BS EN 50289-3-10-2005 Communication cables - Specifications for tests methods - Mechanical test methods - Torsion and twisting《通信电缆 试验方法规范 机械试验方法 扭转》.pdf

上传人:figureissue185 文档编号:574730 上传时间:2018-12-13 格式:PDF 页数:12 大小:171.88KB
下载 相关 举报
BS EN 50289-3-10-2005 Communication cables - Specifications for tests methods - Mechanical test methods - Torsion and twisting《通信电缆 试验方法规范 机械试验方法 扭转》.pdf_第1页
第1页 / 共12页
BS EN 50289-3-10-2005 Communication cables - Specifications for tests methods - Mechanical test methods - Torsion and twisting《通信电缆 试验方法规范 机械试验方法 扭转》.pdf_第2页
第2页 / 共12页
BS EN 50289-3-10-2005 Communication cables - Specifications for tests methods - Mechanical test methods - Torsion and twisting《通信电缆 试验方法规范 机械试验方法 扭转》.pdf_第3页
第3页 / 共12页
BS EN 50289-3-10-2005 Communication cables - Specifications for tests methods - Mechanical test methods - Torsion and twisting《通信电缆 试验方法规范 机械试验方法 扭转》.pdf_第4页
第4页 / 共12页
BS EN 50289-3-10-2005 Communication cables - Specifications for tests methods - Mechanical test methods - Torsion and twisting《通信电缆 试验方法规范 机械试验方法 扭转》.pdf_第5页
第5页 / 共12页
亲,该文档总共12页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、BRITISH STANDARD BS EN 50289-3-10: 2004 Communication cables Specifications for tests methods Part 3-10: Mechanical test methods Torsion and twisting The European Standard EN 50289-3-10:2004 has the status of a British Standard ICS 33.120.10 BS EN 50289-3-10:2004 This British Standard was published

2、under the authority of the Standards Policy and Strategy Committee on 12 January 2005 BSI 12 January 2005 ISBN 0 580 45231 X National foreword This British Standard is the official English language version of EN 50289-3-10:2004:2004. The UK participation in its preparation was entrusted by Technical

3、 Committee EPL/46, Cables, wires and waveguides, R.F. connectors and accessories for communication and signalling, to Subcommittee EPL/46/1, Communication cables, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cr

4、oss-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or o

5、f British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text;

6、present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover,

7、 an inside front cover, the EN title page, pages 2 to 9 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 50289-3-10 NORME EUROPENNE EUROPISCHE NORM Decembe

8、r 2004 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2004 CENELEC - All rights of exploitation in any form and by any means re

9、served worldwide for CENELEC members. Ref. No. EN 50289-3-10:2004 E ICS 33.120.10 English version Communication cables Specifications for tests methods Part 3-10: Mechanical test methods Torsion and twisting Cbles de communication Spcifications pour les mthodes dessais Partie 3-10: Mthodes dessais m

10、caniques Torsion et vrillage Kommunikationskabel Spezifikationen fr Prfverfahren Teil 3-10: Mechanishe Prfverfahren - Torsion und Verdrillung This European Standard was approved by CENELEC on 2004-11-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate th

11、e conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exist

12、s in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electr

13、otechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN

14、50289-3-10:2005 - 2 - Foreword This European Standard was prepared by CENELEC Technical Committee TC 46X, Communication cables. The text of the draft was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 50289-3-10 on 2004-11-01. The following dates were fixed: latest da

15、te by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2005-11-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2007-11-01 This European Standard has been prepared under the

16、European Mandate M/212 given to CENELEC by the European Commission and the European Free Trade Association. _ - 3 - EN 50289-3-10:2004 Contents 1 Scope.4 2 Normative references.4 3 Definitions.4 4 Torsion 4 4.1 Sample4 4.2 Equipment.4 4.3 Procedure5 4.4 Requirements .6 4.5 Test report.6 5 Twisting.8

