1、BRITISH STANDARD BS4193-17: 1989 ISO7406:1986 Hardmetal insert tooling Part 17: Specification for designation of bore type milling cutters for indexable inserts ISO title: Bore type milling cutters for indexable inserts Designation UDC 621.9.025.7182.8BS4193-17:1989 This British Standard, having bee
2、n prepared under the directionof the Machine, Engineers and Hand Tools Standards Committee, was published under the authority ofthe Board of BSI and comesintoeffect on 31January1989 BSI10-1999 The following BSI references relate to the work on this standard: Committee reference MTE/18 Draft for comm
3、ent83/79266 DC ISBN 0 580 17063 2 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Machine, Engineers and Hand Tools Standards Committee (MTE/-) to Technical Committee MTE/18 upon which the following bodies were represented: Advanced Manu
4、facturing Technology Research Institute British Hardmetal Association High Speed Steel Tool Bit Association Society of British Aerospace Companies Limited Welding Manufacturers Association (BEAMA Ltd.) Coopted members Amendments issued since publication Amd. No. Date of issue CommentsBS4193-17:1989
5、BSI 10-1999 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope and field of application 1 2 References 1 3 Explanation of the code 1 4 Symbols 2 Publications referred to Inside back coverBS4193-17:1989 ii BSI 10-1999 National foreword This Part of BS4193 has been
6、prepared under the direction of the Machine, Engineers and Hand Tools Standards Committee and forms part of a series, each Part dealing with an aspect of hardmetal insert tooling. The series implements corresponding International Standards in the development of which the UK has played an active part
7、. This Part of BS4193 is identical with ISO7406 “Bore type milling cutters for indexable inserts Designation” which was published in1986 by the International Organization for Standardization (ISO) and was prepared by Technical Committee ISO/TC29, Small tools. Terminology and conventions. The text of
8、 the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is drawn especially to the following. The comma has been used as a decimal mar
9、ker. In British Standards it is current practice to use a full point on the baseline as the decimal marker. Wherever the words “International Standard” appear, referring to this standard, they should be read as “Part of BS4193”. The Technical Committee has reviewed the provisions of ISO3002-1:1982 t
10、o which reference is made in the text and has decided that they are acceptable for use in conjunction with this standard. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance wi
11、th a British Standard does not of itself confer immunity from legal obligations. Cross-references International Standard Corresponding British Standard BS4193 Hardmetal insert tooling ISO1832:1985 Part1:1986 Specification for designation of indexable inserts for cutting tools (Identical) ISO6462:198
12、3 Part11:1983 Specification for dimensions of face milling cutters with indexable inserts (Identical) ISO6986:1983 Part12:1984 Specification for dimensions of side and face milling and slotting cutters with indexable inserts (Identical) ISO7848:1986 Part16:1986 Specification for designation of shank
13、 type milling cutters for indexable inserts (Identical) Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This w
14、ill be indicated in the amendment table on the inside front cover.BS4193-17:1989 BSI 10-1999 1 1 Scope and field of application This International Standard establishes a code for the designation of bore type milling cutters intended for indexable inserts, with the purpose of simplifying orders and s
15、pecifications for such tools. It covers the designation of face milling cutters, side and face (slotting) milling cutters, shell end mills as well as simple designs of slab milling cutters. 2 References ISO1832, Indexable (throwaway) inserts fur cutting tools Designation Code of symbolization. ISO30
16、02-1, Basic quantities in cutting and grinding Part1: Geometry of the active part of cutting tools General terms, reference systems, tool and working angles, chip breakers. ISO6462, Face milling cutters with indexable inserts Dimensions. ISO6986, Side and face milling (slotting) cutters with indexab
