1、BS EN 12200-1:2016Plastics rainwater pipingsystems for above groundexternal use Unplasticizedpoly(vinyl chloride) (PVC-U)Part 1: Specifications for pipes, fittings andthe systemBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 12200-1:2016 BRITISH STANDARDNationa
2、l forewordThis British Standard is the UK implementation of EN 12200-1:2016. It supersedes BS EN 12200-1:2000 which is withdrawn.The responsible UK committee gives the following advice concerning the scope and contents of EN 12200-1.a) EN 12200-1:2016 has been extended to cover pipes manufactured by
3、 multi-layer co-extrusion and the use of acrylic materials for both the outer layer of the pipe and the fittings. It also allows greater use of recycled PVC-U material.b) EN 12200-1:2016 is specific to rainwater downpipe systems installedoutdoors. For indoor rainwater downpipe reference should bemad
4、e to standards for soil and waste discharge within the buildingstructure, e.g. BS EN 1329-1:2014.NOTE In the UK, plastics rainwater downpipe systems installed outdoors normally have “unsealed” joints (see Table 2 which details wall thickness requirements for both sealed and unsealed systems).c) Sinc
5、e in Table 12 reference is made to “stage 3” of the grey scaleaccording to EN 20105-A02, the reference here and to this standard inclause 2 should be considered to relate to the latest published edition(currently 1995) of that standard.d) The unique UK diameter of 82.4 mm minimum (mean outsidediamet
6、er) as detailed in BS 4514 is not listed in Table 1 but iscommonly used for rainwater applications in the UK. It is advised thatpipes and fittings to this size will still be able to be marked EN 12200-1when manufactured in accordance with the diameter tolerancesspecified in BS 4514 and using the gen
7、eral rules for other dimensionssuch as wall thickness as detailed in Clause 6.2.2 of this standard.The UK participation in its preparation was entrusted by Technical Committee PRI/88, Plastics piping systems, to Subcommittee PRI/88/1, Plastics piping for non-pressure applications.A list of organizat
8、ions represented on this subcommittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 201
9、6ISBN 978 0 580 87508 3ICS 23.040.20; 91.060.20Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2016.Amendments/corrigenda issued since publicationDate Te
10、xt affectedBS EN 12200-1:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12200-1 April 2016 ICS 23.040.20 Supersedes EN 12200-1:2000English Version Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) -Part 1: Specifications for pipes,
11、 fittings and the system Systmes de canalisations de descentes deaux pluviales en plastique usage externe en arien - Poly(chlorure de vinyle) non plastifi (PVC-U) - Partie 1: Spcifications pour tubes, raccords et le systme Kunststoff-Rohrleitungssysteme fr auenliegende Regenfallleitungen - Weichmach
12、erfreies Polyvinylchlorid (PVC-U) - Teil 1: Anforderungen an Rohre, Formstcke und das Rohrleitungssystem This European Standard was approved by CEN on 9 January 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Sta
13、ndard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (Engli
14、sh, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, B
15、ulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
16、 Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Member
17、s. Ref. No. EN 12200-1:2016 EBS EN 12200-1:2016EN 12200-1:2016 (E) 2 Contents Page European foreword . 4 1 Scope 6 2 Normative references 6 3 Terms, definitions, symbols and abbreviations . 7 3.1 Terms and definitions 7 3.2 Definitions of multilayer pipes . 8 3.3 Material terms and definitions . 9 3
18、.4 Definitions for brackets 9 3.5 Symbols 10 3.6 Abbreviations 10 4 Material 10 4.1 PVC-U material 10 4.2 Other materials . 11 4.3 Utilization of non-virgin material . 11 4.4 Sealing ring retaining means 11 4.5 Metallic brackets 11 5 General characteristics - appearance 11 6 Geometrical characterist
