance of PlasticsD618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD790 Test Methods for Flexural Properties of Unreinfo
10、rced and Reinforced Plastics and Electrical Insulating MaterialsD1600 Terminology for Abbreviated Terms Relating to PlasticsD2122 Test Method for Determining Dimensions of Thermoplastic Pipe and FittingsD2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parall
11、el-Plate LoadingD2990 Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of PlasticsD4101 Specification for Polypropylene Injection and Extrusion MaterialsD4329 Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of PlasticsD6992 Test Method for Accelerated Ten
12、sile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-TemperatureSuperposition Using the Stepped Isothermal MethodF412 Terminology Relating to Plastic Piping SystemsF2787 Practice for Structural Design of Thermoplastic Corrugated Wall Stormwater Collection Chambers1 This specification
13、 is under the jurisdiction ofASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.65 on Land Drainage.Current edition approved April 1, 2016Aug. 1, 2016. Published June 2016August 2016. Originally approved in 2004. Last previous edition approved in 201320
14、16 asF2418-13.-16. DOI: 10.1520/F2418-16.10.1520/F2418-16A.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.Th
15、is document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editi
16、ons as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.
17、 United States13. Terminology3.1 Definitions:3.1.1 Definitions used in this specification are in accordance with the definitions in Terminology F412, and abbreviations arein accordance with Terminology D1600, unless otherwise indicated.3.1.2 chamberan arch-shaped structure manufactured of thermoplas
18、tic with an open-bottom that is supported on feet and maybe joined into rows that begin with, and are terminated by, end caps (see Fig. 1).3.1.3 corrugated walla wall profile consisting of a regular pattern of alternating crests and valleys (see Fig. 2).3.1.4 crestthe element of a corrugation locate
19、d at the exterior surface of the chamber wall, spanning between two webelements (see Fig. 2).3.1.5 crownthe center section of a chamber typically located at the highest point as the chamber is traversed circumferentially.3.1.6 end capa bulkhead provided to begin and terminate a chamber, or row of ch
20、ambers, and prevent intrusion of surroundingembedment materials.3.1.7 foota flat, turned out section that is manufactured with the chamber to provide a bearing surface for transfer of verticalloads to the bedding (see Fig. 1).3.1.8 inspection portan opening in the chamber wall that allows access to
21、the chamber interior.3.1.9 nominal heighta designation describing the approximate vertical dimension of the chamber at its crown (see Fig. 1).3.1.10 nominal widtha designation describing the approximate outside horizontal dimension of the chamber at its feet (seeFig. 1).3.1.11 periodthe length of a
22、single repetition of the repeated corrugation, defined as the distance from the centerline of avalley element to the centerline of the next valley element (see Fig. 2).3.1.12 risethe vertical distance from the chamber base (bottom of the chamber foot) to the inside of a chamber wall valleyelement at
23、 the crown as depicted in Fig. 1.3.1.13 spanthe horizontal distance from the interior of one sidewall valley element to the interior of the other sidewall valleyelement as depicted in Fig. 1.3.1.14 valleythe element of a corrugated wall located at the interior surface of the chamber wall, spanning b
24、etween two webs(see Fig. 2).3.1.15 webthe element of a corrugated wall that connects a crest element to a valley element (see Fig. 2).4. Materials and Manufacture4.1 This specification covers chambers made from virgin and rework PP plastic materials as defined by material mechanicalrequirements and
25、chamber performance requirements.4.2 Polypropylene materials may be combined with copolymers, pigments, and impact modifiers which together are suitable formanufacture. Manufactured chamber and end cap material shall meet or exceed the requirements of designation PP0330B99945,Specification D4101. Th
26、e minimum amount of polypropylene plastic in the material shall be 95 % by weight. The minimum tensilestress at yield, Test Method D638, shall not be less than 3 100 psi (21 MPa). The minimum flexural modulus (1 % secant), TestMethod D790, Procedure A, shall not be less than 145 000 psi (1 000 MPa).
