BS 5760-13 5-1996 Reliability of systems equipment and components - Guide to reliability test conditions for consumer equipment - Ground mobile equipment - Low degree of simulation.pdf

相关资源

BS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdf

BS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdf

BS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdf

BS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdf

BS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf

BS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdf

BS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdf

BS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdf

BS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdf

BS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdf

猜你喜欢

STAS 9128-1980 TWIST DRILL WITH TAPER SHANK WITH CARBIDE TIP Dimensions《硬质合金刀头的锥形柄麻花钻 尺寸 》.pdf

STAS 9129-1980 TWIST DRILL WITH PARALLEL SHANK WITH CARBIDE TIP Dimensions《硬质合金刀头的平行柄麻花钻 尺寸 》.pdf

STAS 9130 1-1989 Cutting carbide tips for tools FRITTED HARDMETAL INDEXABLE CARBIDE TIPS WITH ROUNDED CORNER WITHOUT FIXING HOLE Dimensions《工具用的硬质合金刀头 多孔硬质合金圆角无固定孔可转位得硬质合金刀头仍 尺寸 》.pdf

STAS 9130 2-1989 Cutting carbide tips for tools FRITTED HARDMETAL INDE- XABLE CARBIDE TIPS WITH ROUNDED CORNER WITH CY- LINDRICAL FIXING HOLE Dimensions《工具用的硬质合金刀头多孔 硬质合金 柱状固定孔圆角硬质.pdf

STAS 9130 3-1989 Inserts for cutting tools INDEXABLE CARBIDE HARD METAL INSERTS WITH WIPER EDGES WITHOUT FIXING HOLE Dimensions《刀削工具用的刀片 带有滑动边缘无固定孔的可转位的碳化物硬质合金刀片尺寸 》.pdf

STAS 9130 4-1989 Boring tips for tools INDEXABLE HARDMETAL CAR- BIDE INSERTS WITH ROUNDED CORNERS WITSH CYLINDRICAL FIMNG HOLE AND INSERTS WITH an = 7 degrees normal clearance Dime.pdf

STAS 9130 5-1989 Cutting carbide tips for tools FRITTED HARDMETAL INDEXABLE CARBIDE TIPS WITH CHIP-BREAKER ON BOTH SIDES WITHOUT BORE Dimensions《工具用硬质合金刀头 无膛两面都带断屑台的多孔硬质合金硬质合金刀头 尺寸.pdf

STAS 9130 6-1989 Indexable inserts for culling tools lNDKXABI.K INSERTS Designation《剔出工具用的可转位的刀片 可转位 刀片标识 》.pdf

STAS 9131 1-1972 LEAD ALLOYS FOR STORAGE BATTERIES General directions for carrying out chemical analysis《蓄电池用的铅合金 进行化学分析的一般方向 》.pdf