1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationConnectors for electronic equipment Tests and measurementsPart 23-2: Screening and filtering tests Test 23b: Suppression characteristics of integral filtersBS EN 60512-23-2:2010N
2、ational forewordThis British Standard is the UK implementation of EN 60512-23-2:2010. It isidentical to IEC 60512-23-2:2010. It supersedes Test 23b from BS 5772-9:1993, IEC 60512-9:1992, which will remain current until all the tests it contains have been revised.The UK participation in its preparati
3、on was entrusted to Technical CommitteeEPL/48, Electromechanical components and mechanical structures for electronic equipment.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of
4、 acontract. Users are responsible for its correct applica-tion. BSI 2010 ISBN 978 0 580 62174 1 ICS 31.220.10Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 O
5、ctober 2010.Amendments issued since publicationDate Text affectedBRITISH STANDARDBS EN 60512-23-2:2010EUROPEAN STANDARD EN 60512-23-2 NORME EUROPENNE EUROPISCHE NORM September 2010 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europis
6、ches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-23-2:2010 E ICS 31.220.01 English version Connectors for electronic equipm
7、ent - Tests and measurements - Part 23-2: Screening and filtering tests - Test 23b: Suppression characteristics of integral filters (IEC 60512-23-2:2010) Connecteurs pour quipements lectroniques - Essais et mesures - Partie 23-2: Essais dcrantage et de filtrage - Essai 23b: Caractristiques de coupur
8、e des filtres intgraux. (CEI 60512-23-2:2010) Steckverbinder fr elektronische Einrichtungen - Mess- und Prfverfahren - Teil 23-2: Prfungen der Schirmung und Dmpfung - Prfung 23b: Einfgungsdmpfung von integrierten Filtern (IEC 60512-23-2:2010) This European Standard was approved by CENELEC on 2010-09
9、-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obta
10、ined on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Cent
11、ral Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxe
12、mbourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 60512-23-2:2010 - 2 - Foreword The text of document 48B/2150/FDIS, future edition 1 of IEC 60512-23-2, prepared by SC 48B, Connectors, of IEC TC 48, Electromec
13、hanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-23-2 on 2010-09-01. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN
14、and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2011-06-01 latest date by which the na
15、tional standards conflicting with the EN have to be withdrawn (dow) 2013-09-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60512-23-2:2010 was approved by CENELEC as a European Standard without any modification. _ BS EN 60512-23-2:2010- 3 - EN
16、60512-23-2:2010 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated referenc
17、es, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year CISPR 17 1981 Methods of measurement of the suppre
18、ssion characteristics of passive radio interference filters and suppression components - - BS EN 60512-23-2:2010 4 60512-23-2 IEC:2010 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 23-2: Screening and filtering tests Test 23b: Suppression characteristics of integral filters 1 Scope
19、 and object This part of IEC 60512, when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard method to me
20、asure suppression characteristics (insertion loss) introduced by single and multiple circuit radio-frequency filters which are an integral part of a connector. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only
21、 the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. CISPR 17:1981, Methods of measurement of the suppression characteristics of passive interference filters and suppression components 3 Preparation of the specimen The
22、specimen shall be unwired and shall be mounted in a test fixture as described in the detail specification. 4 Measurement procedure The suppression characteristics shall be measured according to CISPR 17, using the test circuit A1 or A2 as relevant. 5 Requirements The measured suppression characteris
23、tics shall not be less than the minimum values specified in the detail specification. 6 Details to be specified When this test is required by the detail specification, the following details shall be specified: a) preparation of the specimen; b) mounting of the specimen and details of the test fixtur
24、e; c) test frequency or frequency range; d) load current, when required; e) system impedance; BS EN 60512-23-2:201060512-23-2 IEC:2010 5 f) test method; g) minimum values of insertion loss; h) any deviation from the standard test method. _ BS EN 60512-23-2:2010This page deliberately left blankThis p
25、age deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British St
26、andards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions
27、.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside
28、 frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and
29、hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for inter
30、national standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +
31、44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and rece
32、ive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at inf
33、ormation about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduc
34、ed, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email:
