1、BRITISH STANDARD BSEN 10265:1996 Magnetic materials Specification for steel sheet and strip with specified mechanical properties and magnetic permeability The European Standard EN10265:1995 has the status of a British Standard ICS 29.040.10; 77.140.50BSEN10265:1996 This British Standard, having been
2、 prepared under the directionof the Engineering SectorBoard, was published underthe authority of the Standards Board and comes into effect on 15 June1996 BSI 06-1999 The following BSI references relate to the work on this standard: Committee reference ISE/NFE/5 Draft for comment87/40325 DC ISBN 0 58
3、0 25546 8 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ISE/NFE/5, Magnetic alloys and steels, upon which the following bodies were represented: Association of Manufacturers Allied to the Electrical and Electronic Indus
4、try (BEAMA Ltd.) British Steel Industry Department of Trade and Industry (National Physical Laboratory) Electricity Supply Industry in England and Wales GAMBICA (BEAMA Ltd.) Institute of Physics Rotating Electrical Machines Association (BEAMA Ltd.) Sunderland Polytechnic (Magnet Centre) Transmission
5、 and Distribution Association (BEAMA Ltd.) Wolfson Centre for Magnetics Technology Co-opted members Amendments issued since publication Amd. No. Date CommentsBSEN10265:1996 BSI 06-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN10265 3 List of
6、 references Inside back coverBSEN 10265:1996 ii BSI 06-1999 National foreword This British Standard has been prepared by Technical Committee ISE/NFE/5 and is the English language version of EN10265 Magnetic materials Specification for steel sheet and strip with specified mechanical properties and ma
7、gnetic permeability, published by the European Committee for Standardization (CEN). This British Standard replaces BS6404-8.5:1990, which is withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their corr
8、ect application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publication referred to Corresponding British Standard BS4727 Glossary of electrotechnical, power, telecommunications, electronics, lighting and colour terms IEC50 (121):19
9、78 Part 1: Group1:1983 Fundamental terminology IEC50 (221):1990 Part 1: Group7:1991 Magnetic materials and components BS6404 Magnetic materials IEC404-1:1979 Part 1:1984 Classification IEC404-2:1978 Part2:1985 Methods of measurement of magnetic, electrical and physical properties of magnetic sheet a
10、nd strip IEC404-4:1982 Part4:1986 Methods of measurement of the d.c. magnetic properties of solid steels EN10002-1:1990 BS EN10002 Tensile testing of metallic materials Part1:1990 Method of test at ambient temperature EN10021:1993 BS EN10021:1993 General technical delivery requirements for steel and
11、 iron products EN10027-2:1991 BS EN10027 Designation systems for steels Part2:1992 Steel numbers Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2 to12, an inside back cover and a back cover. This standard has been updated (see copy
12、right date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN10265 December1995 ICS 29.040.10; 77.140.50 Descriptors: Metal plates, steels, magneticalloys, specifications, mechanical
13、properties, magnetic permeability English version Magnetic materials Specification for steel sheet and strip with specified mechanical properties and magnetic permeability Matriaux magntiques Spcification des tles en acier caractristiques mcaniques et permabilit magntique garanties Magnetische Werks
14、toffe Anforderungen an Blech und Band aus Stahl mit festgelegten mechanischen un magnetischen Eigenschaften This European Standard was approved by CEN on1995-05-13. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Stand
15、ard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French,
16、German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, Franc
17、e, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 199
18、5 All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and its members. Ref. No. EN10265:1995 EEN10265:1995 BSI 06-1999 2 Foreword This European Standard has been prepared by the Technical Committee ECISS/TC24, Electrical steel sheet and strip qu
19、alities Qualities, dimensions, tolerances and specific tests, of which the secretariat is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June1996, and conflicting national standard
20、s shall be withdrawn at the latest by June1996. IEC Publication404-8-5 was submitted to the primary questionnaire (PQ) procedure in CEN and CENELEC. This European Standard is technically in accordance with IEC404-8-5 with some editorial amendments. According to the CEN/CENELEC Internal Regulations,
21、the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Normative refere
22、nces 3 3 Definitions 3 3.1 Flatness 3 3.2 Edge camber 3 4 Classification 3 5 Designation 4 6 General requirements 4 6.1 Production process 4 6.2 Form of supply 4 6.3 Delivery condition 4 6.4 Surface condition 5 6.5 Suitability for cutting 5 6.6 Suitability for welding 5 7 Technical requirements 5 7.