19、ics 11 6.1 General . 11 6.2 Dimensions of pipes 11 6.2.1 Diameters of circular pipes . 11 6.2.2 Outside dimensions and tolerances of non-circular pipes 12 6.2.3 Effective length of pipes . 13 6.2.4 Wall thicknesses of pipes and their sockets . 13 6.2.5 Dimensions of sockets 15 6.3 Dimensions of fitt
20、ings . 15 6.3.1 Nominal size(s) 15 6.3.2 Wall thicknesses of fittings . 15 6.3.3 Angles 15 6.3.4 Design lengths (Zd) 15 6.4 Diameters and lengths of sockets and spigots . 15 6.4.1 Ring seal sockets and spigots . 15 6.4.2 Solvent cement and unsealed sockets and spigots . 17 6.4.3 Non-circular sockets
21、 and spigots 19 6.4.4 Spigot sleeves . 19 6.5 Types of fittings . 19 6.6 Brackets . 22 7 Mechanical characteristics 22 7.1 Pipes 22 7.2 Mechanical characteristics of anchor brackets . 24 8 Physical characteristics 25 8.1 Physical characteristics of pipes . 25 8.2 Physical characteristics of fittings
22、 . 26 BS EN 12200-1:2016EN 12200-1:2016 (E) 3 9 Fitness for purpose of joint and system . 26 10 Sealing rings . 27 11 Adhesives . 27 12 Marking 27 12.1 General . 27 12.2 Minimum required marking of pipes 28 12.3 Minimum required marking of fittings . 28 12.4 Minimum required marking of brackets . 29
23、 Annex A (informative) Utilization of non-virgin material 30 A.1 Own reprocessed material 30 A.2 External reprocessed and recycled material with agreed specification 30 A.3 External reprocessed and recycled material not covered by an agreed specification 31 Annex B (informative) Survey of possible u
24、se of reprocessed and recycled material . 33 Bibliography . 34 BS EN 12200-1:2016EN 12200-1:2016 (E)2BS EN 12200-1:2016EN 12200-1:2016 (E) 2 Contents Page European foreword . 4 1 Scope 6 2 Normative references 6 3 Terms, definitions, symbols and abbreviations . 7 3.1 Terms and definitions 7 3.2 Defi
25、nitions of multilayer pipes . 8 3.3 Material terms and definitions . 9 3.4 Definitions for brackets 9 3.5 Symbols 10 3.6 Abbreviations 10 4 Material 10 4.1 PVC-U material 10 4.2 Other materials . 11 4.3 Utilization of non-virgin material . 11 4.4 Sealing ring retaining means 11 4.5 Metallic brackets
26、 11 5 General characteristics - appearance 11 6 Geometrical characteristics 11 6.1 General . 11 6.2 Dimensions of pipes 11 6.2.1 Diameters of circular pipes . 11 6.2.2 Outside dimensions and tolerances of non-circular pipes 12 6.2.3 Effective length of pipes . 13 6.2.4 Wall thicknesses of pipes and
27、their sockets . 13 6.2.5 Dimensions of sockets 15 6.3 Dimensions of fittings . 15 6.3.1 Nominal size(s) 15 6.3.2 Wall thicknesses of fittings . 15 6.3.3 Angles 15 6.3.4 Design lengths (Zd) 15 6.4 Diameters and lengths of sockets and spigots . 15 6.4.1 Ring seal sockets and spigots . 15 6.4.2 Solvent
28、 cement and unsealed sockets and spigots . 17 6.4.3 Non-circular sockets and spigots 19 6.4.4 Spigot sleeves . 19 6.5 Types of fittings . 19 6.6 Brackets . 22 7 Mechanical characteristics 22 7.1 Pipes 22 7.2 Mechanical characteristics of anchor brackets . 24 8 Physical characteristics 25 8.1 Physica
29、l characteristics of pipes . 25 8.2 Physical characteristics of fittings . 26 BS EN 12200-1:2016EN 12200-1:2016 (E) 3 9 Fitness for purpose of joint and system . 26 10 Sealing rings . 27 11 Adhesives . 27 12 Marking 27 12.1 General . 27 12.2 Minimum required marking of pipes 28 12.3 Minimum required
30、 marking of fittings . 28 12.4 Minimum required marking of brackets . 29 Annex A (informative) Utilization of non-virgin material 30 A.1 Own reprocessed material 30 A.2 External reprocessed and recycled material with agreed specification 30 A.3 External reprocessed and recycled material not covered
31、by an agreed specification 31 Annex B (informative) Survey of possible use of reprocessed and recycled material . 33 Bibliography . 34 BS EN 12200-1:2016EN 12200-1:2016 (E)3BS EN 12200-1:2016EN 12200-1:2016 (E) 4 European foreword This document (EN 12200-1:2016) has been prepared by Technical Commit
32、tee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. This document supersedes EN 12200-1:2000. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Oct
33、ober 2016, and conflicting national standards shall be withdrawn at the latest by October 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such paten
34、t rights. This European Standard has been prepared in liaison with CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cladding” taking into account EN 607 1 and EN 1462 and CEN/TC 165 “Waste water engineering” taking into account the design guidance in EN 12056-3 4. Th
35、is standard is a Part of a System Standard for plastics piping systems of a particular material for a specified application. There are a number of such System Standards. System Standards are based on the results of the work undertaken in ISO/TC 138 “Plastics pipes, fittings and valves for the transp
36、ort of fluids”, which is a Technical Committee of the International Organization for Standardization (ISO). They are supported by separate standards on test methods to which references are made throughout the System Standard. The System Standards are consistent with general standards on functional r
37、equirements and on recommended practice for installation. EN 12200 consists of the following Parts, under the general title “Plastics rainwater piping systems for above ground external use Unplasticized poly(vinyl chloride) (PVC-U)”: Part 1: Requirements for pipes fittings and the system (the presen
38、t standard); Part 2: Guide for the assessment of conformity 3. For Rainwater discharge systems used internally within buildings the following standards apply: EN 1329, Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure Unplasticized poly(vin
39、yl chloride) (PVC-U) EN 1451, Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure Polypropylene (PP) EN 1453, Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings Unplasti
40、cized poly(vinyl chloride) (PVC-U) BS EN 12200-1:2016EN 12200-1:2016 (E) 5 EN 1455, Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure Acrylonitrile-butadiene-styrene (ABS) EN 1519, Plastics piping systems for soil and waste discharge (low a
41、nd high temperature) within the building structure Polyethylene (PE) EN 1565, Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure Styrene copolymer blends (SAN+PVC) EN 1566, Plastics piping systems for soil and waste discharge (low and high t
42、emperature) within the building structure Chlorinated poly(vinyl chloride) (PVC-C) According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Repu
43、blic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS E
44、N 12200-1:2016EN 12200-1:2016 (E)4BS EN 12200-1:2016EN 12200-1:2016 (E) 4 European foreword This document (EN 12200-1:2016) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. This document supersedes EN 12200-1:
45、2000. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2016, and conflicting national standards shall be withdrawn at the latest by October 2016. Attention is drawn to the possibility that
46、some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This European Standard has been prepared in liaison with CEN/TC 128 “Roof covering products for discontinuous laying and products
47、 for wall cladding” taking into account EN 607 1 and EN 1462 and CEN/TC 165 “Waste water engineering” taking into account the design guidance in EN 12056-3 4. This standard is a Part of a System Standard for plastics piping systems of a particular material for a specified application. There are a nu
48、mber of such System Standards. System Standards are based on the results of the work undertaken in ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”, which is a Technical Committee of the International Organization for Standardization (ISO). They are supported by separate
49、standards on test methods to which references are made throughout the System Standard. The System Standards are consistent with general standards on functional requirements and on recommended practice for installation. EN 12200 consists of the following Parts, under the general title “Plastics rainwater piping systems for above ground external use Unplasticized poly(vinyl chloride) (PVC-U)”: Part 1: Requirements for pipes fittings and the system (the present standard); Part 2: Guide for the assessment of conformity 3. For Rainwa
