1、BRITISH STANDARDBS EN 60512-16-8: 2008Connectors for electronic equipment Tests and measurements Part 16-8: Mechanical tests on connections and terminations Test 16h: Insulating grip effectiveness (crimped connections)ICS 31.220.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g
2、40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 60512-16-8:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 August 2008 BSI 2008ISBN 978 0 580 5591
3、5 0National forewordThis British Standard is the UK implementation of EN 60512-16-8:2008. It is identical to IEC 60512-16-8:2008. The UK participation in its preparation was entrusted to Technical Committee EPL/48, Electromechanical components and mechanical structures for electronic equipment.A lis
4、t of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal
5、 obligations.Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARD EN 60512-16-8 NORME EUROPENNE EUROPISCHE NORM July 2008 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische N
6、ormung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-16-8:2008 E ICS 31.220.10 English version Connectors for electronic equipment - Tests and measurements -
7、Part 16-8: Mechanical tests on connections and terminations - Test 16h: Insulating grip effectiveness (crimped connections) (IEC 60512-16-8:2008) Connecteurs pour quipements lectroniques - Essais et mesures - Partie 16-8: Essais mcaniques des contacts et des sorties - Essai 16h: Efficacit du manchon
8、 isolant (connexions serties) (CEI 60512-16-8:2008) Steckverbinder fr elektronische Einrichtungen - Mess- und Prfverfahren - Teil 16-8: Mechanische Prfungen an Kontakten und Anschlssen - Prfung 16h: Isolationshalterung bei Crimpverbindungen (IEC 60512-16-8:2008) This European Standard was approved b
9、y CENELEC on 2008-06-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national s
10、tandards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and
11、notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lith
12、uania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Foreword The text of document 48B/1871/FDIS, future edition 1 of IEC 60512-16-8, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical compon
13、ents and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-16-8 on 2008-06-01. This standard is to be read in conjunction with EN 60512-1 and EN 60512-1-100 which explains the structure of the EN 60512 series. The f
14、ollowing dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2009-03-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2011-06-01 Annex ZA has be
15、en added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60512-16-8:2008 was approved by CENELEC as a European Standard without any modification. _ BS EN 60512-16-8:2008 2 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 16-8: Mechanical tests on connection
16、s and terminations Test 16h: Insulating grip effectiveness (crimped connections) 1 Scope and object This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in
17、a detail specification. The object of this part of IEC 60512 is to detail a standard test method to assess the effectiveness of an insulation grip to hold the insulation of a cable/wire under specified conditions. 2 Normative references The following referenced documents are indispensable for the ap
18、plication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512-1-1, Connectors for electronic equipment Tests and measurements Part 1-1: General examination Test 1a:
19、 Visual examination 3 Preparations 3.1 Preparation of specimen The specimens shall consist of even quantities of cable with the largest insulation specified for the grip, and the smallest. The specimens shall consist of a crimp contact or terminal end and the specified cable(s); these shall be prepa
20、red (crimped) in the manner given in the relevant detail specification or if none are given, the manufacturers instructions. The crimp contact/terminal end shall be crimped in the manner previously stated, but the cable/wire shall be held by the insulation grip only. NOTE Either crimping a separate
21、piece of wire or cutting the conductor after crimping may achieve this. The un-stripped cable/wire shall be at least 100 mm in length. If lubricant is required by the component detail specification, this shall be applied in the manner so specified. Similarly, if the manufacturers crimping or other a
22、ssembly devices specify a lubricant, this shall be applied. 3.2 Equipment A mandrel having a diameter equal to that as specified for the flexibility test of the relevant wire/cable shall be provided. BS EN 60512-16-8:2008 3 3.3 Pre-conditioning Any pre-conditioning of the samples required by the app
23、licable detail specification shall be applied. 4 Test method 4.1 Temperature It is recognized that temperature has a significant effect on the flexibility of cable insulation. These tests shall be carried out under normal laboratory conditions unless otherwise stated in the relevant detail specifica
24、tion. 4.2 Procedure The crimp(ed) contact/terminal shall be held tangential to the mandrel. The wire shall be wound around the mandrel for at least one complete turn and shall be in contact with the mandrel where it enters the insulation grip. Sufficient tension, as specified in the relevant detail
25、specification, shall be applied to the wire to keep it in contact with the mandrel. A test made by first winding the wire in one direction then in the opposite direction shall be considered one cycle. This cycle shall be done at least ten times. The rotational position of the specimen relative to th
26、e direction of bending shall be varied during each cycle such that forces are applied in at least four directions mutually at right angles to each other relative to the grip. NOTE It is recognized that grip devices have a best and worst direction of support. The above requirement is intended to test
27、 in both the best and worst directions. 4.3 Measurements and requirements 4.3.1 Before testing Visual examination according to IEC 60512-1-1 shall be carried out. There shall be no defects which would impair the validity of the test. 4.3.2 During testing None. 4.3.3 After testing The conductor shall
28、 be withdrawn from the cable/wire and examined for damage (caused by either the grip crimping process or the testing). This may be done by stripping the insulation from the far end of the cable/wire and applying a tensile load between the bared conductor and the crimp terminal. Visual examination ac
29、cording to IEC 60512-1-1 shall be done. There shall be no defects, other than those found under 4.3.1, which would impair the normal functioning of the component. 5 Details to be specified When this test is required by the detail specification, the following details shall be specified: a) whether pr
30、econditioning is required; b) cable/wire/insulation size(s) to be used; c) number of specimens to be tested for each grip size; BS EN 60512-16-8:2008 4 d) details of assembly tooling; e) whether lubricant, including that for application tooling, is to be used; f) whether special mounting of the spec
31、imen is required; g) tension to be applied; h) number of cycles (if other than 10); i) any deviation in from the standard test method. _ BS EN 60512-16-8:2008 5 Annex ZA(normative) Normative references to international publications with their corresponding European publications The following referen
32、ced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common mod
33、ifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60512-1-1 -1)Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination EN 60512-1-1 20022)1)Undated reference. 2)Valid edition at date of
34、 issue. BS EN 60512-16-8:2008 6 blankBS EN 60512-16-8: 2008BSI Group Headquarters389 Chiswick High Road,London W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards Institution (BSI)BSI is the independent national body responsible for preparing British Standards. It presents the UK view on
35、standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the qualit
36、y of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000 Fax: +44 (0)20
37、 8996 7400BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20
38、8996 9001 Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless other
39、wise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and
40、 services. Contact the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Members
41、hip Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publication
42、s. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photoco
43、pying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070 Email:
