1、BRITISH STANDARD BS EN 60264-3-3:1996 IEC 264-3-3: 1990 Incorporating Amendment No 1 to BS 7584-3-3:1992 (renumbers the BS as BS EN 60264-3-3: 1996) and incorporating Amendment No. 2 Packaging of winding wires Part 3-3: Taper barrelled delivery spools Specification for non-returnable spools made fro
2、m thermoplastic material The European Standard EN 60264-3-3:1994, with the incorporation of amendment A1:2004, has the status of a British Standard ICS 29.060.10 BS EN 60264-3-3:1996 This British Standard, having been prepared under the direction of the Cables and Insulation Standards Policy Committ
3、ee, was published under the authority of the Standards Board and comes into effect on 15 August 1992 BSI 5 May 2004 The following BSI references relate to the work on this standard: Committee reference CIL/55 Draft announced in BSI News May 1992 ISBN 0 580 21073 1 Committees responsible for this Bri
4、tish Standard The preparation of this British Standard was entrusted by the Cables and Insulation Standards Policy Committee (CIL/-) to Technical Committee CIL/55, upon which the following bodies were represented: British Cable Makers Confederation British Non-ferrous Metals Federation British Railw
5、ays Board Covered Conductors Association EEA (the Association of Electronics, Telecommunications and Business Equipment Industries) Electrical and Electronic Insulation Association Electronic Components Industry Federation Transmission and Distribution Association (BEAMA Ltd.) Amendments issued sinc
6、e publication Amd. No. Date Comments 9051 May 1996 15098 5 May 2004 See national forewordBS EN 60264-3-3:1996 BSI 5 May 2004 i Contents Page Committees responsible Inside front cover National foreword ii 1S c o p e 3 2 Normative references 3 3M a t e r i a l 3 4T y p e d e s i g n a t i o n 3 5R e q
7、 u i r e m e n t s 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications 6 Table 1 4 Table 2 4 Table 3 4 Table 4 5BS EN 60264-3-3:1996 ii BSI 5 May 2004 National foreword This British Standard has been prepared by Technical Committee
8、 GEL/55 (formerly CIL/55) and is the English language version of EN 60264-3-3:1994 Packaging of winding wires Part 3-3: Taper barrelled delivery spools Specification for non-returnable spools made from thermoplastic material, including amendment A1:2004, published by the European Committee for Elect
9、rotechnical Standardization (CENELEC). It is identical with IEC 60264-3-3:1990, including amendment 1:2003, published by the International Electrotechnical Commission (IEC). The start and finish of text introduced or altered by amendment is indicated in the text by tags !“. Tags indicating changes t
10、o CENELEC text carry the number of the CENELEC amendment. For example, text altered by CENELEC amendment A1 is indicated by !“. BS EN 60264, of which there are four Parts, deals with the packaging of winding wires. Part 1 covers containers, Part 2 covers cylindrical barrelled delivery spools, Part 3
11、 covers taper barrelled delivery spools and Part 4 covers methods of test. This British Standard is one of a series dealing with insulated wires used for windings in electrical equipment, which comprises the following three groups. IEC 60851, Methods of test for winding wires; IEC 60317, Specificati
12、ons for particular types of winding wires; IEC 60264, Packaging of winding wires. NOTE BS 6811 Winding wires Part 0:1993 General introduction and list of Parts lists the various Sections of BS 6811 and BS 7584 against the corresponding Parts of the IEC standards listed above. Some or all of these IE
13、C standards will be adopted as BS ENs in due course and the relevant Parts of BS 6811 and BS 7584 will be renumbered as BS ENs. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the secti
14、on entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Co
15、mpliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover. The copyright notice displayed in this do
16、cument indicates when the document was last issued.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60264-3-3 December 1994 + A1 March 2004 ICS 29.060.10 Supersedes HD 46.3.3 S1:1992 Descriptors: Winding, electric wire, insulated wire, delivery, spool, packaging, thermoplastic, specification, ma
17、rquage English version P a c k a g i n g o f w i n d i n g w i r e s P a r t 3 - 3 : T a p e r b a r r e l l e d d e l i v e r y s p o o l s Specification for non-returnable spools made from thermoplastic material (includes amendment A1:2004) (IEC 60264-3-3:1990 + A1:2003) Conditionnement des fils d
18、e bobinage Partie 3-3: Bobines de livraison ft de forme conique Spcification pour les bobines non rutilisables, faites de matriau thermoplastique (inclut lamemdement A1:2004) (CEI 60264-3-3:1990 + A1:2003) Verpackung von Wickeldrhten Teil 3-3: Lieferspulen mit konischem Kern Spezifikation fr Einweg-
19、Lieferspulen aus thermoplastischem Werkstoff (enthlt nderung A1:2004) (IEC 60264-3-3:1990 + A1:2003) This European Standard was approved by CENELEC on1994-09-01. Amendment A1 was approved by CENELEC on 2004-03-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which st
20、ipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Stan
21、dard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national
22、electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdo
23、m. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 2004 CENELEC All rights of exploitation in any form and by any means reserved w
24、orldwide for CENELEC members. Ref. No. EN 60264-3-3:1994 + A1:2004 EEN 60264-3-3:1994 BSI 5 May 2004 2 Foreword The text of the International Standard IEC 264-3-3:1990, prepared by IEC TC 55, Winding wires, was approved by CENELEC as HD 46.3.3 S1 on 1992-06-16. This Harmonization Document was submit
25、ted to the formal vote for conversion into a European Standard and was approved by CENELEC as EN 60264-3-3 on 1994-09-01. The following date was fixed: Annexes designated “normative” are part of the body of the standard. In this standard, Annex ZA is normative. Annex ZA is added by CENELEC. Foreword
26、 to amendment A1 The text of document 55/871/FDIS, future amendment 1 to IEC 60264-3-3:1990, prepared by IEC TC 55, Winding wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 60264-3-3:1994 on 2004-03-01. The following dates were fixed: Annex ZA h
27、as been added by CENELEC. latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1995-10-15 latest date by which the amendment has to be implemented at national level by publication of an identical national standar
28、d or by endorsement (dop) 2004-12-01 latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2007-03-01EN 60264-3-3:1994 BSI 5 May 2004 3 1 Scope This International Standard specifies the requirements for non-returnable taper barrelled delivery spools ma
29、de from thermoplastic material. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and par
30、ties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. IEC 60264-3-1:1989, Packaging of winding
31、wires Part 3: Taper barrelled delivery spools Section 1. Basic dimensions. !IEC 60264-4-1:1997 “, Packaging of winding wires Part 4: Methods of test Section 1. Delivery spools made from thermoplastic material. 3 Material The spools shall be made from thermoplastic material (for example modified poly
32、styrene) that satisfies the requirements given in this standard. The material used shall not have a deleterious effect on the conductor or the covering of the winding wire. 4 Type designation Taper barrelled delivery spools according to this standard shall be identified by dimensions d 1and l 1as sp
33、ecified in IEC 60264-3-1, for example as follows: Delivery spool !IEC 60264-3-3/IEC 250/400 “. 5 Requirements For test methods see IEC 60264-4-1. 5.1 Spool irregularities 5.1.1 Surface The surface of the spool shall be smooth and the flanges free from protruding material liable to damage the wire or
34、 injure the hands of the winding operator. 5.1.2 Construction Bolts and screws, if used in the construction of the spools, shall be countersunk so that the heads are below the surface. 5.2 Spool marking Each spool shall have embossed and/or engraved markings, located on the top side of the upper fla
35、nge, containing the following information: a) the type designation of the spool (for example !IEC 60264-3-3/IEC 250/400 “; b) name and/or trade mark of the spool manufacturer; c) year of manufacture; d) the nominal mass of the spool in grams; e) the words: “non-returnable”. The top flange shall be o
36、f such design as to allow the application of labels giving details of the manufacturer of the winding wire, its size, the !mass “ of winding wire on the spool, etc.EN 60264-3-3:1994 4 BSI 5 May 2004 5.3 Moss The mass of the spool shall comply with the value given in Table 1. There are no requirement
37、s for other spools. Table 1 5.4 Spool dimensions The spool dimensions and tolerances shall comply with the dimensions and tolerances given in IEC 60264-3-1. 5.5 True running deviations The true running deviations shall not exceed the value given in Table 1 of IEC 60264-3-1 (under y and z). 5.6 Behav
38、iour at high temperature The spool shall be conditioned !at a temperature of (60 3) C “. The spool dimensions and tolerances shall comply with the dimensions and tolerances given in IEC 60264-3-1. No swelling, buckling or variation in the flanges or in the barrel is permitted. 5.7 Impact test on fla
39、nges 5.7.1 Under normal ambient conditions The function of the spool shall not be destroyed after stressing with the value given in Table 2. There are no requirements for other spools. Table 2 5.7.2 At low temperature The spool shall be conditioned at a temperature from p10 C to p12 C. The function
40、of the spool shall not be destroyed after stressing with 70 % of the value given in Table 2. After conditioning at a temperature of p25 3 C the spool shall not be destroyed after stressing with 50 % of the value given in Table 2. 5.8 Deformation under load When stressed with the load specified in Ta
41、ble 3, the elongation shall not exceed the value given in Table 3. There are no requirements for other spools. Table 3 Spool type Mass Nominal g Tolerance % 250/400 315/500 150 0 250 0 2 2 Spool type Mass kg !Energy N m “ 250/400 315/500 3,0 3,0 25 28 Spool type Minimum tensile load kN Maximum elong
42、ation mm 250/400 315/500 25 40 3,15 4,0EN 60264-3-3:1994 BSI 5 May 2004 5 5.9 Flexibility test on flanges When stressed with the load specified in Table 4, the increase in distance between the flanges during and after stressing shall not exceed the value given in Table 4. There are no requirements f
43、or other spools. Table 4 Spool type Load Maximum increase in distance between flanges mm kN During stressing After stressing 250/400 315/500 8,0 12,5 5,0 6,3 0,315 0,315EN 60264-3-3:1994 6 BSI 5 May 2004 Annex ZA (normative) Normative references to international publications with their corresponding
44、 European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisi
45、ons of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. NOTE When the international publication has been modified by CENELEC common modifications, indicat
46、ed by (mod), the relevant EN/HD applies. IEC publication Date Title EN/HD Date 60264-3-1 1989 Packaging of winding wires Part 3: Taper barrelled delivery spools Section 1: Basic dimensions EN 60264-3-1 1994 !60264-4-1 1997 Packaging of winding wires Part 4.1: Methods of test Delivery spools made fro
47、m thermoplastic materials “7 blankBS EN 60264-3-3:1996 IEC 264-3-3: 1990 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the internationa
48、l level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would
49、 be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive th
