ASTM F2598-2009(2017)e1 Standard Consumer Safety Specification for Clothing Storage Chests《衣柜的标准消费品安全规范》.pdf

上传人:syndromehi216 文档编号:539052 上传时间:2018-12-07 格式:PDF 页数:3 大小:64.64KB
下载 相关 举报
ASTM F2598-2009(2017)e1 Standard Consumer Safety Specification for Clothing Storage Chests《衣柜的标准消费品安全规范》.pdf_第1页
第1页 / 共3页
ASTM F2598-2009(2017)e1 Standard Consumer Safety Specification for Clothing Storage Chests《衣柜的标准消费品安全规范》.pdf_第2页
第2页 / 共3页
ASTM F2598-2009(2017)e1 Standard Consumer Safety Specification for Clothing Storage Chests《衣柜的标准消费品安全规范》.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation: F2598 09 (Reapproved 2017)1Standard Consumer Safety Specification forClothing Storage Chests1This standard is issued under the fixed designation F2598; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last r

2、evision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEEditorially updated Referenced Documents in Section 2 in June 2017.INTRODUCTIONThis consumer safety specification addresses chest a

3、ccidents that have been identified by the U.S.Consumer Product Safety Commission (CPSC).This consumer safety specification attempts to minimize the following: (1) possible entrapment andstrangulation hazards associated with sudden lid closing or dropping and (2) possible crushing,pinching, and lacer

4、ation hazards associated with folding mechanisms, hinges, and lid supports.1. Scope1.1 This consumer safety specification covers the perfor-mance requirements and test methods to ensure the safety ofchests.1.2 This consumer safety specification is intended to mini-mize the incidents and injuries to

5、children resulting fromnormal use and reasonably foreseeable misuse or abuse ofthese chests.1.3 This consumer safety specification applies to productsknown as clothes chests or other single-compartment closedrigid boxes (sometimes referred to as “cedar chests”) that aredesigned and marketed as stora

6、ge containers for clothes,blankets, or linens. The products subject to the requirementsare those with a single volume of 1.1 ft3(0.031 m3) or more.1.4 No chest produced after the approval date of thisconsumer safety specification shall, either by label or othermeans, indicate compliance with this sp

7、ecification unless itconforms to all requirements contained herein.1.5 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.6 The following

8、precautionary caveat pertains only to thetest methods portion, Section 5, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractic

9、es and determine the applicability of regulatory limita-tions prior to use.1.7 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and R

10、ecom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2F963 Consumer Safety Specification for Toy Safety2.2 ANSI Standard:3ANSI Z535.4 Product Safety Signs and Labels2.3 Federal Standard:4Title 16 Code of Federal R

11、egulations-Commercial Prac-tices16 CFR 1303 Ban on Lead-Containing Paint and CertainConsumer Products Bearing Lead-Containing Paint3. Performance Requirements3.1 Lid Support:3.1.1 Chests with vertically opening hinged lids shall beprovided with lid-support mechanisms to prevent suddencollapse or dro

12、pping of the lid.1This consumer safety specification is under the jurisdiction of ASTM Commit-tee F15 on Consumer Products and is the direct responsibility of SubcommitteeF15.42 on Furniture Safety.Current edition approved June 15, 2017. Published July 2017. Originallyapproved in 2009. Last previous

13、 edition approved in 2009 as F2598 09. DOI:10.1520/F2598-09R17E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM web

14、site.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.4Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401, http:/www.access.gpo.gov.Copyr

15、ight ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of Internatio

16、nal Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.13.1.2 The lid-support mechanism shall support the lid sothat at no position in the arc of travel of the lid from within 2.0in. (50.8 mm) of the fully closed position through

17、an arc not toexceed 60 from the fully closed position shall it drop morethan 0.50 in. (12.7 mm) under the influence of its own weight,except in the last 2.0 in. (50.8 mm) of travel. The test shall beconducted in accordance with 5.1.3.1.3 The chest lid shall comply with this requirementbefore and aft