17、 5.1 Procedure 1.8 5.2 Procedure 2.8 5.3 Requirements .9 5.4 Test report.9 EN 50289-3-10:2005 - 4 - 1 Scope This Part 3-10 of EN 50289 details the method of test to determine the ability of a finished cable used in analogue and digital communication systems to withstand mechanical twisting and torsi

18、on. The primary purpose of the torsion test is to measure any variation in optical power transmittance of a fibre or electrical performance of a copper cable when the cable is subjected to torsional and twisting forces external to the cable jacket. A secondary purpose is to evaluate the possibility

19、of physical damage that may occur as a result of such stresses. The primary purpose of the twisting test is to determine the change of RL and NEXT caused when the cable assembly is subjected either to bending or twisting. It is to be read in conjunction with EN 50289-3-1, which contains essential pr

20、ovisions for its application. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) appli

21、es. EN 50289-3-1 2001 Communication cables - Specifications for test methods Part 1-1: Mechanical test methods General requirements EN 50290-1-2 2004 Communication cables - Part 1-2: Definitions 3 Definitions For the purposes of this European Standard the definitions of EN 50290-1-2 apply. 4 Torsion

22、 4.1 Sample The specimen shall be a sample of finished cable having a total length sufficient to permit the appropriate clamping and torsion, and long enough to permit optical transmittance or electrical measurements as required by the relevant cable specification. 4.2 Equipment The torsional appara

23、tus consists essentially of two cable gripping devices or clamps, one fixed and one that can rotate, supported as appropriate, and adjustable as to distance between them. The rotating clamp is connected to suitable turning equipment (e.g. a torquing lever). Any clamp supports, gripping devices, or t

24、orquing equipment used shall all be such as to permit access to both ends of the cable specimen for optical or electrical testing as may be required. Suitable apparatus is illustrated in Figures 1, 2 and 3. - 5 - EN 50289-3-10:2004 The cable gripping devices shall be such that - they may be tightene

25、d around the cable sufficiently to prevent movement within the grip, - the clamps hold the cable firmly in a straight line, - the clamps induce neither localized twisting damage on the cable caused by the inside edge of the clamp nor undue localized concentration of pressure on the cable, - the proc

26、ess of clamping does not induce any significant or accurately measurable attenuation increase (or no more than a negligible increase) in the specimen. If required by the relevant cable specification and/or to minimize specimen bending from a straight configuration, use weights or an appropriate load

27、ing mechanism to apply a tensile load to the cable gripping fixture (see Figures 1 and 3). The apparatus shall include test equipment to measure the change in optical or electrical performance as required in the relevant specification. 4.3 Procedure Install the specimen in the test apparatus such th

28、at the test length, L (see Figures 1, 2 and 3), is as required by the relevant cable specification. Take care to insure that no initial stress is applied to the specimen. Except for the necessary twisting operation, take care not to move or disturb the specimen ends throughout the test. Minimize spe

29、cimen sag (Figure 1 or 2) or vertical deviation from a straight line (Figure 3) as much as possible. If optical or electrical tests are required by the relevant cable specification, measure the unstressed specimen. Compare results with those after clamping to ensure that the clamping has not signifi

30、cantly degraded the cable performance. If not prohibited by the relevant cable specification, specimen sag or bend may be minimized by supporting the test length or by applying tension to the specimen cable between clamps. If required, apply tension as specified in the relevant cable specification t

31、o keep the specimen straight. If tension is required by the relevant cable specification, but specific tension loads are not stated, apply tension as shown in Table 1. Table 1 - Tension to be applied Nominal cable diameter range mm Minimum load N 2,5 15 2,6 to 4,0 25 4,1 to 6,0 40 6,1 to 9,0 45 9,1

32、to 13,0 50 13,1 to 18,0 55 18,1 to 24,0 65 24,1 to 30,0 70 30,1 75 If optical or electrical tests are required by the relevant cable specification, perform the required tests after clamping and application of tensile load. EN 50289-3-10:2005 - 6 - Rotate the movable cable clamp as follows: - rotate

