1、BRITISH STANDARD AEROSPACE SERIES BS EN 2555:1993 Rivets, solid,100normal countersunk head with dome, in aluminium alloy5056A, inch based series The European StandardEN2555:1992 has the status of a British Standard UDC 629.7:621.884.091.6-034.71BSEN2555:1993 This British Standard, having been prepar
2、ed under the directionof the Aerospace Standards Policy Committee, waspublished under theauthorityof the StandardsBoardand comesintoeffect on 15 February1993 BSI 11-1999 The following BSI references relate to the work on this standard: Committee reference ACE/12 Draft for comment89/79439 DC ISBN 0 5
3、80 21981 X Cooperating organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalis
4、ation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland Ireland National Standards Authority
5、of Ireland Italy Ente Nazionale Italiano di Unificazione Luxembourg Inspection du Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Asociacin Espaola de Normalizacin y Certificacin Sweden Standardis
6、eringskommissionen i Sverige Switzerland Association suisse de normalisation UnitedKingdom British Standards Institution Amendments issued since publication Amd. No. Date CommentsBSEN2555:1993 BSI 11-1999 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 1
7、Scope 3 2 Normative references 3 3 Required characteristics 3 4 Designation 6 5 Marking 6 6 Technical specification 6 National annex NA (informative) Committees responsible Inside back cover National annex NB (informative) Cross-references Inside back cover Figure 1 4 Figure 2 6 Table 1 4 Table 2 5
8、Table 3 6BSEN2555:1993 ii BSI 11-1999 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version ofEN2555:1992 Aerospace series Rivets, solid,100 normal countersunk head with dome, in aluminium alloy50
9、56A, inch based series, published by the European Committee for Standardization (CEN). EN2555:1992 was produced as a result of international discussions in which the UnitedKingdom took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of
10、 British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 6, an inside bac
11、k cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN2555 November 1992 UDC629.7:621.884.091.6-034.71 Descrip
12、tors: Aircraft industry, full rivet, countersunk head rivet, aluminium alloy, dimension, designation, marking English version Aerospace series Rivets, solid,100 normal countersunk head with dome, in aluminium alloy5056A, inch based series Srie arospatiale Rivets ordinaires, tte fraise100 normale ave
13、c dme, en alliage daluminium5056A, srie base inches Luft- und Raumfahrt Vollniete, mit100 normalem Senkkopf mit Dom, aus Aluminiumlegierung5056A, Inch-Reihe This European Standard was approved by CEN on1992-11-16. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipul
14、ate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exi
15、sts in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bo
16、dies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secr
17、etariat: rue de Stassart 36, B-1050 Brussels 1992 Copyright reserved to CEN members Ref. No. EN2555:1992 EEN2555:1992 BSI 11-1999 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance wi
18、th the rules of this Association, this standard has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publica
19、tion of an identical text or by endorsement, at the latest byMay1993, and conflicting national standards shall be withdrawn at the latest byMay1993. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Fi
20、nland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the UnitedKingdom.EN2555:1992 BSI 11-1999 3 1 Scope This standard specifies the characteristics of solid rivets, with100 normal countersunk head with dome, inch based se
21、ries, in aluminium alloy, for maximum operating temperature120 C. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed h
22、ereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 2000, Aerospace series Qualit
23、y assurance EN aerospace products Approval of the quality system of manufacturers. EN 2117, Aerospace series Aluminium alloy5056A-H32 wire for solid rivets Dk 10mm 1) . EN 2345, Aluminium and aluminium alloy rivets Technical specification Aerospace series 1) . EN 2424, Aerospace series Identificatio
