1、BRITISH STANDARDBS EN 725-9:2006Advanced technical ceramics Methods of test for ceramic powders Part 9: Determination of un-tapped bulk densityThe European Standard EN 725-9:2006 has the status of a British StandardICS 81.060.30g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g
2、53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Mon May 15 06:44:28 BST 2006, Uncontrolled Copy, (c) BSIBS EN 725-9:2006This British Standard was published under the authority of the Standard
3、s Policy and Strategy Committee on 16 March 2006 BSI 16 March 2006ISBN 0 580 47964 1National forewordThis British Standard is the official English language version of EN 725-9:2006. It supersedes BS EN 725-9:1997 which is withdrawn.The UK participation in its preparation was entrusted to Technical C
4、ommittee RPI/13, Advanced technical ceramics, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document m
5、ay be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users
6、are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, a
7、nd keep UK interests informed; monitor related international and European developments and promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and a back cover.The BSI copyright notice displayed in this document indi
8、cates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsLicensed Copy: Wang Bin, na, Mon May 15 06:44:28 BST 2006, Uncontrolled Copy, (c) BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 725-9March 2006ICS 81.060.30 Supersedes EN 725-9:1997 English Versio
9、nAdvanced technical ceramics - Methods of test for ceramicpowders - Part 9: Determination of un-tapped bulk densityCramiques techniques avances - Mthodes dessai pourpoudres cramiques - Partie 9: Dtermination de la massevolumique en vracHochleistungskeramik - Prfverfahren fr keramischePulver - Teil 9
10、: Bestimmung der SchttdichteThis European Standard was approved by CEN on 3 February 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lis
11、ts and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsi
12、bility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, It
13、aly, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050
14、Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 725-9:2006: ELicensed Copy: Wang Bin, na, Mon May 15 06:44:28 BST 2006, Uncontrolled Copy, (c) BSIEN 725-9:2006 (E) 2 Contents Page Foreword.3 1 Scope5 2 Normative referen
15、ces5 3 Principle .5 4 Apparatus.5 5 Procedure.5 5.1 Sample treatment 5 5.2 Measurement .6 6 Expression of results 6 7 Test report6 Annex A (informative) Repeatability and reproducibility .9 Licensed Copy: Wang Bin, na, Mon May 15 06:44:28 BST 2006, Uncontrolled Copy, (c) BSIEN 725-9:2006 (E) 3 Forew
16、ord This European Standard (EN 725-9:2006) has been prepared by Technical Committee CEN/TC 184 “Advanced technical ceramics”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement
17、, at the latest by September 2006, and conflicting national standards shall be withdrawn at the latest by September 2006. This European Standard supersedes EN 725-9:1997. The main changes in the new edition are: - revision of the Foreword to reflect changes in the EN 725 series; - addition of normat
18、ive references; - modifications to the apparatus specification; - modifications to the test report requirements. EN 725 Advanced technical ceramics Methods of test for ceramic powders was prepared in Parts as follows: Part 1 Determination of impurities in alumina Part 2 Determination of impurities i
19、n barium titanate Part 3 Determination of oxygen content of non-oxides by thermal extraction with a carrier gas Part 4 Determination of oxygen content in aluminium nitride by XRF analysis Part 5 Determination of particle size distribution Part 6 Determination of specific surface area withdrawn Part
20、7 Determination of absolute density withdrawn Part 8 Determination of tapped bulk density Part 9 Determination of un-tapped bulk density Part 10 Determination of compaction properties Part 11 Determination of densification on natural sintering Part 12 Chemical analysis of zirconia Parts 6 and 7 of t
21、he series were superseded in 2005 by EN ISO 18757 and EN ISO 18753 respectively. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Licensed Copy: Wang Bin,
22、na, Mon May 15 06:44:28 BST 2006, Uncontrolled Copy, (c) BSIEN 725-9:2006 (E) 4 Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Swi
23、tzerland and United Kingdom. Licensed Copy: Wang Bin, na, Mon May 15 06:44:28 BST 2006, Uncontrolled Copy, (c) BSIEN 725-9:2006 (E) 5 1 Scope This European Standard specifies a method for the determination of the un-tapped bulk density of granulated or un-granulated ceramic powders. 2 Normative refe
24、rences The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO/IEC 17025, General require
25、ments for the competence of testing and calibration laboratories (ISO/IEC 17025:2005) ISO 565, Test sieves Metal wire cloth, perforated metal plate and electroformed sheet Nominal sizes of openings 3 Principle The mass of a known volume of the powder is determined after allowing it to fall freely in
26、to a stationary container, avoiding vibration. The un-tapped bulk density is expressed by division of this mass by the volume of the container. 4 Apparatus 4.1 Stainless steel cylindrical container (see Figure 1) of volume approximately 100 cm3and a diameter to height ratio in the range 0,9 to 1,1.