17、le inserts Dimensions. ISO7848, Shank type milling cutters for indexable inserts Designation. 3 Explanation of the code The code consists of eleven symbols of which the first ten symbols shall be used in any designation. The last symbol shall be used only for side and face (slotting) milling cutters
18、, shell end mills and slab milling cutters. Four symbols designate the characteristics of the body and seven the clamping and characteristics of the inserts. In addition to the standardized designation (symbols e to o), a supplementary symbolp consisting of a maximum of two letters and/or numbers ma
19、y be added by the manufacturer after the standardized designation for a better description of his products, subject to this symbol being separated from the standardized designation by a dash. No addition to or extension of the code given in this International Standard shall be made without consultat
20、ion with technical committee ISO/TC29 and its agreement. Rather than adding symbols not provided for in this system, it is preferable to add to the designation conforming to this International Standard any necessary explanations in detailed sketches or specifications. The meaning of the eleven symbo
21、ls constituting the code is as follows: Examples: Face milling cutter: e Number symbol identifying the cutter diameter (see4.1). Symbols for the characteristics of the body f Letter symbol identifying the type of cutter and the type and/or size of the attachment (see4.2). g Number symbol identifying
22、 the number of slots (see4.3). h Letter symbol identifying cutting direction (see4.4). Dash (not counted as a symbol). i Letter symbol identifying the method of holding the insert (see4.5). Symbols for clamping and characteristics of the inserts j Number symbol identifying insert cutting edge angle
23、(see4.6). k Letter symbol identifying the insert shape (see4.7). l Letter symbol identifying the normal clearance of insert (see4.8). m Number symbol identifying the indexable insert size (see4.9). n Letter symbol identifying the normal clearance of the wiper edge (see4.10). o Number symbol identify
24、ing the cutting width of side and face milling cutters or of slab milling cutters (see4.11). p Symbol for the manufacturer, at his option. e f g h i j k l m n 250C C 20 R W 75 S N 12 P BS4193-17:1989 2 BSI 10-1999 Side and face milling (slotting) cutter: 4 Symbols 4.1 Symbol for the cutter diameter
25、Referencee The number symbol for the cutter diameter is a two- or three-digit number equal to the cutting diameter in millimetres. 4.2 Symbol for the type of cutter and for the type and/or size of the attachment Referencef 4.3 Symbol for the number of slots Referenceg The number symbol is also the n
26、umber of slots. NOTEDefined here is the effective number of slots used to determine feed speed. It does not always correspond to the real total number of slots on the tool, because of the staggered disposition of the inserts on the milling cutter. One-digit values are to be preceded by0 (zero); for
27、example for eight slots, the symbol is08. e f g h i j k l m n o 160 H 18 N F 90 T P 16 P 20 Letter symbol Type and/or size of the attachment Type of cutter A Tenon drive, hexagon socket head cap screw (type A in ISO6462) B Tenon drive, cutter retaining screw (type B of ISO6462) C Centring arbor havi
28、ng a7/24 taper (type C in ISO6462) X Special designs E Bore diameter22mm F Bore diameter27mm G Bore diameter32mm H Bore diameter40mm J Bore diameter50mm K Bore diameter60mm M Bore diameter80mm N Bore diameter100mm Y Special designs T Tenon drive U Key driveBS4193-17:1989 BSI 10-1999 3 4.4 Symbol for
29、 the cutting direction of the cutter Referenceh 4.5 Symbol for the method of holding the insert Referencei 4.6 Symbol for the insert cutting edge angle Referencej The symbol is the angle expressed in degrees; see also ISO1832. For round inserts with the diameter converted from an inch value, symbolj
30、 is00; for round inserts with metric diameter, it isM0. Letter symbol Type of cutter Direction of cut R Face milling cutters, side and face milling cutters with straight teeth and shell end mills Right hand L Left hand N Side and face milling cutters with staggered teeth (for slotting) and slab mill