18、er being subjected to 3500 opening and closingcycles, as described in Section 5.3.1.4 The lid-support mechanism shall not require adjust-ment by the consumer to ensure adequate lid support, nor shallit require adjustment to comply with 3.1.2 after being cycledaccording to 5.1.2.3.1.5 Lid-support mec

19、hanisms shall be designed so as toprevent pinching, crushing, or laceration injuries to fingers.Clearances or gaps produced by the action of such mechanisms(between components of the mechanism or between the mecha-nism and the chest lid) shall be constructed so that if the gapadmits a 0.19-in. (4.8-

20、mm) diameter rod it will also admit a0.50-in. (12.7-mm) diameter rod at all positions of the arc oftravel of the lid. This requirement does not apply to lid-supportmechanisms installed on the inside of the chest that are at least12 in. (305 mm) from the front and side edges of the chest orits lid.3.

21、2 ClosuresChest closures such as lids, covers, and doorsshall not be fitted with automatic locking devices.3.3 Closures and lids shall be of a type that can be openedwith a force of 10 lbf (45 N) or less when tested in accordancewith 5.2.3.4 LocksLocks shall be safety locks that do not automati-call

22、y engage.3.5 Chest shall withstand a load of 250 6 5lb(1136 2 kg)applied to the center 8 by 8-in. (20 by 20-cm) area of the lidwithout permanent damage.NOTE 1Simulating an adult sitting on top of the chest.4. Labeling4.1 The name and address (city, state, and zip code) of eitherthe manufacturer, dis

23、tributor, or seller of the chest shall eitherbe permanently and conspicuously labeled on the product orconspicuously marked in collateral information provided toeach user that includes information on assembly, proper use,safety and product care.4.2 Only those chests that meet the requirements of thi

24、ssafety specification may be marked or labeled on the product orits collateral materials with the phrase “Meets ASTM SafetySpecification F2598.”4.3 If the product does not comply with Consumer SafetySpecification F963, the chest shall be permanently and con-spicuously labeled inside on the lid with

25、the words:“WARNINGThis chest is not intended or suitable for use asa toy chest” and “Risk of Child Suffocation.” Labels shall meetthe guidelines of ANSI Z535.4.5. Test Methods5.1 Lid Support Mechanisms:5.1.1 Assemble the chest in accordance with manufacturersinstructions.5.1.2 Lift the lid to any po

26、sition in its arc of travel to adistance greater than 2.0 in. (50.8 mm) but not to cause the lidto move through an arc of more than 60 from the lids fullyclosed position measured at the outermost edge of the lid.Release the lid and observe any dropping motion of a point inthe approximate center of t

27、he outermost edge of the lid.5.1.3 Subject the lid to 3500 opening and closing cycles.One cycle consists of raising the lid from its fully closedposition to a fully open position and returning it to fully closed.5.1.4 To prevent undue stress on screws or other fastenersused to attach lid support mec

28、hanisms, take care not to forcethe lid beyond its normal arc of travel.5.1.5 Complete one cycle in approximately 10 to 15 s.Complete the 3500 cycles, then repeat the test described in5.1.2.5.2 Closures and Lids:5.2.1 Hinged LidsWith the lid in a closed position, applya gradually increasing force in

29、an upward direction perpen-dicular to the plane of the lid at a point within 1 in. (25.4 mm)from its geometric center. Note the maximum force to causethe lid to begin to open.6. General Requirements6.1 All finishes and materials used in the construction of thechests shall be nonhazardous as defined

30、by regulations underthe Federal Hazardous SubstancesAct and must conform to therequirements of the regulations for Lead in Paint under theConsumer Product Safety Act.56.2 All paints and coatings shall comply with the limitationsof antimony, arsenic, barium, cadmium, chromium, lead,mercury, and selen

31、ium as outlined in Consumer Safety Speci-fication F963.7. Keywords7.1 cedar chest; chest; clothes chest; storage chest5Regulations promulgated under these acts can be found under Title 16 of theCode of Federal Regulations.F2598 09 (2017)12ASTM International takes no position respecting the validity

32、of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject t

33、o revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.

34、 Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is

35、copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 09 (2017)13

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > ASTM

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1