1、BRITISH STANDARD BS AU 207:1986 Specification for Dimensions of car radio installation space UDC 629.113.051:621.396.62.005BSAU207:1986 This BritishStandard, having been prepared under the directionof the Automobile Standards Committee, was published under the authority ofthe Board of BSI and comes
2、intoeffect on 31December1986 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference AUE/9 Draft for comment81/78343 DC ISBN 0 580 15347 9 Committees responsible for this BritishStandard The preparation of this BritishStandard was entrusted by the Automobile
3、 Standards Committee (AUE/-) to Technical Committee AUE/9, upon which the following bodies were represented: Automobile Association British Friction Materials Council Consumer Standards Advisory Committee of BSI Department of Trade and Industry (Consumer Safety Unit, C S Division) Department of Tran
4、sport (Highways) Garage Equipment Association Health and Safety Executive Home Office Institute of Trading Standards Administration Motor Agents Association Limited Motor Cycle Association of Great Britain Petrol Pump Manufacturers Association Royal Automobile Club Society of Motor Manufacturers and
5、 Traders Limited Amendments issued since publication Amd. No. Date of issue CommentsBSAU207:1986 BSI 02-2000 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Dimensions of installation space and fixing areas 1 3 Dimensions and position of port 1 Appendix A Recommenda
6、tions for installation 3 Figure 1 Dimensions for installation by front fixing 1 Figure 2 Dimensions for installation by lateral fixing 1 Figure 3 Dimensions for installation by additional rear fixing and for a port 2 Publication referred to Inside back coverBSAU207:1986 ii BSI 02-2000 Foreword BS AU
7、207 was prepared under the direction of the Automobile Standards Committee. It is similar to but not identical with ISO7736 “Road vehicles Car radio for front installation Installation space including connections”, published by the International Organization for Standardization (ISO). Changes have b
8、een made to Figure 1 and Figure 2 of that International Standard to permit fitment of some existing car radios and future equipment. The minimum lateral fixing installation dimension has been increased from188mm minimum to189.5mm minimum. The radius “R3max.” in the International Standard has been am
9、ended to “R4max.”. The dimension“5 1” in the International Standard has been changed to“5.5 0.5”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard do
10、es not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This
11、will be indicated in the amendment table on the inside front cover.BSAU207:1986 BSI 02-2000 1 1 Scope This BritishStandard specifies the dimensions for the installation space and fixing areas required by car radio equipment and its electrical connections, including car radio equipment which is combi
12、ned with other sound reproduction equipment. General recommendations for installation spaces are given in Appendix A. 2 Dimensions of installation space and fixing areas 2.1 The dimensions for installation by front fixing shall be as shown in Figure 1. 2.2 The dimensions for installation by lateral
13、fixing shall be as shown in Figure 2. NOTEFront fixing or lateral fixing or a combination of front and lateral fixing may be used. 2.3 The dimensions for installation by additional rear fixing shall be as shown in Figure 3. NOTERear fixing may be provided in addition to the front and lateral fixings
14、 3 Dimensions and position of port If a port is provided, it shall be positioned and its dimensions shall be as shown in Figure 3. Figure 1 Dimensions for installation by front fixing Figure 2 Dimensions for installation by lateral fixingBSAU207:1986 2 BSI 02-2000 Figure 3 Dimensions for installati
15、on by additional rear fixing and for a portBSAU207:1986 BSI 02-2000 3 Appendix A Recommendations for installation A.1 The space should be planned so that the car radio is easily visible and within hand reach of the driver. A.2 It is recommended that the planned installation angle is not more than45
16、from the horizontal where the rear of the car radio slopes downward. A.3 In particular, ventilation of the space reserved for the car radio is recommended. Heating of the car radio due to the proximity of the heating system has to be avoided. A.4 All holes and apertures have to be free from sharp ed
17、ges to minimize the risk of injury during installation.4 blankBSAU207:1986 BSI 02-2000 Publication referred to ISO7736, Road vehicles Car radio for front installation Installation space including connections 1) . 1) Referred to in the foreword only.BS AU 207:1986 BSI 389 Chiswick High Road London W4
18、 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Us
19、ers of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secreta
20、ry of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying stand
21、ards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStand
22、ards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on
23、all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership
24、 Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be r
25、eproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and si
26、ze, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