23、1 Mechanical properties 5 7.2 Magnetic properties 5 7.3 Geometrical characteristics and tolerances 5 8 Inspection 8 8.1 General 8 8.2 Selection of samples 8 8.3 Preparation of test specimens 8 8.4 Test method 9 9 Additional tests 10 10 Complaints 10 11 Ordering information 10 Figure 1 Wave factor in
24、 the case of a length of strip 11 Figure 2 Flatness in the case of a sheet 11 Figure 3 Verification of the edge camber 12 Table 1 Mechanical and magnetic characteristics of hot-rolled products 10 Table 2 Mechanical and magnetic characteristics of cold-rolled products 11EN10265:1995 BSI 06-1999 3 1 S
25、cope This European Standard defines the grades of steel sheet and strip with specified mechanical properties and magnetic permeability. In particular it gives the technological, mechanical and magnetic properties, the dimensional tolerances as well as the conditions of acceptance. This European Stan
26、dard applies to material used for the poles and rims of rotating electrical machines. These materials correspond to clause D2 of IEC404-1. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cite
27、d at the appropriate places in the text and the publications are listed hereafter. For dated references subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition
28、 of the publication referred to applies. IEC50 (121), International Electrotechnical Vocabulary (IEV), Chapter121: Electromagnetism. IEC50 (221), International Electrotechnical Vocabulary (IEV), Chapter221: Magnetism. IEC404-1, Magnetic materials Part1: Classification. IEC404-2, Magnetic materials P
29、art2: Methods of measurement of magnetic, electrical and physical properties of magnetic sheet and strip. IEC404-4, Magnetic materials Part4: Methods of measurement of the d.c. magnetic properties of solid steels. EN10002-1, Metallic materials Tensile testing Part1: Method of test (at ambient temper
30、ature). EN10021, General technical delivery conditions for iron and steel products. EN10027-2, Designation systems for steels Part2: Numerical system. ISO2566-1, Steel Conversion of elongation values Part1: Carbon and low alloy steels. 3 Definitions The definition of the principal terms relative to
31、magnetic characteristics employed in this standard are given in IEC50 (121) and IEC50 (221). In addition, for the purpose of this European Standard, the following definitions apply. 3.1 flatness 3.1.1 flatness of a sheet the maximum height of any point of the sheet above a flat horizontal surface, t
32、he sheet resting freely on this surface 3.1.2 flatness of a strip the property of a length of strip which is characterized by the wave factor, i.e.by the relation of the height of the wave to its length 3.2 edge camber the greatest distance between one longitudinal edge of a length of strip and the
33、line joining the two ends of the measured section corresponding to this edge 4 Classification The grades covered by this standard are classified according to the minimum value of the0,2% proof stress in newtons per square millimetre 1)and according to the minimum value of the magnetic flux density f
34、or a magnetic field strength of15kA/m. 1) 1N/mm 2 =1MPaEN10265:1995 4 BSI 06-1999 The grades are classified in two groups according to their manufacturing process: hot-rolled materials and cold-rolled materials. 5 Designation 5.1 The conventional designation 2)of the different grades comprises the f
35、ollowing in the order given: 1) the specified minimum value of the0,2% proof stress of the material, in newtons per square millimetre; 2) one hundred times the nominal thickness of the product, in millimetres; 3) the characteristic letters: TF for cold-rolled material, and TG for hot-rolled material
36、; 4) one hundred times the specified minimum value of the magnetic flux density in teslas for a magnetic field strength of15kA/m. Example 350 100 TF181 for a cold-rolled material with a minimum magnetic flux density of1,81 T for a magnetic field strength of15kA/m, a specified minimum0,2% proof stres
37、s of350N/mm 2 , and a nominal thickness of1,0mm. 5.2 The numerical designation is in accordance with EN10027-2. 6 General requirements 6.1 Production process The production process of the steel and its chemical composition are left to the discretion of the manufacturer. 6.2 Form of supply The materi
38、al is supplied in bundles in the case of sheets and in coils in the case of strip. The sheets which make up each bundle shall be stacked so that their edges are superimposed in a regular manner. The strip shall be of constant width, and wound in such a way that the edges are superimposed in a regula
39、r manner and the end faces of the coil are substantially flat. The coils shall be sufficiently tightly wound that they do not collapse under their own weight. The strips may occasionally exhibit welds or interleaves resulting from the junction made after removal of the defective zones or from the jo
40、ining of several lengths to obtain the sizes of the coils required by the user. In the absence of prior agreement, the form of repair is left to the discretion of the manufacturer. The welds or interleaves shall be marked. For coils containing repair welds or interleaves, each part of the strip shal
41、l be of the same quality. The edges of the parts welded together shall not be so much out of alignment that their ability to be worked is affected. Material supplied in sheets shall not contain any welds. The mass of bundles of sheet or coils shall be agreed at the time of ordering. 6.3 Delivery con
42、dition The materials are normally supplied without an insulating coating. By agreement, the materials can be supplied with an insulating coating on one or both sides. In this case, the nature of the insulating coating, its properties and their verification shall be subject to special agreement when
43、ordering. Materials produced by hot-rolling are normally supplied with an oxide scale coating unless they have been ordered pickled. By agreement, the products can be supplied lightly coated with oil. Coils supplied with trimmed edges and sheets shall not contain burrs or cutting distortions which a
44、re prejudicial to the method of working of the material. 2) The designation of steel products specified in this standard is not included in EN10027-1; therefore, the designations used are those in IEC404-8-5.EN10265:1995 BSI 06-1999 5 6.4 Surface condition Unless indicated otherwise, the surfaces sh
45、all be smooth and clean, free from grease and rust as well as all other defects such as scratches, blisters, cracks etc. (see clause10). However, dispersed defects can be tolerated if they are within the tolerance limits for thickness and if they are not detrimental to the correct use of the finishe
46、d product. 6.5 Suitability for cutting The material shall be capable of being cut or punched without causing premature wear of tools; it shall be able to be cut at any point and in the usual shapes thus ensuring precise working with appropriate tools in good condition. If there are special requireme
47、nts for an acceptance test for punching or shearing, these shall be established between the supplier and the purchaser. 6.6 Suitability for welding The suitability for welding of the material can be the subject of agreement when ordering. 7 Technical requirements 7.1 Mechanical properties The minimu
48、m specified values of the0,2% proof stress (R p0,2 ), of the tensile strength (R m ) and of the percentage elongation after fracture (A 80mm ) are given in Table 1 and Table 2. 7.2 Magnetic properties The minimum specified values for the magnetic flux density for magnetic field strengths of5000A/m a
49、nd15000A/m are given in Table 1 and Table 2. 7.3 Geometrical characteristics and tolerances 7.3.1 Thickness The recommended nominal thicknesses are the following: hot-rolled materials:1,6mm,1,8mm,2,0mm,2,5mm,3,0 mm,3,2mm and4,5mm; cold-rolled materials:0,5mm,1,0mm,1,6mm,1,8mm, and2,0 mm. For thickness tolerance, a distinction is made between: the variation in nominal thickness within the same unit of acceptance; the variation in thickness of a sheet or in a length of strip in a direction parallel to the directio
