1、BS EN 15216:2007ICS 13.030.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDCharacterization ofwaste Determinationof total dissolved solids(TDS) in water andeluatesLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 07:34, Uncontrolled Copy, (c) B
2、SIThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 May 2009 BSI 2009ISBN 978 0 580 55378 3Amendments/corrigenda issued since publicationDate CommentsBS EN 15216:2007National forewordThis British Standard is the UK implementation of EN 15216:200
3、7.The UK participation in its preparation was entrusted to TechnicalCommittee B/508/3, Characterization of waste.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Us
4、ers are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 07:34, Uncontrolled Copy, (c) BSIBS EN 15216:2007EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15216Oc
5、tober 2007ICS 13.030.20English VersionCharacterization of waste - Determination of total dissolvedsolids (TDS) in water and eluatesCaractrisation des dchets - Dtermination de laconcentration en matires solides dissoutes totales (TDS)de leau et des luatsCharakterisierung von Abfllen - Bestimmung desG
6、esamtgehaltes an gelsten Feststoffen (TDS) in Wasserund EluatenThis European Standard was approved by CEN on 1 September 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard wi
7、thout any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language
8、 made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,Fran
9、ce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NOR
10、MUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15216:2007: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 07:34, Uncontrolled Copy, (c) BSIBS EN 152
11、16:2007EN 15216:2007 (E) 2 Contents Page Foreword3 Introduction .4 1 Scope 5 2 Terms and definitions .5 3 Principle5 4 Sample storage and preparation5 5 Equipment 5 6 Procedure .6 7 Calculation of results 6 8 Quality control6 9 Performance characteristics 7 10 Test report 7 Annex A (informative) Sum
12、mary of general requirements and recommendations .8 Bibliography 9 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 07:34, Uncontrolled Copy, (c) BSIBS EN 15216:2007EN 15216:2007 (E) 3 Foreword This document (EN 15216:2007) has been prepared by Technical Committee CEN/TC 292 “Charac
13、terization of waste”, the secretariat of which is held by NEN, in cooperation with CEN/TC 230. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2008, and conflicting national standards shall
14、be withdrawn at the latest by April 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regula
15、tions, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Nether
16、lands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 07:34, Uncontrolled Copy, (c) BSIBS EN 15216:2007EN 15216:2007 (E) 4 Introduction Total dissolved solids are a common sum
17、 parameter which is in use in water analysis and in analysis of eluates. TC 292 and TC 230 cooperated on this item to create one horizontal standard which is of most practical use for laboratories. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 07:34, Uncontrolled Copy, (c) BSIBS
18、EN 15216:2007EN 15216:2007 (E) 5 1 Scope This European standard specifies a method for the determination of total dissolved solids (TDS) in water and eluates, provided they are not volatile under the conditions specified or that they do not release water molecules from hydration. It applies to water
19、 and eluates containing more than 200 mg/l of total dissolved solids. Samples with lower amounts of dissolved solids can be analyzed by repetition of the drying step. 2 Terms and definitions For the purposes of this document, the following term and definition applies. 2.1 total dissolved solids TDS
20、TDSmass of dissolved constituents per unit volume of water remaining after a specified filtering and drying process NOTE TDS is expressed in milligrams per litre. 3 Principle The test sample is filtered and then dried in a dish to a constant mass in an oven at (105 3) C. 4 Sample storage and prepara
21、tion During storage, the laboratory sample may be subject to changes which are liable to influence the analysis result. If storage is necessary, samples shall be kept at (4 2) C. NOTE Freezing should be avoided due to risk of formation of precipitation. It is recommended to carry out the test immedi
22、ately after sampling of the water sample or preparation of the eluate. 5 Equipment 5.1 Drying system thermostatically controlled and capable of maintaining a temperature of (105 3) C; e.g. drying oven, infrared system. 5.2 Desiccator with an active drying agent such as silica gel. 5.3 Analytical bal
23、ance with an accuracy of 1 mg or better. 5.4 Membrane filter (porosity of 0,45 m). 5.5 Filtration apparatus. 5.6 Evaporation dish or crucible. Temperature tolerant laboratory vessel withstanding 105 C. Suitable materials are glass, ceramic, porcelain, aluminium and other materials inert to the test
24、portion. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 07:34, Uncontrolled Copy, (c) BSIBS EN 15216:2007EN 15216:2007 (E) 6 6 Procedure Filter the test sample through the membrane filter as specified in 5.4 unless it has been membrane filtered before (e. g. eluates prepared accor
