1、BRITISH STANDARD AEROSPACE SERIES BS2SP 157-163:1973 (Superseding BSSP157-163) Incorporating Amendment Nos.1 and2 Specification for Solid rivets with universal head made from BS L86 (SP157 and 163), BS L58 (SP160 and 161), BSL37 (SP162) and DTD204 (SP158 and159) materials Index form of title: Rivets
2、, solid, universal head, from BS L86, BS L58, BS L37 and DTD204 materials. UDC 629.7.02:621.884.2:669.2453+629.7.02:621.884.2:669.715BS2SP157-163:1973 This BritishStandard, having been approved by the AerospaceIndustry Standards Committee, was published underthe authority of the Executive Board on 3
3、0November1973 BSI02-2000 The following BSI references relate to the work on this standard: Committee references ACE/14 Draft for approval72/35870 ISBN 0 580 07607 5 A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible f
4、or their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to6 and a back cover. This standard has been updated (see copyright date) an
5、d may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date of issue Comments 2394 November 1977 3269 July 1980 Indicated by a sideline in the marginBS2SP157-163:1973 BSI 02-2000 i Contents Page Ap
6、pendix A Recommended snap profile 4 Appendix B Rivet markings: position and dimensions 4 Appendix C Heat treatment 5 Appendix D Rivets for use in auto-riveting machines 6 Figure 1 Details of rivets 1 Figure 2 Details of snap profile 4 Figure 3 Dimensions of identification marks 5 Figure 4 Detail of
7、radiused tail 6 Table 1 Dimensions 1 Table 1A Length dimensions 2 Table 2 Material 3 Table 3 Dimensions of snap profile 4 Table 4 Dimensions of radiused tails 6ii blankBS2SP157-163:1973 BSI 02-2000 1 Table 1 Dimensions Figure 1 Details of rivets Size dash no. 24 32 40 48 56 64 80 96 Nominal diameter
8、 2.4 (0.094) 3.2 (0.126) 4.0 (0.157) 4.8 (0.189) 5.6 (0.220) 6.4 (0.250) 8.0 (0.315) 9.6 (0.378) ? A max. 2.46 (0.097) 3.25 (0.128) 4.04 (0.159) 4.83 (0.190) 5.63 (0.222) 6.43 (0.253) 8.00 (0.315) 9.60 (0.378) min. 2.36 (0.093) 3.15 (0.124) 3.94 (0.155) 4.73 (0.186) 5.53 (0.218) 6.33 (0.249) 7.90 (0
9、.311) 9.50 (0.374) ? B to theoretical sharp corners 5.0 (0.197) 6.7 (0.264) 8.3 (0.327) 10.0 (0.394) 11.7 (0.461) 13.3 (0.524) 16.7 (0.657) 20.0 (0.787) absolute minimum 4.5 (0.177) 6.0 (0.236) 7.5 (0.295) 9.0 (0.354) 10.5 (0.413) 12.1 (0.476) 15.1 (0.594) 18.1 (0.713) ? D # ? A minimum 1.80 (0.071)
10、 2.40 (0.094) 3.00 (0.118) 3.60 (0.142) 4.20 (0.165) 4.80 (0.189) 6.00 (0.236) 7.20 (0.283) C + 0.25 (0.010) 0 1.05 (0.041) 1.40 (0.055) 1.70 (0.067) 2.05 (0.081) 2.40 (0.094) 2.75 (0.108) 3.40 (0.134) 4.10 (0.161) E radius nom. 2.9 (0.114) 4.0 (0.157) 4.9 (0.193) 6.0 (0.236) 7.1 (0.280) 8.0 (0.315)
11、 10.2 (0.402) 12.3 (0.484) R radius max. 0.25 (0.010) 0.25 (0.010) 0.38 (0.015) 0.38 (0.015) 0.38 (0.015) 0.38 (0.015) 0.38 (0.015) 0.38 (0.015) min. 0.10 (0.004) 0.10 (0.004) 0.20 (0.008) 0.20 (0.008) 0.20 (0.008) 0.20 (0.008) 0.20 (0.008) 0.20 (0.008)BS2SP157-163:1973 2 BSI 02-2000 Table 1A Length
12、 dimensions NOTE 1A rounded edge from is permissible provided that it is contained within the head diameter (? B) tolerance. NOTE 2Dimensions and tolerances are in millimetres, inch conversions are in parentheses. NOTE 3When required to be cadmium coated, the dimensions of the rivets after coating m
13、ay exceed the maximum dimensions given in Table 1 and Table 1A by not more than 0.013 (0.0005). NOTE 4Remove burrs0.25(0.010) max. NOTE 5? A may increase gradually over this length to ? A max.+0.05(0.002) at point of tangency with fillet radius. NOTE 6Head to be concentric with shank within0.25(0.01
14、0) T.I.R. NOTE 7Unassigned part numbers are not to be used. NOTE 8Example of call up: NOTE 9The snap profile recommended for use with these rivets is contained in Appendix A. NOTE 10Rivets shall be packaged, bagged or labelled, and such packages, bags or labels shall bear the complete appropriate pa
15、rt number as in Note 8. NOTE 11Appendix D gives details of rivets with radiused tails for use in auto-riveting machines. Maximum available length of rivets with radiused tails is indicated thusin each size column. See Note 11.BS2SP157-163:1973 BSI 02-2000 3 Table 2 Material BS SP number Material Fin
16、ish British Standard Protective treatment Colour Identification mark (SeeAppendix B) BS SP157 a BS L86 Anodize to DEF151 Violet to DTD913 o Indented BS SP163 BS SP158 Procurement Executive M.O.D. Specification a DTD204 None oo Indented BS SP159 Cadmium coated to DTD904 BS SP160 a BS L 58 Anodize to
17、DEF151 Green + Embossed BS SP161 BS SP162 a BS L37 None o Embossed a Latest issue.BS2SP157-163:1973 4 BSI 02-2000 Appendix A Recommended snap profile Table 3 Dimensions of snap profile Appendix B Rivet markings: position and dimensions B.1 Indentification and marking B.1.1 The marking of the rivets
18、shall be as specified in Table 1, and shall be applied as follows. 1) Rivets over size24 diameter which do not exceed8 diameters in length shall be marked on the shank end with the exception of the32 diameter which may be marked on the head. 2) Size24 diameter rivets in all lengths, and rivets over
19、size24 diameter which exceed8 diameters in length may be marked on either the head or the shank end. The marking, whether indented or embossed, shall be clearly visible, and height or depth shall not exceed the following dimensions. 0.006 in on sizes up to and including size32 diameter; 0.008 in on
20、sizes40 and48 diameter; 0.010 in on sizes56 diameter and over. Rivet size dash no. Depth of cupping, A 0.05 Cupping flat, B 0.25 Radius of cupping, R (nom.) 24 mm 0.72 mm 2.95 mm 3.3 32 1.15 3.80 4.4 40 1.24 4.65 5.3 48 1.47 5.50 6.4 56 1.76 6.10 7.5 64 2.00 7.10 8.4 80 2.56 8.60 10.6 96 3.20 10.20
21、12.7 Figure 2 Details of snap profileBS2SP157-163:1973 BSI 02-2000 5 B.1.2 The rivets shall be identified for ordering purposes by the relevant part number. (See Note8.) Appendix C Heat treatment C.1 BS SP157, BS SP163 BS L86 Material Rivets to BS SP157 and BS SP163 shall be heat treated by the rive
22、t manufacturer as follows. Solution treat at a temperature of495 5 C and quench in water at a temperature not exceeding40 C. Age at room temperature for not less than four days. C.2 BS SP162 BS L37 Material C.2.1 Immediately before use or before refrigeration as described below, rivets to BS SP162 s
23、hall be heated uniformly at a temperature of495 5 C and quenched in water at a temperature not exceeding40 C. C.2.2 Rivets to BS SP162 commence to age harden immediately when kept at atmospheric temperature after quenching. Ageing may be delayed, however, by storing the rivets at low temperatures af
24、ter quenching, and they may be expected to remain in a condition suitable for closing for a period depending on the storage temperature as shown below: The rivets shall be closed within two hours of solution treatment if kept at atmospheric temperature or within two hours of removal from cold storag
25、e. C.3 BS SP160, BS SP161 BS L58 Material Rivets in L58 material do not require heat treatment. C.4 BS SP158, BS SP159 DTD204 Material Rivets in DTD204 material do not require heat treatment. Figure 3 Dimensions of identification marks Temperature Maximum storage period 0 C to5 C 15 C to20 C 45hours
26、 150hoursBS2SP157-163:1973 6 BSI 02-2000 Appendix D Rivets for use in auto-riveting machines D.1 With the advent of auto-riveting machines, it is necessary to form the rivet tail with a small radius. Conventional methods of riveting are unaffected by this feature. Table 4 Dimensions of radiused tail
27、s D.2 Rivets of standard lengths and diameters, up to the maximum available lengths indicated thusas shown in Table 1A, may be supplied with radius tails on request. The method of call-up is given in Note8. D.3 Text deleted Figure 4 Detail of radiused tail Nominal diameter S min. T rad. 0.25in. (0.0
28、10) Dia. P max. mm (in) mm (in) mm (in) mm (in) 2.4 (0.094) 0.46 (0.018) 0.74 (0.029) 1.98 (0.078) 3.2 (0.126) 0.66 (0.026) 0.98 (0.039) 2.59 (0.102) 4.0 (0.157) 0.86 (0.034) 1.24 (0.049) 3.25 (0.128) 4.8 (0.189) 1.07 (0.042) 1.50 (0.059) 3.89 (0.153) 5.6 (0.220) 1.24 (0.049) 1.75 (0.069) 4.60 (0.18
29、0) 6.4 (0.250) 1.45 (0.057) 1.98 (0.078) 5.13 (0.202) 8.0 (0.315) 1.86 (0.073) 2.50 (0.098) 6.30 (0.248) 9.6 (0.378) 2.26 (0.089) 2.97 (0.117) 7.47 (0.294)blankBS2SP 157-163:1973 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible
30、for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or e
31、ditions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the
32、inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be a
33、ddressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range
34、of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:0
35、2089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in al
36、l BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means el
37、ectronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