33、180 clockwise; - return to the starting position; - rotate 180 counter-clockwise; - return to the starting position. This total four-part movement constitutes one cycle. Unless otherwise specified in the relevant cable specification, complete each cycle within 1 min, maximum, for a total of 10 cycle

34、s. During the final cycle (tenth), determine the number of transmitting fibres with the cable: - rotated 180 clockwise; - rotated 180 counter-clockwise; - with no rotation, after completion of the final cycle. Carry out the specified measurements. Allow the specimen to rest for a minimum period of 5

35、 min. If necessary, the sample may be removed from the apparatus for visual examination using normal corrected vision. 4.4 Requirements The acceptance criteria for the sample under test shall be stated in the relevant cable specification. Typical failure modes include loss of optical continuity, inc

36、rease in fibre loss, degradation of return loss, degradation of NEXT, and damage to the cable jacket or core components. 4.5 Test report The test report shall give the test conditions: - test length, L; - any tension which is to be applied; - number of fibres to be monitored for optical transmittanc

37、e; - maximum allowable change in optical or electrical performance; - temperature and record the pass/fail conditions as required in the relevant cable specification. L Sample Fixed cable clamp Rotating cable clamp Figure 1 - Cable torsion apparatus - 7 - EN 50289-3-10:2004 L Sample Fixed cable clam

38、p Rotating cable clamp Weight Figure 2 - Cable torsion apparatus with tension applied L Fixed clamp Sample Rotating clamp Weight Figure 3 - Alternative cable torsion apparatus with tension applied EN 50289-3-10:2005 - 8 - 5 Twisting 5.1 Procedure 1 A cable assembly which is in “U“ shape has to be co

39、nnected to a suitable network analyser (Figure 4a). During recording of the RL or the NEXT, the cable is wound around the mandrel for 180 (Figure 4b), unwound to the starting position, wound counter-clockwise for 180 around the mandrel (Figure 4c) and again unwound to its starting position. The init

40、ial position of the mandrel shall be chosen that only the straight parts of the “U“ will be bent during the test. Unless otherwise specified the radius of mandrel shall be 120 mm. Key DUT = device under test NWA = network analyser Figure 4 - Bending test: assembly in U shape 5.2 Procedure 2 A cable

41、assembly which is in “U“ shape has to be connected to a suitable network analyser (Figure 5a). During the recording of the RL and the NEXT the mandrel in the middle of the cable is first twisted in a clockwise direction for 180 (Figure 5b) then released to the starting position, twisted counter-cloc

42、kwise for 180 (Figure 5c) and again released to its starting position. NOTE Depending on the torsional rigidity and the maximum permissible torque at the cable connectors interface the maximum twist angle may have to be restricted. Unless otherwise specified the radius of mandrel shall be 120 mm. -

43、9 - EN 50289-3-10:2004 Key DUT = device under test NWA = network analyser Figure 5 Twisting test: assembly in U shape 5.3 Requirements The RL and NEXT shall not exceed the limits specified in the relevant relevant cable specification. 5.4 Test report The test report shall give the test conditions: -

44、 sample length, L; - radius of the mandrel; - number of fibres to be monitored for optical transmittance; - maximum allowable change in optical or electrical performance; - temperature and record the pass/fail conditions as required in the relevant cable specification. _ BS EN 50289-3-10: 2004 BSI 3

45、89 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are

46、updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Bri

47、tish Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automaticall

48、y receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http

49、:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic infor

展开阅读全文
相关资源
  • BS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdfBS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdf
  • BS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdfBS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdf
  • BS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdfBS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdf
  • BS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdfBS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdf
  • BS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdfBS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf
  • BS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdfBS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdf
  • BS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdfBS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdf
  • BS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdfBS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdf
  • BS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdfBS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdf
  • BS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdfBS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > BS

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1