25、ding to EN 12457). Dry the dish, for example in the oven, at (105 3) C and weigh to the nearest 1 mg (to obtain ma) after cooling to ambient temperature in the desiccator. Homogenise and transfer a proper aliquot (VFB) if necessary in stages, into the dish to ensure that not less than 20 mg and not
26、more than 1 000 mg of dry mass, mD, remains after evaporation to dryness. Evaporate the sample to dryness by a drying system according to 5.1 and weigh to the nearest 1 mg (to obtain mb) after cooling to ambient temperature in the desiccator. The mass of the dry matter, mD, shall be considered const
27、ant if, after drying for a further half-hour period, the mass obtained does not differ by more than 0,5 % of the previous value or 2 mg whichever is the greater. Otherwise, drying shall be repeated until constant mass has been reached. NOTE If a constant value is not obtained even after drying for a
28、 third time, record the value determined last and note this in the test report. 7 Calculation of results Calculate the total dissolved solids from equation (1): FBDTDSVm= (1) with mD= mb mawhere TDSis the concentration of total dissolved solids, in mg/l; mDis the mass of the dry matter, in mg; mais
29、the mass of the empty dish, in mg; mbis the mass of the dish containing the dry matter, in mg; VFBis the volume of the filtered test sample taken, in l. Values shall be rounded to the nearest 1 mg/l. 8 Quality control Where uncertainty exists about the homogeneity or behaviour of the sample, it is r
30、ecommended that the analysis is carried out in duplicate. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 07:34, Uncontrolled Copy, (c) BSIBS EN 15216:2007EN 15216:2007 (E) 7 9 Performance characteristics The method performance characteristics given in Table 1 have been established
31、 in a European intercomparison study on two surface water samples, two waste water samples and two eluates, carried out in 2006. Table 1 Performance characteristics for the determination of total dissolved solids in water and eluates Material p N O % Mean mg/l Sr% SR% Surface water A 17 34 0 478 2,1
32、5 4,49 Surface water B 17 34 0 3810 0,39 2,53 Waste water A 17 34 0 27300 1,34 4,33 Waste water B 17 34 0 4840 1,28 5,55 Eluate A 17 34 0 4090 1,74 6,27 Eluate B 17 34 0 3440 0,71 3,16 p is number of participating laboratories N is the number of outlier-free individual analytical results O is the pe
33、rcentage of outliers Sris the estimate of the relative repeatability standard deviation SRis the estimate of the relative reproducibility standard deviation 10 Test report The test report shall contain at least the following details: a) reference to this European standard; b) all data which are nece
34、ssary to identify the sample; c) calculated concentration of total dissolved solids; d) details of all procedural steps which deviate from this standard together with all circumstances that may have influenced the results; e) type of drying procedure. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STAN
35、DARDS, 01/09/2009 07:34, Uncontrolled Copy, (c) BSIBS EN 15216:2007EN 15216:2007 (E) 8 Annex A (informative) Summary of general requirements and recommendations Purpose of this summary is to support the organization of sampling and sample pre-treatment processes. The information given should be help
36、ful to prepare a sampling plan. Requirements not mentioned in the normative part of this document are considered as recommendations. Table A.1 Matrix restrictions Water and eluates. Typical working range Above 100 mg/l; lower values possible by repetition. Sampling instruments Any instrument that do
37、es not release soluble solids. Bottle pre-treatment Clean and dry. Bottle material Any bottle that does not release soluble solids. Transport conditions Dark and cool. Preservation Cooling at about 4 C. Storage conditions At 4 C in the dark not longer than 1 week; longer storage not recommended. Req
38、uired amount Depends on expected results. For 1 000 mg/l TDS about 250 ml of sample are sufficient. Test portion Typically 100 ml. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 07:34, Uncontrolled Copy, (c) BSIBS EN 15216:2007EN 15216:2007 (E) 9 Bibliography 1 EN 12457 (all parts
39、), Characterization of waste Leaching Compliance test for leaching of granular waste materials and sludges Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 07:34, Uncontrolled Copy, (c) BSIBS EN15216:2007BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 899
40、6 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendm
41、ent or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would in
42、form the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editi
43、ons of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response
44、 to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Lib
45、rary and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with
46、standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards
47、Online can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs
48、and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necess
49、ary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDAR
