BS EN 14073-2-2004 Office furniture - Storage furniture - Safety requirements《办公家具 储存用家具 安全要求》.pdf

上传人:tireattitude366 文档编号:572145 上传时间:2018-12-13 格式:PDF 页数:14 大小:267.55KB
下载 相关 举报
BS EN 14073-2-2004 Office furniture - Storage furniture - Safety requirements《办公家具 储存用家具 安全要求》.pdf_第1页
第1页 / 共14页
BS EN 14073-2-2004 Office furniture - Storage furniture - Safety requirements《办公家具 储存用家具 安全要求》.pdf_第2页
第2页 / 共14页
BS EN 14073-2-2004 Office furniture - Storage furniture - Safety requirements《办公家具 储存用家具 安全要求》.pdf_第3页
第3页 / 共14页
BS EN 14073-2-2004 Office furniture - Storage furniture - Safety requirements《办公家具 储存用家具 安全要求》.pdf_第4页
第4页 / 共14页
BS EN 14073-2-2004 Office furniture - Storage furniture - Safety requirements《办公家具 储存用家具 安全要求》.pdf_第5页
第5页 / 共14页
点击查看更多>>
资源描述

1、BRITISH STANDARDBS EN 14073-2:2004Incorporating Amendment No. 1Office furniture Storage furniture Part 2: Safety requirementsThe European Standard EN 14073-2:2004 has the status of a British StandardICS 97.140g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g5

2、0g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 14073-2:2004This British Standard was published under the authority of the Standards Policy and Strategy Committee on 4 November 2004 BSI 15 February 2006ISBN 0 580 46582 9National fore

3、wordThis British Standard is the official English language version of EN 14073-2:2004. It supersedes BS 5459-3:1983 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee FW/0, Furniture, which has the responsibility to: National annex NA (informative) gives

4、 guidance on the durability performance of office furniture for use in the UK.A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document ma

5、y be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users a

6、re responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK

7、interests informed; monitor related international and European developments and promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 10, an inside back cover and a back cover.The BSI copyright notice displayed in this d

8、ocument indicates when the document was last issued.Amendments issued since publicationAmd. No. Date Comments15868 Amendment No. 1February 2006 Addition of supersession details and a national annex NA.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 14073-2August 2004ICS 97.140English versionOffice

9、 furniture - Storage furniture - Part 2: Safety requirementsMobilier de bureau - Meubles de rangement - Partie 2 :Exigences de scuritBrombel - Broschrnke - Teil 2: SicherheitstechnischeAnforderungenThis European Standard was approved by CEN on 27 May 2004.CEN members are bound to comply with the CEN

10、/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to an

11、y CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN m

12、embers are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and Un

13、ited Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2004 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14073-2:2004:

14、EEN 14073-2:2004 (E) 2 Contents page Foreword3 1 Scope 4 2 Normative references 4 3 Safety Requirements .4 3.1 Principles4 3.2 Determination of the centre of gravity.5 3.3 Determination of total mass .5 3.4 General safety requirements 5 3.5 Floor standing units - free standing or attached to the bui

15、lding6 3.6 Screen and wall hanging units.7 Annex A (informative) Adeviations9 EN 14073-2:2004 (E) 3 Foreword This document (EN 14073-2:2004) has been prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of which is held by UNI. This European Standard shall be given the status of a

16、 national standard, either by publication of an identical text or by endorsement, at the latest by February 2005, and conflicting national standards shall be withdrawn at the latest by February 2005. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the follo

17、wing countries are bound to: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

18、 EN 14073-2:2004 (E) 4 1 Scope This document specifies safety requirements for office storage furniture. This document does not apply to high density mechanized filing systems, rotary filing systems or plan files. It should be understood that fulfilling the specified requirements does not ensure tha

19、t failure will not occur as a result of habitual misuse or after an excessively long period of service. Safety depending on structure of the building is not included e.g.: the strength of wall hanging cabinets includes only the cabinet and its parts. The wall and wall attachment are not included. As

20、sessment of ageing is not included. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)

21、 applies. EN 14073-3:2004 Office furniture - Storage furniture - Part 3: Test methods for the determination of stability and strength of the structure EN 14074:2004 Office furniture Tables and desks and storage furniture - Test methods for the determination of strength and durability of moving parts

22、. 3 Safety Requirements 3.1 Principles Storage furniture shall be designed so as to minimise the risk of injury in normal use. The following safety requirements are based upon the knowledge that office storage furniture and its parts are likely to cause injury only when they are heavy and fall throu

23、gh a significant distance. This is possible if floor standing units overbalance, wall or screen mounted units become detached, or heavy parts become detached from units. Therefore, the test sequence and the safety requirements specified in clause 3.5 and 3.6 are applicable: When the height of the ce

24、ntre of gravity of the unit, or any part is 650mm above the floor and the total mass is 10kg When the potential energy is 65 Nm and the distance from the floor to the lowest edge of the unit or any part is 300mm The potential energy is the multiplication of the total mass of the unit, or the part, a

25、nd the height above the floor in meter (m) to the centre of gravity. EN 14073-2:2004 (E) 5 3.2 Determination of the centre of gravity The centre of gravity of a part or unit shall be taken as the geometric centre of the useable volume of drawers and units, and as the geometric centre of doors, flaps

26、 and shelves. The height of the centre of gravity above the floor shall be measured for units or their parts when installed according to the manufacturers instructions. Floor levelling devices shall be set at their middle position. Storage units that can be positioned at alternative heights shall be

27、 placed in their highest position. All wall or top-mounted units, or parts thereof, are considered to have their centre of gravity more than 650mm above the floor, unless specific restrictions are made by the manufacturer. 3.3 Determination of total mass The total mass is the mass of the part or uni

28、t plus the mass supported by it. Unless conspicuously and durably marked by the manufacturer with a maximum allowable contents load, the mass of the contents shall be determined according to Table 1, which specifies load per unit area for shelves, load per unit volume for extension elements and load

29、 per unit length for clothes rails. The volume of extension elements shall be taken as the area of its bottom multiplied by the clear height. The clear height is the distance between the top of the extension element bottom and the lower edge of the extension element above, or the structure of the un

30、it. Table 1 Loads on storage parts Shelves kg/dm 1,5Clothes rails kg/dm 5,0 Extension elements kg/dm 0,5 Suspended pocket files kg/dm a)4,0 a)Measured perpendicular to the plane of the pocket files. 3.4 General safety requirements Accessible edges and corners shall be free from burrs and rounded or

31、chamfered. There shall be no open ended tubes. All moveable parts accessible during normal use shall have safety distances in any position during movement of 8mm or 25mm. This applies to any two elements moving relatively to each other, with the exception of doors (incl. hinges), flaps (incl. hinges

32、) and extension elements (incl. runners). The safety distances also apply to the distance between handles and other parts. Adjustable parts shall be such as to prevent inadvertent operation or release. If there is a risk of injury, vertically sliding roll fronts shall not close by themselves from an

33、y position higher than 200mm measured from the closed position. Extension elements shall have effective open stops, i.e. they shall resist being pulled out of the carcass once by a horizontal force of 200 N applied to the handle of the loaded extension element. EN 14073-2:2004 (E) 6 3.5 Floor standi

34、ng units - free standing or attached to the building 3.5.1 Test sequence for floor standing units free standing or attached to the building The safety tests listed in Table 2 shall be carried out according to EN 14073-3 and EN 14074. It is accepted that the safety tests from EN 14073-3 and EN 14074

35、(see the table below) are part of a total test sequence, where all relevant tests according to EN 14073-3 and EN 14074 (also those which are not safety tests) are carried out. Table 2 Test sequence for floor standing units free standing or attached to the building Test n Test Reference 1 Pull out of

36、 shelves EN 14073-3:2004, 5.3.1 2 Strength of shelf supports EN 14073-3:2004, 5.3.2 3 Strength of top surfaces EN 14073-3:2004, 5.4 4 Strength of extension elements EN 14074:2004, 6.2.1 5 Slam open of extension elements EN 14074:2004, 6.2.3 6 Interlock test EN 14074:2004, 6.2.4 7 Vertical load on pi

37、voted door EN 14074:2004, 6.3.1 8 Slam shut/open of sliding doors and horizontal roll fronts EN 14074:2004, 6.4.2 9 Strength of flaps EN 14074:2004, 6.6.1 10 Floor standing units attached to the building EN 14073-3:2004, 5.7 11 Stabilitya EN 14073-3:2004, 5.5.1 and 5.5.2 aIn the case of units, which

38、 might not fulfil the stability requirements before carrying out any tests, the applicable stability tests may be carried out before starting the sequence of tests specified in the table. EN 14073-2:2004 (E) 7 3.5.2 Safety requirements After carrying out the tests specified in clause 3.5.1 there sha

39、ll be no fracture, other damage or change of function that affects the safety. This also implies that after testing there shall be no sharp edges, sharp points etc. Additional requirements after the testing in accordance with: 5.3.1 of EN 14073-3:2004, the shelf shall remain in the unit. 5.2 of EN 1

40、4073-3:2004, if one unit is intended to stand upon another, it shall not slide under the applied force. 6.3.1 of EN 14074:2004, the door shall remain attached to the unit. 6.2.3 of EN 14074:2004, the extension element shall not fall out of the unit. 6.2.4 of EN 14074:2004, the extension element shal

41、l remain closed. 5.7 of EN 14073-3:2004, the unit shall remain attached to the building. 5.5.1 and 5.5.2 of EN 14073-3:2004, the unit shall not overturn. 3.6 Screen and wall hanging units 3.6.1 Test sequence for screen and wall hanging units All tests listed in table 3 shall be carried out with the

42、unit hanging on the screen or wall. Table 3 Test sequence for screen and wall hanging units Test n Test Reference 1 Dislodgement of screen and wall mounted units EN 14073-3:2004, 5.6.2 2 Pull out of shelves EN 14073-3:2004, 5.3.1 3 Strength of shelf supports EN 14073-3:2004, 5.3.2 4 Strength of top

43、surfaces EN 14073-3:2004, 5.4 5 Strength of extension elements EN 14074:2004, 6.2.1 6 Slam open of extension elements EN 14074:2004, 6.2.3 7 Interlock test EN 14074:2004, 6.2.4 8 Vertical load on pivoted door EN 14074:2004, 6.3.1 9 Slam shut/open of sliding doors and horizontal roll fronts EN 14074:

44、2004, 6.4.2 10 Strength of flaps EN 14074:2004, 6.6.1 11 Strength of screen and wall attachment devices EN 14073-3:2004, 5.6.4 EN 14073-2:2004 (E) 8 3.6.2 Safety requirements With the exception of the test according to 5.6.4 of EN 14073-3:2004 (test no. 11), there shall be no fracture, other damage

45、or change of function that affects the safety after carrying out the tests specified in clause 3.6.1. This also implies that after testing there shall be no sharp edges, sharp points etc. After testing according to 5.6.4 of EN 14073-3:2004 (test no. 11), the unit shall remain attached as mounted and

46、 shall support the test load. Additional requirements after testing in accordance with: 5.3.1 of EN 14073-3:2004, the shelf shall remain in the unit. 6.3.1 of EN 14074:2004, the door shall remain attached to the unit. 6.2.3 of EN 14074:2004, the extension element shall not fall out of the unit. 6.2.

47、4 of EN 14074:2004, the extension element shall remain closed. EN 14073-2:2004 (E) 9 Annex A (informative) Adeviations A- deviation: National deviation due to regulations, the alteration of which is for the time being outside the competence of the CEN/ CENELEC member. This document does not fall und

48、er any Directive of the EU. In the relevant CEN/ CENELEC countries these A- deviations are valid instead of the provisions of the document until they have been removed. In Germany the following regulations exist: The “Arbeitsstttenverordnung“ and the “Gesetz ber technische Arbeitsmittel (Gertesicher

49、heitsgesetz) in der Fassung von 23. Oktober 1992, Bundesgesetzblatt III 8053-4“ lays down that storage furniture shall conform to the German Standard DIN 4554. BS EN 14073-2:2004 BSI 15 February 200610National Annex A (informative) Durability performanceNA.1 EN 14074 contains tests for the durability of storage furniture parts. EN 14073-2 specifies only safety requirements and does not contain corresponding requirements to the durability tests.In the UK, customers are accustomed to testing for both safety and durability

展开阅读全文
相关资源
  • BS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdfBS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdf
  • BS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdfBS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdf
  • BS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdfBS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdf
  • BS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdfBS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdf
  • BS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdfBS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf
  • BS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdfBS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdf
  • BS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdfBS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdf
  • BS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdfBS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdf
  • BS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdfBS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdf
  • BS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdfBS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > BS

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1