31、ing cutters Either side (neutral) Letter symbol Method of holding Insert Figure C Top clamping Without hole M Top and hole clamping With cylindrical hole P Hole clamping With cylindrical hole S Screw clamping through hole With partly cylindrical hole W Wedge type clamping behind the insert Any F Wed
32、ge type clamping in front of the insert Any K Cartridge with insert Any X Special designs Any BS4193-17:1989 4 BSI 10-1999 4.7 Symbol for the insert shape Referencek If the milling cutter is equipped with inserts of different shapes, the symbol for the insert shape shall be X. 4.8 Symbol for the nor
33、mal clearance of insert Referencel If the milling cutter is equipped with inserts having different normal clearances, the symbol for the normal clearance shall be X. Letter symbol Insert shape Insert type H O P S T Hexagonal Octagonal Pentagonal Square Triangular Equilateral and equiangular C D E M
34、V W Rhombic with80 included angle Rhombic with55 included angle Rhombic with75 included angle Rhombic with86 included angle Rhombic with35 included angle Hexagonal with80 included angle Equilateral but non-equiangular L Rectangular Non-equilateral but equiangular A B K Parallelogram-shaped with85 in
35、cluded angle Parallelogram-shaped with82 included angle Parallelogram-shaped with55 included angle Non-equilateral and non-equiangular R Round Round NOTEThe included angle is always the smaller angle. Letter symbol Insert normal clearance A B C D E F G N P 3 5 7 15 20 25 30 0 11 NOTEFor non-equilate
36、ral inserts, the symbol applies to the normal clearance of the longer side.BS4193-17:1989 BSI 10-1999 5 4.9 Symbol for the indexable insert size Referencem If the milling cutter is equipped with inserts having different sizes, the symbol for the insert size shall be XX. 4.10 Symbol for the normal cl
37、earance of the wiper edge of the insert Referencen If the milling cutter is equipped with inserts having different wiper normal clearances, the wiper symbol shall be X. NOTEFor milling cutters designed to receive indexable inserts without wiper edges (e.g.milling cutters with round inserts), referen
38、cen is not used. However, if referenceo has to be specified by a symbol, referencen will be represented by a dash (). 4.11 Symbol for the cutting width of side and face (slotting) milling cutters, shell end mills and slab milling cutters Referenceo The number symbol is a two- or three-digit number e
39、qual to the nominal cutting width in millimetres (disregarding any decimals) of side and face (slotting) milling cutters, shell end mills and of slab milling cutters. For cutting widths smaller than10mm, the first digit shall be0 (zero). Example: NOTEThe possibility of adjusting the cutting width of
40、 side and face milling cutters shall be indicated in the catalogues for these tools. The nominal width is in this case the mean value of the adjusting range. Insert type Number symbol Equilateral and equiangular (H, O, P, S, T) and equilateral and non-equiangular (C, D, E, M, V, W) The designation s
41、ymbol for the insert size is the side length, disregarding any decimals. Example: Edge length: 16,5mm Symbol of designation: 16 Non-equilateral and equiangular (L) and non-equilateral and non-equiangular (A, B, K) The designation symbol for the insert size is always given for the major or the longer
42、 cutting edge. The designation symbol is the length, disregarding any decimals. Example: Length of the major cutting edge: 19,5mm Symbol of designation: 19 Round insert (R) The designation symbol for the insert size is always given for the diameter value disregarding any decimals. Example: Diameter:
43、 15,875mm Symbol of designation: 15 NOTEWhen the symbol resulting from the value has only one digit, it shall be preceded by0 (zero). Example: Cutting edge length: Symbol of designation: 9,525mm 09 Letter symbol Normal clearance of the wiper edge A B C D E F G N P 3 5 7 15 20 25 30 0 11 Cutting widt
44、h: 8mm Symbol of designation: 086 blankBS4193-17:1989 BSI 10-1999 Publications referred to See national foreword.BS4193-17: 1989 ISO7406:1986 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It pr
45、esents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BS
46、I to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000.
47、Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02
48、089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European
49、and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other