27、 The minimum Izod Impact Resistance at 73 F (23C), Method A in Test Method D256, shall not be less than 4 ft-lb/in. (215 J/m). Materials shall meet the creep requirements in5.3.5 and 5.3.6 of this standard.NOTE 1The model chamber shown in this standard is intended only as a general illustration. Any
28、 chamber configuration is permitted, as long as itmeets all the specified requirements of this standard.FIG. 1 Model ChamberF2418 16a2NOTE 1The polypropylene melt flow rate is specified for chamber manufacture by injection molding. The melt flow rate may be less than 10 if themanufactured chamber me
29、ets all other requirements in this standard. This cell class will be re-evaluated when new chamber classifications are added toTable 1.NOTE 2Polypropylene plastic is prepared by the polymerization of propylene or propylene with other alpha olefins as described in SpecificationD4101.4.3 Rework Materi
30、alClean rework material generated from the manufacturers own chambers may be used by the samemanufacturer, using the same type and grade resin, provided that the chambers produced meet all the requirements of thisspecification.5. Requirements5.1 Chamber Description5.1.1 Chambers shall be produced in
31、 arch shapes symmetric about the crown with corrugated wall and integral feet for basesupport (see Fig. 1). Any arch shape is acceptable provided all the requirements of this specification are met.NOTE 3For purposes of structural optimization, the wall geometry (for example, corrugation height, cres
32、t width, valley width, and web pitch) mayvary around the chamber circumference.5.1.2 Chambers shall be produced with maximum span at the base of the chamber (bottom of the chamber foot).5.1.3 Chambers may include access ports for inspection or cleanout. Chambers with access ports shall meet the requ
33、irementsof this standard with access ports open and closed.5.1.4 Chambers may include perforations. Perforations shall be cleanly fabricated in a size, shape, and pattern determined bythe manufacturer. Chambers with perforations shall meet the requirements of this standard.5.1.5 Chamber sections sha
34、ll be manufactured to connect at the ends to provide rows of various lengths. Joints shall beconfigured to prevent intrusion of the surrounding embedment material and shall be capable of carrying the full load for whichthe chamber is designed.5.1.6 Each row of chambers shall begin and terminate with
35、 an end cap.NOTE 1The corrugation profile shown in this standard is intended only as a general illustration. Any corrugation pattern is permitted, as long as itmeets all the specified test requirements of this standard.FIG. 2 Model Corrugated WallTABLE 1 Classifications, Dimensions, and TolerancesCh
36、amberClassificationNominalHeightNominalWidth Rise SpanMinimumFootWidthWallThicknessMinimumArchStiffnessConstantAChamberClassification DesignationB NominalHeightNominalWidthRise SpanWallThicknessAverage Minimumin. (mm) in. (mm)Averagein. (mm)Tolerancein (mm)Averagein. (mm)Tolerance in (mm)in. (mm) in
37、. (mm) in. (mm) lb/ft/%1225 12 (305) 25 (635) 9.8 (249) 0.4 (10) 15.3 (389) 0.4 (10) 4.0 (100) 0.150 (3.8) 0.140 (3.5) 3001225 . 12 (305) 25 (635) 9.8 (249) 0.4 (10) 15.3 (389) 0.4 (10) 4.0 (100) 0.150 (3.8) 0.140 (3.5) 3001633 . 16 (406) 33 (838) 13.5 (343) 1.0 (25) 25.0 (635) 1.0 (25) 4.0 (100) 0.
38、130 (3.3) 0.120 (3.0) 3003051 . 30 (762) 51 (1295) 27.0 (686) 1.0 (25) 44.0 (1118) 1.1 (28) 4.0 (100) 0.180 (4.6) 0.165 (4.2) 3004576 45 (1143) 76 (1930) 40.5 (1029) 1.0 (25) 64.0(1626)1.6 (41) 5.0 (127) 0.225 (5.7) 0.205 (5.2) 2504576 SS 45 (1143) 76 (1930) 40.5 (1029) 1.0 (25) 64.0 (1626) 1.6 (41)
39、 5.0 (127) 0.225 (5.7) 0.205 (5.2) 2504576 LS 45 (1143) 76 (1930) 41.0 (1041) 1.0 (25) 67.0 (1702) 1.6 (41) 5.0 (127) 0.225 (5.7) 0.205 (5.2) 25060 101 60 (1524) 101 (2565) 54.0 (1372) 1.4 (34) 84.5(2146)2.1 (54) 8.0 (203) 0.245 (6.2) 0.225 (5.7) 25060 101 . 60 (1524) 101 (2565) 54.0 (1372) 1.4 (34)
40、 84.5 (2146) 2.1 (54) 8.0 (203) 0.245 (6.2) 0.225 (5.7) 250AThe The values for arch stiffness should not be considered comparable to values of pipe stiffness.BThe designation indicates production tolerances of chamber variations within the same classification group.F2418 16a35.1.7 Chamber classifica
41、tions, dimensions, and tolerances are provided in Table 1. Chamber classifications are based on thenominal height and nominal width of the chambers, as illustrated in Fig. 1. Classifications shall be manufactured with the specifiedrise and span with tolerances, minimum foot width, and minimum wall t
42、hickness.5.2 WorkmanshipThe chambers shall be homogeneous throughout and essentially uniform in color, opacity, density, and otherproperties. The interior and exterior surfaces shall be free of chalking, sticky, or tacky material. The chamber walls shall be freeof cracks, blisters, voids, foreign in
43、clusions, or other defects that are visible to the naked eye and may affect the wall integrity.5.3 Physical and Mechanical Properties of Finished Chamber:5.3.1 Wall ThicknessChambers shall have minimum and average wall thicknesses not less than the minimum wall thicknessesshown in Table 1 when measu
44、red in accordance with 6.2.1.5.3.2 Minimum Foot WidthChambers shall have a foot width not less than the minimum foot width as shown in Table 1 whenmeasured in accordance with 6.2.2 (see also Fig. 1).5.3.3 Rise and Span DimensionsChambers shall meet the rise and span dimension requirements shown in T
45、able 1 whenmeasured in accordance with 6.2.3 and 6.2.4 (see also Fig. 1).5.3.4 Deviation From StraightnessThe chamber and its support feet shall not have a deviation from straightness greater thanL/100, where L is the length of an individual chamber, when measured in accordance with 6.2.5.NOTE 4This
46、 check is to be made at the time of manufacture and is included to prevent pre-installation deformations in a chamber that meets all otherrequirements of this standard.5.3.5 Creep Rupture StrengthSpecimens fabricated in the same manner and composed of the same materials, including alladditives, as t
47、he finished chambers shall have a 50 year creep rupture tensile strength at 73 F (23 C) not less than 700 psi (4.8MPa), when determined in accordance with 6.2.6.5.3.6 Creep ModulusSpecimens fabricated in the same manner and composed of the same materials, including all additives,as the finished cham
48、bers shall have a 50 year tensile creep modulus at 73 F (23 C) not less than 24 000 psi (165 MPa) when testedat a stress level of 500 psi (3.5 MPa) or design service stress, whichever is greater. The creep modulus shall be determined inaccordance with 6.2.7. The actual test derived creep modulus sha
49、ll be used in the design of the chamber (Note 5).NOTE 5The specified minimum modulus provides assurance of long-term stiffness for a chamber resin. It does not provide assurance that all chambersmanufactured with a resin of this stiffness with be adequate for all long-term load conditions. Structural calculations to demonstrate adequacy are stillrequired in accordance with 5.5 and 5.6.2.NOTE 6The 50 year creep rupture strength and 50 year creep modulus values, determined by the test methods in 6.2.6 and 6.2.7, are used to definethe s