27、The exact volume of the container shall be measured to the nearest 0,2 cm3. 4.2 Sieve, with an aperture size of 710 m as specified in ISO 565 and with a typical diameter of 80 mm. 4.3 Balance with a resolution of 0,01 g. 4.4 Tray, to collect the powder during the filling of the container. 4.5 Suitab
28、le assembly for allowing the powder to flow and fill the container (4.1) evenly, including a fixing system for the sieve (4.2) with a cone in its lower part to allow the sieve and the cone to be set to a predetermined height above the top level of the container, and a system to regulate the vibratio
29、n of the sieve (see Figure 1). 5 Procedure 5.1 Sample treatment If there is any treatment of the sample before measurement (e.g. drying), this shall be recorded in the test report. Licensed Copy: Wang Bin, na, Mon May 15 06:44:28 BST 2006, Uncontrolled Copy, (c) BSIEN 725-9:2006 (E) 6 5.2 Measuremen
30、t Weigh the cylindrical container (4.1). Set the cylindrical container in the tray (4.4) so that its axis coincides with that of the cone, with the level of the sieve at a height of 190 mm above the cylindrical container top. Fill the sieve with the sample. If necessary start the vibration system (4
31、.5) and regulate it to allow the powder to flow evenly. Fill the cylindrical container in between 20 s and 30 s. Stop the feed when the powder has formed a cone above the top of the cylindrical container and is spilling over. Remove the cone of surplus powder by gently drawing a straight edge across
32、 the top rim of the cylindrical container, without communicating any vibration to the latter. Weigh the cylindrical container and its contents. 6 Expression of results The un-tapped bulk density bis given by the following equation: 10bmmV= (1) where m0is the mass, in grams, of the empty cylindrical
33、container; m1is the mass, in grams, of the cylindrical container full of powder; V is the volume, in cubic centimetres, of the cylindrical container. Calculate the density in grams per cubic centimetre and then convert the answer to kilograms per cubic metre, to the nearest 5 kg/m3. Information on t
34、he probable repeatability and reproducibility of results is given in Annex A. 7 Test report The test report shall be in accordance with the reporting provisions of EN ISO/IEC 17025, and shall include at least the following information: a) name and address of the testing establishment; b) date of the
35、 test; c) on each page, a unique report identification and page number; d) customer name and address; e) reference to this European Standard, i.e. determined in accordance with EN 725-9; f) authorising signature; g) any deviation from the method described, with appropriate validation, i.e. demonstra
36、ted to be acceptable to the parties involved; h) description of the powder (e.g. material type, manufacturer code, batch or code number); Licensed Copy: Wang Bin, na, Mon May 15 06:44:28 BST 2006, Uncontrolled Copy, (c) BSIEN 725-9:2006 (E) 7 i) any pre-treatment of the powder such as drying; j) res
37、ults; k) any unusual features noted during the determination; l) any comments about the test or test results. Licensed Copy: Wang Bin, na, Mon May 15 06:44:28 BST 2006, Uncontrolled Copy, (c) BSIEN 725-9:2006 (E) 8 Dimensions in millimetres 75506519055502341Key 1 710 m sieve 3 Stainless steel cylind
38、rical container 2 Vibrating system 4 Tray to collect powder Figure 1 Apparatus Licensed Copy: Wang Bin, na, Mon May 15 06:44:28 BST 2006, Uncontrolled Copy, (c) BSIEN 725-9:2006 (E) 9 Annex A (informative) Repeatability and reproducibility The experience of three laboratories indicates that, for an
39、alumina powder with an un-tapped bulk density of 909 kg/m3, the method is capable of achieving: a) standard deviation of repeatability of 7 kg/m; b) standard deviation of reproducibility of 9 kg/m. Licensed Copy: Wang Bin, na, Mon May 15 06:44:28 BST 2006, Uncontrolled Copy, (c) BSIBS EN 725-9:2006B
40、SI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are upd
41、ated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British
42、 Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically rec
43、eive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.b
44、si-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standar
45、ds through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing memb
46、ers of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding
47、online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationa
48、l standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does n
49、ot preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.Licensed Copy: Wang Bi