24、n marking of standard fasteners 1) . 3 Required characteristics 3.1 Configuration Dimensions Masses SeeFigure 1 andTable 1 andTable 2. Dimensions and tolerances are expressed in millimetres. 3.2 Material EN 2117 The rivet shall be delivered in H32 condition. 1) Published as AECMA standard at the dat
25、e of publication of the present standardEN2555:1992 4 BSI 11-1999 Table 1 1) The length range is limited (seeTable 2). 2) Shape optional (except concave) within limiting dimensions 3) Blended convex form permissible within limiting dimensions Figure 1 Diameter code D 1 a D 2 b D 3 D 4 D 5 D 6 H 1 H
26、2 H 3 L 2 L 3 R max. min. min. max. min. max. min. min. max. min. max. min. 0,08 016 1,65 1,55 3 2,65 2,4 1,6 2,46 0,6 0,03 0,33 0,25 2,1 024 2,45 2,35 4,65 4,2 3,6 2,4 3,84 1,9 1,6 0,9 0,05 0,44 0,36 2,4 0,8 0,5 0,15 032 3,25 3,15 5,8 5,3 4,8 3,2 4,88 2,6 2,3 1,1 0,06 0,49 0,41 2,6 1 0,7 040 4,05 3
27、,94 7,35 6,8 6 4 6,17 3,2 2,8 1,4 0,08 0,6 0,52 3 1,2 0,8 048 4,85 4,73 9,05 8,4 7,2 4,8 7,57 3,8 3,3 1,8 0,72 0,64 3,8 1,5 1 0,25 056 5,65 5,33 10,65 10.1 8,4 5,6 8,89 4,5 3,9 2,1 0,84 0,76 4,1 1,8 1,2 a D 1max may increase by 0,03, over length (L 2 H 1 ). b Maximum conditionEN 2555:1992 BSI 11-199
28、9 5 Table 2 Diameter code 016 024 032 040 048 056 Length a Mass b a Mass b a Mass b a Mass b a Mass b a Mass b kg/1000 pieces kg/1000 pieces kg/1000 pieces kg/1000 pieces kg/1000 pieces kg/1000 pieces Code L 1 N R N R N R N R N R N R 003 3 0,026 004 4 0,032 0,080 0,147 005 5 0,038 0,093 0,170 006 6
29、0,044 0,106 0,193 0,323 007 7 0,050 0,119 0,216 0,358 008 8 0,056 0,132 0,239 0,394 0,615 009 9 0,062 0,145 0,261 0,430 0,666 010 10 0,067 0,158 0,284 0,465 0,717 1,020 011 11 0,073 0,171 0,307 0,500 0,768 1,089 012 12 0,079 0,184 0,330 0,536 0,819 1,158 014 14 0,091 0,210 0,376 0,607 0,921 1,296 01
30、6 16 0,103 0,236 0,422 0,678 1,023 1,434 018 18 0,262 0,467 0,750 1,125 1,572 020 20 0,288 0,513 0,820 1,227 1,710 022 22 0,314 0,559 0,891 1,329 1,848 024 24 0,340 0,605 0,962 1,431 1,986 026 26 0,366 0,651 1,033 1,533 2,124 028 28 0,392 0,696 1,105 1,635 2,262 030 30 0,418 0,742 1,176 1,737 2,400
31、032 32 0,444 0,788 1,247 1,839 2,538 035 35 0,483 0,856 1,353 1,992 2,745 040 40 0,971 1,531 2,247 3,090 045 45 1,085 1,709 2,502 3,435 050 50 1,886 2,757 3,780 055 55 3,012 4,125 060 60 3,267 4,470 a Tail end code (seeFigure 1) b Approximate values, calculated on the basis, of2,76kg/dm 3 , given fo
32、r information purpose only + 0,5 0EN2555:1992 6 BSI 11-1999 4 Designation Example: NOTEIf necessary, the originator code19005 shall be placed between the description block and the identity block. 5 Marking 5.1 Rivet identification EN2424, style G 5.2 Material identification SeeFigure 2 andTable 3. S
33、ymbol at manufacturers option Table 3 6 Technical specification EN2345 except for approval of manufacturers, seeEN2000. Figure 2 Diameter code 016 024 032 040 048 056 T 0,05 0,13 0,15 S max. 0,8 D 7max. D 1max. (seeTable 1)BSEN2555:1993 BSI 11-1999 National annex NA (informative) Committees responsi
34、ble The UnitedKingdom participation in the preparation of this European Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/12, upon which the following bodies were represented: Association of Electronics, Telecommunications and Business Equipment In
35、dustries British Industrial Fasteners Federation Ministry of Defence Society of British Aerospace Companies Ltd. National annex NB (informative) Cross-references The British Standards corresponding to the European Standards referred to in the text are identical in number and title with those given i
36、nclause2, with the exception ofEN2117, EN2345 and EN2424 for which no corresponding British Standards exist.BS EN 2555:1993 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view
37、 on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the q
38、uality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. B
39、SI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:020
40、89967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international
41、standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to d
42、ate with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in th
43、e UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without
44、prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
